Question is ⇒ If Bmax is the maximum flux density, then eddy cu rrent loss will vary as, Options are ⇒ (A) Bmax, (B) (Bmax)2, (C) (Bmax)1.2, (D) (Bmax)2.4, (E) , Leave your comments or Download question paper.

Question is ⇒ If Bmax is the maximum flux density, then eddy cu rrent loss will vary as, Options are ⇒ (A) Bmax, (B) (Bmax)2, (C) (Bmax)1.2, (D) (Bmax)2.4, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	If B_max is the maximum flux density, then eddy cu rrent loss will vary as
A.	B_max [Wrong Answer]
B.	(B_max)² [Correct Answer]
C.	(B_max)^1.2 [Wrong Answer]
D.	(B_max)^2.4 [Wrong Answer]
View Answer 4 -1 Explanation:- Answer : B Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ In case of a shunt motor if the supply voltage is increased by 10%, which of the following will decrease ?
full load current
full load speed
starting torque
none of the above

⇒ In a D.C. motor, the ratio Eb/Va indicates
running torque of the motor
starting torque of the motor
efficiency of the motor
speed regulation of the motor

⇒ The total losses in a well designed D.C. generator of 10 kW will be nearly
100 W
500 W
1000 W
1500 W

⇒ Which of the following, in a D.C. motor, can sustain the maximum temperature rise ?
Commutator
Armature windings
Slip rings
Field windings

⇒ In a D.C. motor, unidirectional torque is produced with the help of
end plates
bushes
commutator
both (b) and (c)

⇒ If t be the thickness of the laminations, then eddy current loss in a generator. will vary as
¹/_t
¹/_t²
t
t²

⇒ If the terminals of armature of D.C. motor are interchanged, this action will offer following kind of braking
regenerative
plugging
dynamic braking
none of the above

⇒ D.C. series machine has field consisting of
many number of turns of thick wire
many number of turns of thin wire
few number of turns of thick wire
few number of turns of thin wire

⇒ The generated e.m.f. and the current are in the opposite direction in case of
d.c. generators
d.c. motors
both (a) and (b)
none of the above

⇒ In an overloaded motor main danger arises due to
winding getting overheated
busbars getting heated
starter getting damaged
bearings getting overheated

⇒ If B_max is the maximum flux density, then eddy cu rrent loss will vary as
B_max
(B_max)²
(B_max)^1.2
(B_max)^2.4

⇒ The mechanical power developed by a D.C. motor is equal to
power input + losses
back e.m.f. X armature current
power output X losses
power output X efficiency

⇒ While starting a differential compound motor, it is best to short the series field in order to avoid
excessive starting period
motor starting in wrong direction
tripping of the circuit breaker
large in rush of current

⇒ In a D.C. shunt motor, speed is
independent of armature current
directly proportional to the armature current
proportional to the square of the current
inversely proportional to the armature current

⇒ Which of the following loss in a D.C. generator is dissipated in the form of heat ?
Mechanical loss
Core loss
Copper loss
All of the above

⇒ Which loss in a D.C. generator varies with load ?
Copper loss
Eddy current loss
Hysteresis loss
Windage loss

⇒ The plugging gives the
zero torque braking
smallest torque braking
highest torque braking
none of the above

⇒ Which of the following motor is preferred for operation in highly explosive atmosphere ?
Series motor
Shunt motor
Air motor
Battery operated motor

⇒ Which D.C. motor will be suitable alongwith flywheel for intermittent light and heavy loads?
Series motor
Shunt motor
Cumulatively compounded motor
Differentially compounded motor

⇒ Which of the following loss of D.C. motor decreases with increase in load ?
Friction and windage loss
Core loss
Brush contact loss
none of the above

⇒ The armature voltage control of D.C. motor provides
constant torque drive
constant voltage drive
constant current drive
none of the above

⇒ A 230 V D.C. shlint motor takes 32 A at full load. The back e.m.f. on full load, if the resistance of motor armature and shunt field windings are 0.2 Ω and 115 Ω respectively, will be
210 V
215 V
220 V
224 V

⇒ For which application a D.C. motor is preferred over an A.C. motor ?
High speed operation
Low speed operation
Fixed speed operation
Variable speed operation

⇒ In a D.C. generator all of the following could be the effects of iron losses except
Loss of efficiency
Excessive heating of core
Increase in terminal voltage
Rise in temperature of ventilating air

⇒ Which one of the following is not the function of pole shoes in a D.C. machine ?
To reduce eddy current loss
To support the field coils
To spread out flux for better uniformity
To reduce the reluctance of the magnetic path

⇒ Which of the following statement is incorrect ? If a starter is not used with large D.C. motor, it will draw a starting current which
will produce very low starting torque
will produce excessive line voltage drop
will damage the cOmmutator
is many times its full-load current

⇒ Speed ,control by varying the armature circuit resistance, in a D.C. motor, provides a
constant torque drive
variable torque drive
constant power drive
variable power drive

⇒ Where D.C. motor of H.P. 12 or more requires frequent starting, stopping, reversing and speed control
drum type controller is used
three point starter is used
four point starter is used
all above can be used

⇒ Small D.C. motors up to 5 H.P. usually have
2 poles
4 poles
6 poles
8 poles

⇒ In D.C. shunt motors as load is reduced
the speed will increase abruptly
the speed will increase in proportion to reduction in load
the speed will remain almost constant
the speed will reduce