Question is ⇒ If initial value of <code>PROD</code> is zero and a program adds X to <code>PROD</code>, Y times we get the result, Options are ⇒ (A) X + Y, (B) XY, (C) X / Y, (D) X - Y, (E) , Leave your comments or Download question paper.

Question is ⇒ If initial value of <code>PROD</code> is zero and a program adds X to <code>PROD</code>, Y times we get the result, Options are ⇒ (A) X + Y, (B) XY, (C) X / Y, (D) X - Y, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	If initial value of `PROD` is zero and a program adds X to `PROD`, Y times we get the result
A.	X + Y [Wrong Answer]
B.	XY [Correct Answer]
C.	X / Y [Wrong Answer]
D.	X - Y [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : B Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ A mod 4 counter will count
from 0 to 4
from 0 to 3
from any number n to n + 4
none of the above

⇒ In a JK flip flop toggle means
set Q = 1 and Q = 0
set Q = 0 and Q = 1
change the output to the opposite state
no change in output

⇒ VSWR can have any value between
0 and 1
- 1 to + 1
0 to ∞
1 to ∞

⇒ Tuned amplifiers are used at radio frequencies.
TRUE
FALSE

⇒ The scaling factor of an MOS device using constant voltage scaling model, the gate area of the device will be scaled as
1/a
1/a²
1/a³
1/a⁴

⇒ The term __________ applies to troposcatter propagation
fading
Faraday rotation
SIDS
atmospheric storms

⇒ A steel bar needs 1200 AT to magnetise it. The voltage that must be applied to the magnetising coil of 100 turns and 10 Ω resistance is __________ volt.
120
12
1200
10

⇒ In a bipolar transistor which current is smallest
collector current
base current
emitter current
any of the three currents

⇒ For an ideal noise free transistor amplifier the noise factor is
zero
zero dB
1 dB
depends on other factors

⇒ For the amplifier in figure, β = 800. The mid-band voltage gain V₀/V_{i0
< 1
≈ 1
800}

⇒ In a 3 phase full converter feeding a highly inductive load, the average load current is 150 A. The peak current through thyristor is
150 A
75 A
50 A
300 A

⇒

Assertion (A): The reverse current in a p-n junction is nearly constant.

Reason (R): The reverse breakdown voltage of a p-n diode depends on the extent of doping.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not a correct explanation of A
A is true but R is false
A is false but R is true

⇒ The colour subcarrier and sidebands produced by its modulation with the chrominance signals are accommodated in the standard channel width by the process of
frequency adjustment
frequency interleaving
frequency changing
frequency amalgamation

⇒ In figure the total inductance of the circui
L₁ + L₂
L₁ + L₂ + M
L₁ + L₂ + 2M
L₁ + L₂ + M

⇒ An homogeneous dielectric material is subjected to an electric field E. If a small cavity is made inside the material, the electric field intensity inside and outside the cavity are different.
TRUE
FALSE

⇒ Which of the following is not a data base function?
DAVERAGE
MAX
DCOUNT
DSTDEV

⇒ A 4 bit synchronous counter uses flip flops with a delay time of 15 ns each. The time required for change of state is
15 ns
30 ns
45 ns
60 ns

⇒ Consider the following statements about conditions that make a metal semiconductor contact rectifying

N type semiconductor with work function φ_s more than work function φ_M of metal
N type semiconductor with work function φ_s less than work function φ_M of metal
P type semiconductor with work function φ_s more than work function φ_M of metal
P type semiconductor with work function φ_s less than work function φ_M of metal.

Of these statements
1 and 3 are correct
2 and 3 are correct
1 and 4 are correct
2 and 4 are correct

⇒ In terms of signum function sgn(t), unit step function u(t) =
1 + sgn(t)
1 - sgn(t)
0.5 + 0.5 sgn(t)
0.5 - 0.5 sgn(t)

⇒ At room temperature, the current in intrinsic semiconductor is due to
holes
electrons
ions
holes and electrons

⇒ A differential amplifier is invariably used in the I/P stage of all OP-amps. This is done basically to produce the OP-amp with a very high.
CMRR
bandwidth
slew rate
open-loop gain

⇒ The poles of an RC function
are simple and lie or negative real axis
are simple and lie on ω axis
must be complex conjugate
may be anywhere on s plane

⇒

Assertion (A): Slotted line is frequently used for microwave measurements.

Reason (R): The unknown impedance is mounted at the end of slotted line.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct but R is wrong
A is wrong but R is correct

⇒ Transconductance indicates the
control of output voltage by input voltage
control of output current by input voltage
control of input voltage by output current
control of input current by input voltage

⇒ The dc output voltage from a power supply
increases with higher values of filter capacitance and decreases with more load current
decreases with higher values of filter capacitance and increases with more load current
decreases with higher values of filter capacitance as well as with more load current
increases with higher values of filter capacitance as well as with more load current

⇒ Consider the following library functions

EXP (i.e., e^x)
ARCTAN (i.e. tan^-1 x)
SQRT (i.e., x)
AES (i.e. |x|)
<
All
1 and 3 only
1, 3, 4 only
1, 2 and 3 only

⇒ Consider following statements : Maximum energy of electrons liberated photoelectrically is independent of light intensity 
Maximum energy of electrons liberated photoelectrically varies nonlinearly with frequency of incident light.

statement (1) is true and (2) is false
statement (1) and (2) both are true
statement (1) is false and (2) is true
statement (1) and (2) both are false

⇒ A MOSFET has a threshold voltage of 1 V and oxide thickness of 500 x 10^-8 [ε_r = 3.9; ε₀ = 8.85 x 10^-14 F/cm, q = 1.6 x 10^-19 c]. The region under the gate is ion implanted for threshold voltage tailoring. The base and type of impant required to shift threshold voltage to - 1 V are __________ .
8.6 x 10¹¹/cm², p-type
8.6 x 10¹¹/cm², n-type
0.86 x 10⁹/cm², p-type
1.02 x 10¹²/cm², n-type

⇒ Which device has one input and many outputs?
Multiplexer
Demultiplexer
Counter
Flip flop

⇒ Secondary emission is always decremental.
TRUE
FALSE









Users Also Read
Previous Papers
Aptitude
Reasoning
Gen.Knowledge
Speak English
English / Verbal
Online / Mock Test
Vedic Math







    
	
	




    
	StudySite.org is world's best free online study content provider, Copyright © 2024 by 
StudySite.org All Rights Reserved