Question is ⇒ If t be the thickness of the laminations, then eddy current loss in a generator. will vary as, Options are ⇒ (A) 1/t, (B) 1/t2, (C) t, (D) t2, (E) , Leave your comments or Download question paper.

Question is ⇒ If t be the thickness of the laminations, then eddy current loss in a generator. will vary as, Options are ⇒ (A) 1/t, (B) 1/t2, (C) t, (D) t2, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	If t be the thickness of the laminations, then eddy current loss in a generator. will vary as
A.	¹/_t [Wrong Answer]
B.	¹/_t² [Wrong Answer]
C.	t [Wrong Answer]
D.	t² [Correct Answer]
View Answer 7 -2 Explanation:- Answer : D Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Regenerative braking on D.C. shunt motors is used when
the load has overhauling characteristics
the load is variable
the load also acts as a braking force
the load is constantly decreasing

⇒ Which of the following method of speed control, of D.C. machine will offer minimum efficiency ?
Voltage control method
Field control method
Armature control method
All above methods

⇒ If the field circuit of a loaded shunt motor is suddenly opened
torque developed by the motor would be reduced to zero
it would race to almost infinite speed
it would draw abnormally high armature current
the fuse or circuit breaker will open the circuit before too much damage is done to the motor

⇒ The variable resistor shunting the field of a D.C. series motor is called a
armature divertor
voltage regulator
field divertor
potential divider

⇒ Which of the following motors is most suitable for signalling devices and many kinds of timers ?
D.C. shunt motor
D.C. series motor
Induction motor
Reluctance motor

⇒ The speed of a D.C. shunt motor can be increased by
increasing the resistance in armature circuit
increasing the resistance in field circuit
reducing the resistance in the field circuit
reducing the resistance in the armature circuit

⇒ The speed of a D.C. motor, under constant load conditions, is affected by
back e.m.f.
field flux
armature current
none of the above

⇒ Which of the following application requires high starting torque ?
Lathe machine
Centrifugal pump
Locomotive
Air blower

⇒ In a D.C. series motor, if the armature current is reduced by 50%, the torque of the motor will be equal to
100% of the previous value
50% of the previous value
25% of the previous value
10% of the previous value

⇒ The hysteresis loss in a D.C. machine least depends on
Frequency of magnetic reversals
Maximum value of flux density
Volume and grade of iron
Rate of flow of ventilating air

⇒ D.C. generators are installed near the load centres to reduce
iron losses
line losses
sparking
corona losses

⇒ At the instant of starting when a D.C. motor is put on supply, it behaves like
a highly resistive circuit
a low resistance circuit
a capacitive circuit
none of the above

⇒ The condition for maximum power in case of D.C. motor is
back e.m.f. = 2 x supply voltage
back e.m.f. = 1/2 x supply voltage
supply voltage = 1/2 x back e.m.f.
supply voltage = back e.m.f.

⇒ The speed of a D.C. shunt motor is required to be more than full load speed. This is possible by
reducing the field current
decreasing the armature current
increasing the armature current
increasing the excitation current

⇒ A brake test on D.C. motors is usually restricted to
small horse power motors
variable speed motors
high speed motors
open frame type motors.

⇒ For starting a D.C. motor a starter is required because
it limits the speed of the motor
it limits the starting current to a safe value
it starts the motor
none of the above

⇒ If T_a be the torque and Ia the armature current for a D.C. motor, then which of the following relation is valid before saturation ?
T_a ∝ I_a
T_a ∝ I/I_a
T_a ∝ I_a²
T_a ∝ ^I/_{I_a²}

⇒ The losses occurring in a D.C. generator are given below. Which loss is likely to have highest proportion at rated load of the generator ?
hysteresis loss
field copper loss
armature copper loss
eddy current loss

⇒ Which of the following statements is correct, in case of a D.C. series motor ?
It should be directly connected to the load
It may run away if its field becomes open
It is a constant speed motor
It cannot be used where high starting torque is required

⇒ D.C. generators are normally designed for maximum efficiency around
full-load
rated r.p.m.
rated voltage
all of the above

⇒ The direction of rotation of a D.C. series motor can be changed by
interchanging supply terminals
interchanging field terminals
either of (a) and (b) above
None of the above

⇒ The purpose of retardation test on D.C. shunt machines is to find out
stray losses
eddy current losses
field copper losses
windage losses

⇒ When the speed of a D.C. motor increases
back e.m.f. increases and current drawn decreases
back e.m.f. as well as current drawn both increase
back e.m.f. as well as current drawn both decrease
back e.m.f. decreases and current drawn increases

⇒ Which loss in a D.C. generator varies with load ?
Copper loss
Eddy current loss
Hysteresis loss
Windage loss

⇒ A wide and very sensitive speed control is usually required in case of
elevators
steel rolling mills
colliery winders
all of the above

⇒ In hazardous area of gassy mines, material transportation is done by vehicles powered by
A.C. mains
D.C. mains
I.C. engines
batteries

⇒ Which of the following steps is likely to result in reduction of hysteresis loss in a D.C. generator ?
Providing laminations in armature core
Providing laminations in stator
Using non-magnetic material for frame
Using material of low hysteresis coefficient for armature core material

⇒ The hysteresis loss in a D.C. generator varies with the frequency of magrietic reversals as
1/f
f
f^1.6
f²

⇒ One D.C. motor drives another D.C. motor. The second D.C. motor when excited and driven
runs as a generator
does not run as a generator
also runs as a motor
comes to stop after sometime

⇒ If t be the thickness of the laminations, then eddy current loss in a generator. will vary as
¹/_t
¹/_t²
t
t²