Question is ⇒ Fresh water carrying pipelines in chemical industries are coloured with __________ color., Options are ⇒ (A) sea green, (B) brown, (C) yellow, (D) red, (E) , Leave your comments or Download question paper.

Question is ⇒ Fresh water carrying pipelines in chemical industries are coloured with __________ color., Options are ⇒ (A) sea green, (B) brown, (C) yellow, (D) red, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Fresh water carrying pipelines in chemical industries are coloured with __________ color.
A.	sea green [Correct Answer]
B.	brown [Wrong Answer]
C.	yellow [Wrong Answer]
D.	red [Wrong Answer]
View Answer 8 -3 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The LMTD correction factor (F_T) is defined as the
ratio of true temperature difference to the LMTD.
ratio of LMTD to the true temperature difference.
differenced of true temperature difference and the LMTD.
geometric mean of the true temperature difference and the LMTD.

⇒ Pick out the wrong statement pertaining to shell and tube heat exchanger.
Clearance between shell & baffles and between tube & baffles should be minimum to avoid by-passing of the fluid, but it should be enough to permit the removal of tube bundle.
Baffles are supported independently of the tubes by tie rods and positioned by spacers.
Tie rods are fixed at one end in the tube sheet by making blind holes and the minimum number of tie rods is 4 with at least 10 mm diameter.
Bracket supports are used for horizontal shell, while saddle support is used for vertical shell.

⇒ Apex angle of conical heads used in the bottom heads of chemical process equipments is usually
30°
45°
60°
75°

⇒ A cylinderical pressure vessel of volume 6 πm³ has to be designed to withstand a maximum internal pressure of 10 atm. The allowable design stress of the material is 125N/mm² and corrosion allowance is 2 mm. The thickness of the vessel for a length/diameter ratio of 3 will be close to
5 mm
6 mm
8 mm
10 mm

⇒ Thickness of the frame of a plate and frame filter as compared to that of plates is
less
same
more
either (a) or (b)

⇒ Theoretically calculated diameter of the stripping section of the continuous rectification column is __________ that of the enriching section.
less than
more than
same as
either more or less (depending upon relative volatility)

⇒ Vapor velocity in a distillation column for non-foaming mixture is in the range of __________ times the flooding velocity.
0.1 to 0.3
0.6 to 0.7
0.85 to 0.95
1.5 to 2

⇒ What is the slope of the operating line in the stripping section of a distillation column ?
0
∞
> 1
< 1

⇒ Pick out the wrong statement about the design of seive plate column and the bubble cap column.
The downcomer design and the residence time in the downcomer is almost same for seive plate and bubble cap columns.
Weir length for a bubble cap plate is the same as that for the seive plate.
Weir height for a bubble cap plate column is the same as that for a seive plate column.
Weir height in case of a bubble cap plate ranges from 50 to 150 mm and is higher than the seive plate.

⇒ Hole diameter of the seive trays in the distillation column ranges from __________ mm.
lto3
4 to 8
3 to 12.5
12.5 to 18.5

⇒ A single pass air heater is connected to a two pass unit. For the air flow rate and other conditions remaining the same, the film heat transfer co-efficient for air will vary in the ratio of
2
2^0.8
2^0.2
none of these

⇒ In the downcomer of a distillation column, the minimum recommended residence time is about __________ seconds.
2.5
5
12.5
17.5

⇒ The equivalent diameter for pressure drop is __________ that for heat transfer.
smaller than
greater than
equal to
not related with

⇒ Scale up problem in design based on the similarity concept takes into account __________ similarity.
geometrical
kinematic
dynamic
all (a), (b) and (c)

⇒ Optimum economic pipe diameter for fluid flow is determined by the
viscosity of the fluid.
density of the fluid.
total cost considerations (pumping cost plus fixed cost of the pipe).
none of these.

⇒ In inclined long tube vertical evaporators, the tubes are inclined at an angle of
15°
90°
45°
60°

⇒ Pressure differential maintained across a continuous rotary vacuum filter is in the range of __________ mm Hg column.
50 to 100
100 to 150
250 to 500
600 to 700

⇒ Baffles are provided in a shell and tube heat exchanger to increase the turbulence and velocity of the shell side fluid. Which of the following shaped baffles does not fall in the category of transverse baffle ?
Segmental baffle
Flat plate extending across the wall
Disk type baffle
Helical type baffle

⇒ Compensation against openings in process vessels for giving inlet and outlet connections, for providing sight glasses and manholes etc. is provided for strength and rigidity. The most efficient type of compensation is of __________ type.
nozzle or rim
flared out
fluid in
ring plate

⇒ Pick out the wrong statement.
An air cooled finned pipe is diagram-matically represented by
A heat exchanger is diagrammatically represented by
A 90° welded elbow is diagrammatically represented by
A pipe still heater is diagrammatically represented by

⇒ The ratio for the rate of washing to the final rate of filtration in a washing type of plate and frame filter is
0.25
0.5
0.75
1.25

⇒ In a thin cylindrical shell, the hoop stress is __________ stress.
radial
circumferential tensile
compressive
longitudinal

⇒ Pick out the wrong statement:
The tensile strength of a brittle material is less than its compressive strength.
The compressive strength of a ductile materia] is less than its tensile strength.
In a thick cylindrical shell, the hoop stress is maximum at the inner radius.
The value of crushing load is more than that of buckling load for long colmns.

⇒ Vertical storage vessels are never supported by __________ support.
bracket
saddle
skirt
lug

⇒ In case of 1.5" heat exchanger tubes, the inside flow area __________ with decrease in BWG.
increases
decreases
remains same
none of these

⇒ A head comprises of straight flange section, corner torus, section and central dished section. Crown radius and knuckle radius in a head is related respectively to the
central dished section and corner torus section.
corner torus section and central dished section.
central dished section and straight flange section.
straight flange section and corner torus section.

⇒ The operating pressure drop range in a bag filter is about __________ mm water gauge.
50-150
42865
500-1500
1500-2500

⇒ In packed towers provided with saddle packing, liquid redistributors are positioned at every __________ times column diameter or 6 metres whichever is less.
42769
42863
43023
20-25

⇒ Ratio of tube length to shell diameter for a shell and tube heat exchanger is
8 : 1 to 12 : 1 for both liquid-liquid and gas-gas heat exchangers.
4 : 1 to 8 : 1 for liquid-liquid exchanger.
< 4 : 1 for gas-gas exchangers.
both(b) & (c).

⇒ Minimum recommended baffle spacing in a shell and tube heat exchanger is about (where, D = shell diameter )
0.2 D
0.5 D
0.66 D
0.80 D