Question is ⇒ If J, I and a denote current density, current and area of cross section of a conductor, then, Options are ⇒ (A) J = Ia, (B) J = I/a2, (C) J = I/a, (D) J = Ia2, (E) , Leave your comments or Download question paper.

Question is ⇒ If J, I and a denote current density, current and area of cross section of a conductor, then, Options are ⇒ (A) J = Ia, (B) J = I/a2, (C) J = I/a, (D) J = Ia2, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	If J, I and a denote current density, current and area of cross section of a conductor, then
A.	J = Ia [Wrong Answer]
B.	J = I/a² [Wrong Answer]
C.	J = I/a [Correct Answer]
D.	J = Ia² [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Efficiency of a half wave diode rectifier is less than 40%.
TRUE
FALSE

⇒ If the temperature of an extrinsic semiconductor is increased so that the intrinsic carrier concentration is doubled, then
the majority carrier density is doubled
the minority carrier density is doubled
the minority carrier density becomes 4 times the original value
both the majority and minority carrier densities double

⇒ The hexadecimal number 5 F is equal to binary number
1010011
1011001
1010101
1011111

⇒ Which of the following statements is not true in regard to storage time of a diode?
During this time, the diode is reverse-biased
The diode conducts during this time
It is due to the time taken by carriers to depart from the function when the diode is reverse-biased
During this time the diode current is zero

⇒

Assertion (A): A multiplexer can be used for data routing.

Reason (R): A multiplexer has one input and many outputs.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is true, R is false
A is false, R is true

⇒ A piezoelectric force transducer has a charge sensitivity of 20 pC/N. It is connected to a charge amplifier and overall gain of transducer and amplifier is 50 mV/N. The gain of amplifier is
1 mV/pC
1.5 mV/pC
2.5 mV/pC
4 mV/pC

⇒ Which one of the following is true for EM wave propagation through rectangular waveguide of cross-section 2a x a
critical wavelength for TE₁₀ mode is the same as that for TE₀₂ mode
critical wavelength for TE₁₀ mode is one half of that for TE₁₀ mode
critical wavelength for TE₁₀ mode is the same as that for TM₁₀ mode
critical wavelength for TE₁₀ mode is double that for TE₀₁mode

⇒ In ferromagnetic materials, the orientation between neighbouring permanent dipoles is parallel.
TRUE
FALSE

⇒ The maximum number of AM broadcast stations that can be accommodated in a 100 kHz bandwidth for the highest modulating frequency of 5 kHz will be
100
20
10
1

⇒ The primary function of lag compensator is to provide sufficient
gain margin
phase margin
both gain margin and phase margin
either (a) or (b)

⇒ A few minutes disturbance in space communications occurs twice a year during Sunblinding when __________ are in line.
Sun and satellite
Sun and Earth station
Satellite and Earth station
Sun, satellite and Earth station

⇒

Assertion (A): Gate triggering is the most commonly used method for triggering of an SCR.

Reason (R): Even a small gate current is sufficient to turn on an SCR.

Both A and R are correct and R is correct explanation of A
Both A and R correct but R is not correct explanation of A
A is correct but R is wrong
A is wrong but R is correct

⇒ The network shown in the figure represen
band pass filter
low pass filter
high pass filter
band stop filter

⇒ A class B chopper operates in third quadrant.
TRUE
FALSE

⇒ An LED has a rating of 2 V and 10 mA. It is used along with 6V battery. The range of series resistance is
0 to 200 Ω
200 - 400 Ω
200 Ω and above
400 Ω and above

⇒ For a type 0 system and unit ramp input, the steady state error is
0
∞
1
1/K_V

⇒ A P-channel MOSFET operating in the enhancement mode is characterized by V_t = - 4 V and I_DQ = - 10 mA, when V_GSQ = - 5.5 V, what will be V_GSQ if I_DQ = -15 mA and I_{D, on} = - 16 mA
- 2 V
3 V
0.13 V
1.3 V

⇒ A system has 12 poles or 2 zeros. Its high frequency asymptote in its magnitude plot has slope of
-200 dB/decade
-240 dB/decade
-280 dB/decade
-320 dB/decade

⇒ In figure the current through resist
is always equal to 130 mA
may vary between 130 mA and 10 mA
may vary between 65 mA and 10 mA
is always equal to 65 mA

⇒ Which of the following modulation is analog in nature?
PCM
DPCM
DM
PDM

⇒ The gain of collinear arrays is maximum when the spacing between the elements is
0.1 λ to 0.3 λ
0.3 λ to 0.9 λ
0.5 λ to 0.7 λ
0.7 λ to 0.9 λ

⇒ For aeroplane and navigation frequency band is
VLF
UHF
VHF
EHF

⇒ For a wave v = V _1m sin (ωt + θ₁ ) - V_3m sin (3ωt + θ₃), the rms value is (0.5 V²_1m + 0.5 V²_3m)^0.5
TRUE
FALSE

⇒ Advanced low power Schottky is a part of
ECL family
CMOS family
TTL family
none of the above

⇒ Δ²V = - r/E is known as __________ equation
Poisson
Fourier
Laplace
Maxwell

⇒ The D'Arsonval- movement can be converted into audio frequency ac ammeter by adding a
thermocouple
transducer
chopper
rectifier

⇒ A 3 x 8 decoder with two enable inputs is to be used to address 8 blocks of memory. What will be the size of each memory block when addressed from a sixteen bit bus with two MSBs used to enable the decoder?
2 K
4 K
16 K
64 K

⇒

Match the following:

	List I		List II
A.	Ratio of maximum energy stored to energy dissipated per cycle	1.	Propagation constant
B.	TEM mode is loss less medium	2.	Cutoff frequency is zero
C.	Ratio of frequency in radian to phase velocity of EM wave	3.	Quality factor of cavity
D.	TEM is the mode of lowest cutoff frequency	4.	Cylindrical waveguide

A-3, B-2, C-4, D-1
A-2, B-3, C-1, D-4
A-3, B-2, C-1, D-4
A-2, B-3, C-4, D-1

⇒ The mobile unit of a mobile telephone is generally in
vehicles
pocket
office
vehicle or pocket

⇒ The conversion or collector circuit efficiency is a measure
how successfully the active device converts D.C. power to A.C. signal power
how much distortion in output is reduced with respect to input
how successfully the active device converts A.C. power to D.C. signal power
none of the above