Users Also Read

MCQ's Search Engine

Electrical Engineering

Mechanical Engineering

Civil Engineering

Automobile Engineering

Chemical Engineering

Computer Engineering

Electronics Engineering

Medical Science Engg

Q1. | If the dynamic viscosity of a fluid is 0.5 poise and specific gravity is 0.5, then the kinematic viscosity of that fluid in stokes is |

A. | 0.25 [Wrong Answer] |

B. | 0.50 [Wrong Answer] |

C. | 1.0 [Correct Answer] |

D. | none of the above [Wrong Answer] |

View Answer
Explanation:-
Answer : CDiscuss it below :Zenithraja .S Said on 2020-05-03 23:46:19specific gravity=0.5 To find:kinematic viscosity in stokes Answer: 1 poise=
0.1 N-s/m specific gravity= density of any fluid/density of water here specific value given as 0.5 we know that density of standard fluid(water) =1000kg\m density of any fluid= specific gravity*density of standard water = 0.5*1000 =500 kinematic viscosity= dynamic viscosity\ density of given fluid =0.05\500
=0.0001 m 1 stokes= 0.0001 m ANSWER=1 stoke
Rohit punia Said on 2019-06-21 23:09:28dynamic viscosity divided by specific gravity Zakir Hussain Said on 2018-11-11 09:29:23explane this qestion plz !! OOPS Login [Click here] is required to post your answer/resultHelp other students, write article, leave your comments |

**Also Read Similar Questions Below :**

⇒ Select the incorrect statement.

The pressure intensity at vena contracta is atmospheric.

Contraction is least at vena contracta.

Stream lines are parallel throughout the jet at vena contracta.

Coefficient of contraction is always less than one.

⇒ The distance from pipe boundary, at which the turbulent shear stress is one-third die wall shear stress, is.

1/3 R

1/2 R

2/3 R

3/4R

⇒ A fluid of kinematic viscosity 0.4 cm2/sec flows through a 8 cm diameter pipe. The maximum velocity for laminar flow will be

less than 1 m/sec

1 m/sec

1.5 m/sec

2 m/sec

⇒ Select the correct statement.

The absolute roughness of a pipe de-creases with time.

A pipe becomes smooth after using for long time.

The friction factor decreases with time.

The absolute roughness increases with time.

⇒ If the velocity is zero over half of the cross-sectional area and is uniform over the remaining half, then the momentum correction factor is.

1

4/3

2

4

⇒ Action of a point-gun is based on

Bernoulli's principle

Boyle's law

Faraday's law

Archimedes' principle

⇒ Specific speed is

Dimensionless

Measured in rev/min.

A speed

A shape factor

⇒ A floating body is said to be in a state of stable equilibrium.

when its metacentric height is zero

when the metacentre is above the centre of gravity

when the metacentre is below the centre of gravity

only when its centre of gravity is below its centre of buoyancy

⇒ A hydrogen bal loon released on the moon would

Climb up with an acceleration of 9.8 m/sec

^{2}

Climb up with an acceleration of 9.8 x 6 m/sec

^{2}

Neither climb nor fall

Fall with an acceleration of 9.8/6 m/sec

^{2}

⇒ If the weight of a body immersed in a fluid exceeds the buoyant force, then the body will

rise until its weight equals the buoyant force

tend to move downward and it may finally sink

float

none of the above

⇒ The thickness of boundary layer at the leading, (entrance) edge will be

Maximum

Minimum

Zero

Average

⇒ Bernoulli's theorem deals with the principle of conservation of

Energy

Momentum

Mass

Force

⇒ Across the boundary layer, pressure remains

More

Less

Constant

Zero

⇒ Weir may also be used to measure

Velocity of flow

Pressure

Discharge in a river or channel

Kinetic energy

⇒ For hydro-dynamically smooth boundary, the friction coefficient for turbulent flow is

constant

dependent only on Reynolds number

a function of Reynolds number and relative roughness

dependent on relative roughness only

⇒ The theoretical value of coefficient of contraction of a sharp edged orifice is

0.611

0.85

0.98

1.00

⇒ The viscosity of a gas

decreases with increase in temperature

increases with increase in temperature

is independent of temperature

is independent of pressure for very high pressure intensities

⇒ If a sphere of diameter 1 cm falls in castor oil of kinematic viscosity 10 stokes, with a terminal velocity of 1.5 cm/sec, the coefficient of drag on the sphere is

less than 1

between 1 and 100

160

200

⇒ The water jet after striking a stationary flat plate will be deflected at an angle of

60°

90°

110°

135°

⇒ If the velocity is zero over half of the cross-sectional area and is uniform over the remaining half, then the momentum correction factor is

1

4/3

2

4

⇒ The position of center of pressure on a plane surface immersed vertically in a static mass of fluid is.

at the centroid of the submerged area

always above the centroid of the area

always below the centroid of the area

none of the above

⇒ Metacentric height for small values of angle of heel is the distance between the

centre of gravity and centre of buoy-ancy

centre of gravity and metacentre

centre of buoyancy and metacentre

free surface and centre of buoyancy

⇒ A gale blows over a house. The force due to the gale on the roof is

Downward

Upward

Horizontal

Zero

⇒ Which of the following is an incorrect statement ?

Coefficient of contraction of a venturimeter is unity.

Flow nozzle is cheaper than venturimeter but has higher energy loss.

Discharge is independent of orientation of venturimeter whether it is horizontal, vertical or inclined.

None of the above statement is correct.

⇒ Equation of continuity is based on the principle of conservation of

mass

energy

momentum

none of the above

⇒ The power channel that extends from the intake works to the power house is called

Lead race

Head race

Diversion canal

Penstock

⇒ Which of the following is used to measure the discharge ?

current meter

venturimeter

pitot tube

hotwire anemometer

⇒ The speed of a pressure wave through a pipe depends upon

the length of pipe

the viscosity of fluid

the bulk modulus for the fluid

the original head

⇒ The pressure drag depends upon

The boundary layer formation

The separation of boundary layer

The size of wake

Both (B) and (C) above

⇒ If velocity is zero over l/3rd of a cross-section and is uniform over remaining 2/3rd of the cross-section, then the correction factor for kinetic energy is.

4/3

3/2

9/4

27/8