Question is ⇒ Four messages band limited to W, W, 2W and 3W respectively are to be multiplex using Time Division Multiplexing (TDM). The minimum bandwidth required for transmission of this TDM signal is, Options are ⇒ (A) W, (B) 3W, (C) 6W, (D) 7W, (E) , Leave your comments or Download question paper.

Question is ⇒ Four messages band limited to W, W, 2W and 3W respectively are to be multiplex using Time Division Multiplexing (TDM). The minimum bandwidth required for transmission of this TDM signal is, Options are ⇒ (A) W, (B) 3W, (C) 6W, (D) 7W, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Four messages band limited to W, W, 2W and 3W respectively are to be multiplex using Time Division Multiplexing (TDM). The minimum bandwidth required for transmission of this TDM signal is
A.	W [Wrong Answer]
B.	3W [Wrong Answer]
C.	6W [Correct Answer]
D.	7W [Wrong Answer]
View Answer 1 -4 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Determine the correctness or otherwise of the following Assertion [a] and the Reason
Both [a] and [r] are true and [r] is the correct reason for [a]
Both [a] and [r] are true but [r] is not the correct reason for [a]
Both [a] and [r] are false
Both [a] and [r] are true

⇒ A PIN diode can be used
as a shunt mounted switch
as a series mounted switch
both as series or shunt mounted switch
non of the above

⇒ A typical microcomputer has 65, 536 registers in its memory. It will be specified as
65.536 memory
65.536 K memory
64 K memory
8 K memory

⇒ In CCIR-B system, the time between start of one H syn. pulse and next is
64 μs
6.4 μs
640 μs
0.64 μs

⇒ Binary multiplication can be done by repeated addition.
TRUE
FALSE

⇒ In phase shift keying the input signal is
s_t(t) = A cos ω₀t and s₂(t) = - A cos ω₀t
s₁(t) = s₂(t) = A cos ω₀t
s₁(t) = A cos ω₀t and s₂(t) = A cos (ω₀t + p/2)
s₁(t) = A cos ω₀t and s₂(t) = - A (cos ω₀t + p/2)

⇒ Which interrupts are masked?
5.5
6.5
7.5
None

⇒ A three terminal monolithic IC regulator can be used as
an a adjustable output voltage regulator alone
an adjustable output voltage regulator & a current regulator
a current regulator & a power switch
a current regulator alone

⇒ The Boolean function A + BC is reduced form of
AB + BC
AB + ABC
(A + B) (A + C)
(A + C)B

⇒ Schmitt trigger can be used as a
comparator
square-wave generator
flip-flop
all of these

⇒

Assertion (A): A class C chopper can operate in first and second quadrants

Reason (R): A class B chopper operates only in second quadrant.

Both A and R are correct and R is correct explanation of A
Both A and R correct but R is not correct explanation of A
A is correct but R is wrong
A is wrong but R is correct

⇒

Assertion (A): The closeness of G(jω) locus to (- 1 + j0) point can be used as a measured of margin of stability.

Reason (R): When the G(jω) locus comes close to encircling (- 1 + j0) point the system becomes oscillatory.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct but R is wrong
R is correct but A is wrong

⇒ Which of the following devices has a silicon dioxide layer?
NPN transistor
Tunnel diode
JFET
MOSFET

⇒ Advanced low power Schottky is a part of
ECL family
CMOS family
TTL family
none of the above

⇒ If C is thermal capacitance, m is mass of liquid and c is specific heat, then
C = mc
c = mC
m = cC
C = (mc)²

⇒ Which statement is correct?
BJT and MOSFET are current controlled devices
BJT is voltage controlled and MOSFET is current controlled device
BJT and MOSFET are voltage controlled devices
BJT is current controlled and MOSFET is voltage controlled device

⇒ Which of the following noise becomes of great importance at high frequencies?
Shot noise
Agitation noise
Flicker noise
Transit time noise

⇒ Which of the following pulse-time modulation is least used?
PDM
PPM
PWM
PAM

⇒ A signal g(t) = A then g(t) is a
energy signal
power signal
neither energy nor power signal
insufficient data

⇒ In a fully controlled bridge converter feeding a resistive load the waveshapes of output voltage and output current
are always similar
can never be similar
may be similar or dissimilar
are similar only if a = 0

⇒ In communication receivers the fidelity is provided by
audio stage
detector range
mixer stage
all of the above

⇒ In telephone, the dial tone has a frequency of
5 Hz
15 Hz
33 Hz
233 Hz

⇒ When a peripheral device is not ready for data transfer it will send to the microprocessor a
low READY bit
high READY bit
low or high READY bit depending on whether input or output is activated
none of the above

⇒ PIL tube means
Picture in Line Tube
Precision in Line Tube
Pairing in Line Tube
Pattern in Line Tube

⇒ In the circuit shown in the figure, the current supplied by the sinusoidal current source
28 A
0.166666666666667
20 A
not determinable from the data given

⇒ Choose the correct match for input resistance of various amplifier configurations shown below configurat
CB-LO, CC-MO, CE-HI
CB-LO, CC-HI, CE-MO
CB-MO, CC-HI, CE-LO
CB-HI, CC-LO, CE-MO

⇒ Flag bits in arithmetic unit provide
status type information
repeatability
facilities for rechecks
all of the above

⇒ Vidicon and plumbicon operate on the principle of
photo conduction
photo emission
photo voltaic
none of the above

⇒ ROC of sequence x[n] = (3)ⁿ ∪[n] + (4)ⁿ ∪[- n - 1]
|z| > 4
3 < |z| < 4
|z| < 4
|z| > 3

⇒ All digital circuits can be realised using only
EX-OR gates
Multiplexers
Half adders
OR gates