Question is ⇒ For which of the following applications 'D.C. motors are still preferred ?, Options are ⇒ (A) High efficiency operation, (B) Reversibility, (C) Variable speed drive, (D) High starting torque, (E) , Leave your comments or Download question paper.

Question is ⇒ For which of the following applications 'D.C. motors are still preferred ?, Options are ⇒ (A) High efficiency operation, (B) Reversibility, (C) Variable speed drive, (D) High starting torque, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	For which of the following applications 'D.C. motors are still preferred ?
A.	High efficiency operation [Wrong Answer]
B.	Reversibility [Wrong Answer]
C.	Variable speed drive [Correct Answer]
D.	High starting torque [Wrong Answer]
View Answer 2 -3 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Which of the following happens when star-delta starter is used ?
Starting voltage is reduced
Starting current is reduced
Both (a) and (b)
None of the above

⇒ Which of the following alternatives will be cheaper ?
A 100 H.P. A.C. three phase motor
Four motors of 25 H.P. each
Five motors of 20 H.P. each
Ten motors of 10 H.P. each

⇒ The size of an excavator is usually expressed in terms of
crowd' motion
angle of swing
cubic metres
travel in metres

⇒ Reluctance motor is a ____
variable torque motor
low torque variable speed motor
self starting type synchronous motor
low noise, slow speed motor

⇒ ____ has the least value of starting torque to full load torque ratio.
D.C. shunt motor
D.C. series motor
Squirrel cage induction motor
Slip ring induction motor

⇒ Which of the following motors is usually preferred for kiln drives ?
Cascade controlled A.C. motor
Slip ring induction motor
Three phase shunt wound commutator motor
Any of the above

⇒ For blowers which of the following motors is preferred ?
D.C. series motor
D.C. shunt motor
Squirrel cage induction motor
Wound rotor induction motor

⇒ ____ is preferred for synthetic fibre mills.
Synchronous motor
Reluctance motor
Series motor
Shunt motor

⇒ ____ is not a part of ball bearing ?
Inner race
Outer race
Cage
Bush

⇒ In ____ method of starting three phase induction motors the starting voltage is not reduced.
auto-transformer
star-delta
slip ring
any of the above

⇒ Which of the following motors has series characteristics ?
Shaded pole motor
Repulsion motor
Capacitor start motor
None of the above

⇒ Light duty cranes are used in which of the following ?
Power houses
Pumping stations
Automobile workshops
All of the above

⇒ Rotor of a motor is usually supported on____ bearings.
ball or roller
needle
bush
thrust

⇒ The starting torque of a D.C. motor is independent of which of the following?
Flux
Armature current
Flux and armature current
Speed

⇒ In case of ____ speed control by injecting e.m.f. in the rotor circuit is possible.
d.c. shunt motor
schrage motor
synchronous motor
slip ring induction motor

⇒ Which of the following machines has heavy fluctuation of load ?
Printing machine
Punching machine
Planer
Lathe

⇒ The characteristics of drive for crane hoisting and lowering are which of the following ?
Precise control
Smooth movement
Fast speed control
All of the above

⇒ While selecting an electric motor for a floor mill, which electrical characteristics will be of least significance ?
Running characteristics
Starting characteristics
Efficiency
Braking

⇒ Ward-Leonard controlled D.C. drives are generally used for ____ excavators.
Light duty
Medium duty
Heavy duty
All of the above

⇒ Which of the following is essentially needed while selecting a motor ?
Pulley
Starter
Foundation pedal
Bearings

⇒ The selection of an electric motor for any application depends on which of the following factors ?
Electrical characteristics
Mechanical characteristics
Size and rating of motors
Cost

⇒ In series motor which of the following methods can be used for changing the flux per pole ?
Tapped field control
Diverter field control
Series-parallel control
Any of the above

⇒ Battery operated scooter for braking uses
plugging
mechanical braking
regenerative braking
rheostatic braking

⇒ In a paper mill where constant speed is required
synchronous motors are preferred
A.C. motors are preferred
individual drive is preferred
group drive is preferred

⇒ The starting torque in case of centrifugal pumps is generally
less than running torque
same as running torque
slightly more than running torque
double the running torque

⇒ ____ has least range of speed control.
Slip ring induction motor
Synchronous motor
D.C. shunt motor
Schrage motor

⇒ Which feature, while selecting a,motor for centrifugal pump, will be of least significance ?
Starting characteristics
Operating speed
Horse power
Speed control

⇒ Which of the following motors is used for elevators ?
Induction motor
Synchronous motor
Capacitor start single phase motor
Any of the above

⇒ Which part of a motor needs maximum attention for maintenance ?
Frame
Bearing
Stator winding
Rotor winding

⇒ While selecting motor for an air conditioner which of the following characteristics is of great importance ?
Type of bearings
Type of enclosure
Noise
Arrangement for power transmission