Question is ⇒ If 4 quadrant operation is required we need, Options are ⇒ (A) dual converter, (B) full converter, (C) semi converter, (D) none of the above, (E) , Leave your comments or Download question paper.

Question is ⇒ If 4 quadrant operation is required we need, Options are ⇒ (A) dual converter, (B) full converter, (C) semi converter, (D) none of the above, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	If 4 quadrant operation is required we need
A.	dual converter [Correct Answer]
B.	full converter [Wrong Answer]
C.	semi converter [Wrong Answer]
D.	none of the above [Wrong Answer]
View Answer 2 -1 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Find L_eq if each L is
4/3 H
1/3 H
2/3 H
3/2 D

⇒ Which of these has lowest dielectric strength?
Dry air
Wet air
Cotton
Paper

⇒ If current is less than 20 mA and time of contact is very small, the effect of current on human body is likely to be temporary.
TRUE
FALSE

⇒ The divergence of a vector is a scalar, while the curl of a vector is another
scalar
vector
unit vector
none of the above

⇒ As regards BCH code, Hamming code and Reed-Solomon code
BCH and Hamming code are special cases of Reed-Solomon code
Reed-Solomon and Hamming code are special cases of BCH code
BCH and Reed-Solomon code are special case of Hamming code
none of the above

⇒ The speed at which axial electric field due to signal advances in a TWT is equal to
speed of light
(speed of light) (helix pitch helix circumference)
(speed of light) (helix circumference helix pitch)
(speed of light) (helix pitch) (helix circumference)

⇒ The block diagram of the given figure
On-off controller
On-off controller with differential gap
On-off controller with integral gap
Three position controller

⇒ Which of the following antenna is obtained by modifying a waveguide?
Microstrip Antenna
Helical Antenna
Horn Antenna
Dipole Antenna

⇒ Read the following statements about sets

If A and B are sets then A + B denotes union of sets A and B.
The union of A and B is that set whose elements are in either A or B or both.
If A and B are sets, then difference of sets A and B is denoted by A - B.
A - B in the set obtained by removing elements of A from B.

Which of the above are true?
All
1, 2 and 3 only
2 and 3 only
1 and 4 only

⇒ In a push pull circuit
each transistor conducts for 180°
each transistor conducts for more than 180° but less than 360°
each transistor conducts for less than 180°
the period of conduction of each transistor depends on circuit configuration

⇒ How many JK flip-flops are needed to make a 4-bit shift register?
2
4
6
8

⇒ Which of the following is 'synchronous'?
Half adder
Full adder
R-S flip-flop
Clocked R-S flip-flop

⇒ Absolute instruments are used in
laboratories
industries
power houses
standard laboratories

⇒ A 3 phase induction motor is controlled by voltage and frequency control such that the ratio V/f is constant. At 50 Hz, the starting torque is 100 N-m. At 25 Hz, the starting torque
will be less than 100 N-m
will be more than 100 N-m
may be more or less than 100 N-m depending on motor parameters
very small

⇒ Which of the following binary numbers is equivalent to decimal 10?
1000
1100
1010
1001

⇒ The expression given is F(A, B, C, D, E, F, G, H) = Σ(33, 48, 102, 158, 222, 229, 233, 243, 255); then the __________ and __________ minterms are grouped together into dual and variable __________ is reduced using the dual
243, 233, D
222, 158, B
243, 255, A
229, 243, E

⇒ An advantage of memory interlacing is that
a larger memory is obtained
effective speed of memory is increased
cost of memory is reduced
a non-volatile memory is obtained

⇒ Natural commutation can be used in :
DC circuits only
AC circuits only
both AC and DC circuits
none of the above

⇒ Consider the following statements, SWR of a transmission line is infinite when the load is

a short circuit
a complex impedance
an open circuit
a pure reactance

Which of the above statements are correct?
1 and 3 only
1, 2, 3
2, 3, 4
1, 2, 4

⇒ Computers use thousands of flip-flops. To coordinate the overall action, a common signal is sent to all flip-flop known as
debug signal
toggle signal
active signal
clock signal

⇒ When a particular mode is existed in a waveguide, there appears an extra electric component, in the direction of propagation. In what mode is the wave propagating?
Transverse electric
Transverse magnetic
Transverse electromagnetic
Longitudinal

⇒ Permalloy is
a variety of stainless steel
a polymer
a conon-ferrous alloy used in aircraft industry
a nickel an iron alloy having high permeability

⇒ A full wave bridge rectifier is supplied voltage at 50 Hz. The lowest ripple frequency will be
400 Hz
200 Hz
100 Hz
50 Hz

⇒ Consider the following statements regarding the class-B power amplifiers (Complementary symmetry type):

The efficiency of the amplifier is higher than that of class-A amplifier
The power output is low
Crossover distortion is present
The standby power dissipation is absent.

Which of the above statements are correct?
1, 2 and 3
1, 2 and 4
1, 3 and 4
2, 3 and 4

⇒ The resonant frequency of an R_F amplifier is 1 MHz and its bandwidth is 10 kHz. The Q factor will be
10
100
0.01
0.1

⇒ Which of the following, is not a piezoelectric material?
Rochelle salt
Quartz
Lithium sulphate
Sodium bicarbonate

⇒ Many circles are drawn in a Smith chart used for transmission line calculations. The circle shown in the figure represe
unit circles
constant resistance circles
constant reactance circles
constant reflection coefficient circles

⇒ In a series resonant circuit, the resonant frequency is
geometric mean of half power frequencies
arithmetic mean of half power frequencies
difference of half power frequencies
none of the above

⇒ When a ferromagnetic substance is magnetised, there are small changes in its dimensions. This phenomenon is called
hysteresis
magnetostriction
diamagnetism
bipolar relaxation

⇒ In a vibrating reed frequency meter the natural frequency of two adjacent reeds have a difference of
0.25 Hz
0.5 Hz
1.25 Hz
1 Hz