Question is ⇒ If resistance is 20 Ω and inductance is 2 H in a R-L series circuit, then time constant of this will be, Options are ⇒ (A) 0.001 s, (B) 0.1 s, (C) 10 s, (D) 100 s, (E) , Leave your comments or Download question paper.

Question is ⇒ If resistance is 20 Ω and inductance is 2 H in a R-L series circuit, then time constant of this will be, Options are ⇒ (A) 0.001 s, (B) 0.1 s, (C) 10 s, (D) 100 s, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	If resistance is 20 Ω and inductance is 2 H in a R-L series circuit, then time constant of this will be
A.	0.001 s [Wrong Answer]
B.	0.1 s [Correct Answer]
C.	10 s [Wrong Answer]
D.	100 s [Wrong Answer]
View Answer 2 -1 Explanation:- Answer : B Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The resistance of a photoconductor
increases with increase in light intensity
decreases with increase in light intensity
may increase or decrease with increase in light intensity
remains constant

⇒ In amplitude modulation, the magnitude of side bands is
ma/2 times the carrier amplitude, E_c
ma times the carrier amplitude, E_c
2ma times the carrier amplitude, E_c
4ma times the carrier amplitude, E_c

⇒ D-layer extends approximately from
50 to 90 km
20 to 50 km
90 to 110 km
up to 50 km

⇒ In log magnitude Bode diagram the slope of high frequency asymptote of (1 + jωT) is
20 dB per decade
10 dB per decade
20 dB per octave
10 dB per octave

⇒ In a varistor the v-i graph is linear.
TRUE
FALSE

⇒ For a P-N junction diode, the current in reverse bias may be
few amperes
between 0.5 A and 1 A
few milliamperes
few micro or nanoamperes

⇒ If a and b are the width and height of rectangular wave-guide the cut off wavelength λ_c for TE₂₀ mode is equal to
a
a + b
a - b
a² + b²

⇒ For holding the drain current constant in spite of large changes in JFET parameters
current source bias is used
voltage divider bias is used
reverse bias is used
no bias is used

⇒

Assertion (A): When a photoconductive device is exposed to light, its bulk resistance increases.

Reason (R): When exposed to light, electron hole pairs are generated in the photoconductive device.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not a correct explanation of A
A is true but R is false
A is false but R is true

⇒ Which statement out of the following statement is wrong?
Attenuation of satellite signals by rain and fog varies almost inversely with the angle of elevation
At 12/4, GHz link frequencies, signal power loss due to rain and fog is much greater than at 4/6 GHz frequencies
The distance between satellite and Earth station varies slightly with angle of elevation
At present 4/6 GHz geostationary satellites are being parked in geosynchronous, orbits at least 10° apart

⇒ The transconductance curve of a JFET is
a straight line
parabolic
hyperbolic
inverted V-type

⇒ A carrier is modulated by two modulating waves A and B having modulation indices of 0.6 and 0.8 respectively. The overall modulation index is
1
0.7
0.2
1.4

⇒ The phase angle of lead circuit is
between 0 and -90°
between 0 and +90°
90°
more than 90°

⇒ What will be maximum input that can be converted for a 6 bit dual slope A/D converter uses a reference of -6v and a 1 MHz clock. It uses a fixed count of 40 (101000).
9 V
9.45
10 V
8 V

⇒ If there is phase error in the carrier signal for the detection of SSB signals, then
the output gets reduced, but a phase distortion results
the output is not reduced, but a phase distortion results
the output is not reduced, and also no distortion
the output is reduced, no phase distortion

⇒ In 8085, which instructions are useful for writing and using subroutines?
CALL
RET
CALL and RET
none of the above

⇒ The decimal equivalent of the hexadecimal number E 5 is
279
229
327
0

⇒ Consider the followings statements: A multiplier

selects one of the several inputs and steers it to the output
routes the data from a single input to many outputs
converts parallel data into serial data
is a combinational circuit

On the above statements which are correct?
1, 2, 4
2, 3, 4
1, 3, 4
1, 2, 3

⇒ The gain of a current element is
0 dB
1.67 dB
1.76 dB
3 dB

⇒

Assertion (A): Stubs, directional couplers and baluns are very commonly used in communication systems

Reason (R): Characteristic impedance of a line is an important parameter.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct but R is wrong
A is wrong but R is correct

⇒ In a single phase full wave regulator feeding an R-L load, the power factor angle of load is θ. The range of control of firing angle a is
0 ≤ a ≤ p
θ ≤ a ≤ p
0 ≤ a ≤ (p - θ)
θ ≤ a ≤ (p + θ)

⇒ Which of the following is a vector quantity?
Standing wave ratio
Reflection coefficient
Gain
All of the above

⇒ RS latch can be built with
NOR gates
NAND gates
NOR or NAND gates
none of the above

⇒ In 8085, Whenever a signal is received at TRAP terminal its program execution is transferred to a subroutine on address __________ .
0000 H
0024 H
002 CH
provided by the address generation logic

⇒ For a symmetrical network
h₁₁ = h₂₂
h₁₂ = h₂₁
h₁₁ h₂₂ - h₁₂ h₂₁ = 0
h₁₁ h₂₂ - h₁₂ h₂₁ = 1

⇒ In a push pull circuit the two transistors are
both pnp
both npn
one pnp and other npn
either (a) or (b)

⇒ The elements which become superconducting at extremely low temperatures are
good conductors at room temperature
ferromagnetic at room temperature
relatively poor conductors at room temperature
insulators at room temperature

⇒ In figure the dc emitter current of each transistor is a
4 mA
2 mA
3 mA
1 mA

⇒ Java variables are called
instance variables, class variables and global variables
instance variables, class variables and local variables
instance variables, class variables and sector variables
global variables, class variables and local variables

⇒ An AC circuit has two branches in parallel. The current in one branch is 5 A. Then the current source
must be less than 5 A
must be more than 5 A
may be equal or more or less than 5 A
0.208333333333333