Question is ⇒ If a power cable and a communication cable are to run parallel the minimum distance between the two, to avoid interference, should be, Options are ⇒ (A) 2 cm, (B) 10 cm, (C) 50 cm, (D) 400 cm, (E) , Leave your comments or Download question paper.

Question is ⇒ If a power cable and a communication cable are to run parallel the minimum distance between the two, to avoid interference, should be, Options are ⇒ (A) 2 cm, (B) 10 cm, (C) 50 cm, (D) 400 cm, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	If a power cable and a communication cable are to run parallel the minimum distance between the two, to avoid interference, should be
A.	2 cm [Wrong Answer]
B.	10 cm [Wrong Answer]
C.	50 cm [Correct Answer]
D.	400 cm [Wrong Answer]
View Answer 7 -2 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ A cable carrying alternating current has
hysteresis losses only
hysteresis and leakage losses only
hysteresis, leakage and copper losses only
hysteresis, leakage, copper and friction losses

⇒ In the cables, the location of fault is usually found out by comparing
the resistance of the conductor
the inductance of conductors
the capacitances of insulated conductors
all above parameters

⇒ The current carrying capacity of cables in D.C. is more than that in A.C. mainly due to
absence of harmonics
non-existence of any stability limit
smaller dielectric loss
absence of ripples

⇒ The insulating material for a cable should have
low cost
high dielectric strength
high mechanical strength
all of the above

⇒ The insulating material for cables should
be acid proof
be non-inflammable
be non-hygroscopic
have all above properties

⇒ Which of the following protects a cable against mechanical injury ?
Bedding
Sheath
Armouring
None of the above

⇒ The insulation of the cable decreases with
the increase in length of the insulation
the decrease in the length of the insulation
either (a) or (b)
none of the above

⇒ Is a cable is to be designed for use on 1000 kV, which insulation would you prefer ?
Polyvinyle chloride
Vulcanised rubber
Impregnated paper
Compressed SF6 gas

⇒ In a cable immediately above metallic sheath ____ is provided.
earthing connection
bedding
armouring
none of the above

⇒ In case of three core flexible cable the colour of the neutral is
blue
black
brown
none of the above

⇒ The advantage of oil filled cables is
more perfect impregnation
smaller overall size
no ionisation, oxidation and formation of voids
all of the above

⇒ The bedding on a cable consists of
hessian cloth
jute
any of the above
none of the above

⇒ Capacitance grading of cable implies
use of dielectrics of different permeabilities
grading according to capacitance of cables per km length
cables using single dielectric in different concentrations
capacitance required to be introduced at different lengths to counter the effect of inductance

⇒ Dielectric strength of rubber is around
5 kV/mm
15 kV/mm
30 kV/mm
200 kV/man

⇒ Empire tape is
varnished cambric
vulcanised rubber
impregnated paper
none of the above

⇒ Which of the following insulation is used in cables ?
Varnished cambric
Rubber
Paper
Any of the above

⇒ Pressure cables are generally not used beyond
11 kV
33 kV
66 kV
132 kV

⇒ A certain cable has an insulation of relative permittivity 4. If the insulation is replaced by one of relative permittivity 2, the capacitance of the cable will become
one half
double
four times
none of the above

⇒ PVC stands for
polyvinyl chloride
post varnish conductor
pressed and varnished cloth
positive voltage conductor

⇒ If a cable of homogeneous insulation has a maximum stress of 10 kV/mm, then the dielectric strength of insulation should be
5 kV/mm
10 kV/mm
15 kV/mm
30 kV/mm

⇒ Underground cables are laid at sufficient depth
to minimise temperature stresses
to avoid being unearthed easily due to removal of soil
to minimise the effect of shocks and vibrations due to passing vehicles, etc.
for all of the above reasons

⇒ Copper as conductor for cables is used as
annealed
hardened and tempered
hard drawn
alloy with chromium

⇒ The insulating material should have
low permittivity
high resistivity
high dielectric strength
all of the above

⇒ In a cable, the maximum stress under operating conditions is at
insulation layer
sheath
armour
conductor surface

⇒ Cables for 220 kV lines are invariably
mica insulated
paper insulated
compressed oil or compressed gas insulated
rubber insulated

⇒ In capacitance grading of cables we use a ____ dielectric.
composite
porous
homogeneous
hygroscopic

⇒ The material for armouring on cable is usually
steel tape
galvanised steel wire
any of the above
none of the above

⇒ In cables the charging current
lags the voltage by 90°
leads the voltage by 90°
lags the voltage by 180°
leads the voltage by 180°

⇒ The advantage of cables over overhead transmission lines is
easy maintenance
low cost
can be used in congested areas
can be used in high voltage circuits

⇒ In single core cables armouring is not done to
avoid excessive sheath losses
make it flexible
either of the above
none of the above