Question is ⇒ If re is ac resistance of diode, the Thevenin input impedance of a differential amplifier is, Options are ⇒ (A) re, (B) bre, (C) 2 bre, (D) 0.5 bre, (E) , Leave your comments or Download question paper.

Question is ⇒ If re is ac resistance of diode, the Thevenin input impedance of a differential amplifier is, Options are ⇒ (A) re, (B) bre, (C) 2 bre, (D) 0.5 bre, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	If r_e is ac resistance of diode, the Thevenin input impedance of a differential amplifier is
A.	r_e [Wrong Answer]
B.	br_e [Wrong Answer]
C.	2 br_e [Correct Answer]
D.	0.5 br_e [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The surface charge density on a conductor is 1.55 x 10^-9C/m². The conductor is immersed in water with ε = 78ε₀.The electric field will be __________ .
3 V/m
1.55 V/m
2 V/m
2.25 V/m

⇒ Which of the following directives in 8085 causes two bytes to be reserved in the memory?
D S
D B
D W
E Q U

⇒ A difference amplifier using op-amp has closed loop gain = 50. If input is 2 V to each of inverting and non-inverting terminals, output is 5 mA. Then CMRR =
20000
2000
200
20

⇒ Friction forces acts in a direction
opposite to that of velocity
same as that of velocity
at right angle to that of velocity
partly opposite and partly at right angle to the direction of velocity

⇒ A square current wave of magnitude 1 A is applied to an element for 5 seconds. The voltage across the element rises linearly from 0 to final value linearly. The element is
resistance
inductance
capacitance
R and C in series

⇒ If A = 4∠7°, A² is
16∠14°
16∠49°
16∠7°
16∠3.5

⇒ The Ebers-moll equation for I_E in CB configuration is given by
I_E = a_nI_CI_EC0
I_E = a_II_C + I_C0
I_E = a_nI_C + I_C0(e^qVEB/KT-1)
I_E = a_II_C + I_E0(e^qV_EB/KT - 1)

⇒ In 8085, the pins for SID and SOD are
4 and 5 respectively
5 and 4 respectively
3 and 4 respectively
4 and 3 respectively

⇒ In a flip flop which input determines the state to which output will transistion?
Control input
Clock input
Both control and clock input
Either control or clock input

⇒ If the secondary winding of CT is opened when primary coil is carrying current
transformer will burn immediately
there will be weak flux density in core
there will be very high induced voltage in secondary
there will be high current in secondary

⇒ The transient currents are due to
resistance of the circuit
impedance of the circuit
voltage applied to the circuit
changes in stored energy in inductors and capacitors

⇒ The Y plates of a CRO are excited by a voltage 2 sin 100 t and the X plates are not connected. The display would be
a vertical line
a horizontal line
sine wave
slant line

⇒ Linear diode detector utilizes
linear portion of static characteristics of diode
linear portion of dynamic characteristic of diode
square law portion of dynamic characteristics of diode
rectification property of diode

⇒ A first order element yields almost exact duplication only for constant or slowly varying phenomenon.
TRUE
FALSE

⇒ A bistable multivibrator
has no stable state
has one stable state
has two stable state
none of the above

⇒ Maximum power transfer theorem is applicable to circuits with one source only.
TRUE
FALSE

⇒ The rotation of direction of E field of a linearly polarized wave passing through a magnetised ferric medium is called
Lorentz rotation
Faraday rotation
Steinmitz rotation
Fleming's rotation

⇒ For matrix A, A^-1 A = 1
TRUE
FALSE

⇒ The method of frequency compensation in moving iron voltmeter is
to use a capacitor in series with coil
to connect a capacitor in parallel with coil
to connect a capacitor in parallel with series resistance
none of the above

⇒ If input frequency is 50 Hz, the frequency of output wave in a full wave diode rectifier circuit is
25 Hz
50 Hz
100 Hz
200 Hz

⇒ The conductivity of materials found in nature ranges from 10⁹ ohm^-1m^-1 to nearly 10¹⁸ ohm^-1 m^-1 from this it can be concluded that the conductivity of silicon in ohm^-1 cm^-1 will be nearly
0.5 x 10^-15
0.5 x 10^-21
0.5 x 10^-12
0.5 x 10^-3

⇒ The forbidden energy gap between the valence band and conduction band will be least in case of
metals
semiconductors
insulators
all of the above

⇒ Which of the following statement is correct for two wattmeters method of power measurement in 3 phase circuit?
Power can be measured by this method only for star connected loads
When two wattmeters have equal readings power factor is 0.5.
When power factor is 1, one of the wattmeters readings is zero
When the two wattmeter read equal and opposite, p.f. is zero.

⇒ The Hilbert transform of cos ω₁t + sin ω₂t is
sin ω₁t + cos ω₂t
sin ω₁t - cos ω₂t
cos ω₁t - cos ω₂t
- sin ω₁t + cos ω₂t

⇒

Assertion (A): Water waves are longitudinal but EM waves are transverse

Reason (R): In an EM wave electric field, magnetic field and propagation are mutually perpendicular.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct but R is wrong
A is wrong but R is correct

⇒

Assertion (A): A low power factor wattmeter has special constructional features to ensure accurate measurement.

Reason (R): Extension of wattmeter range in dc circuit can be easily done by using current and potential transformer.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not correct explanation of A
A is true R is false
A is false R is true

⇒

Assertion (A): In two wattmeter method of 3 phase power measurement, one of the wattmeters would read negative if power factor of load is less than 0.5.

Reason (R): In two wattmeter method of 3 phase power measurement, both the wattmeters would show equal readings if power factor of load is unity.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not correct explanation of A
A is true R is false
A is false R is true

⇒ If the sign bit of mantissa is 0 and the exponent is increased from a positive to a more negative number the result is
a larger floating point number
a smaller floating point number
either (a) or (b) depending on the actual number
a negative floating point number

⇒ The most important primary force of attraction in the formation of solids is
electromagnetic
electrostatic
quantum-electrostatic
quantum electromagnetic

⇒ In filter system of sideband suppression the advantage of using mechanical filter is
smaller size
good bandpass
good attenuation characteristics
all of the above