Question is ⇒ For what positive value of K does the polynomial s4 + 8s3 + 24s2 + 32s + K have roots with zero real parts?, Options are ⇒ (A) 10, (B) 20, (C) 40, (D) 80, (E) , Leave your comments or Download question paper.

Question is ⇒ For what positive value of K does the polynomial s4 + 8s3 + 24s2 + 32s + K have roots with zero real parts?, Options are ⇒ (A) 10, (B) 20, (C) 40, (D) 80, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	For what positive value of K does the polynomial s⁴ + 8s³ + 24s² + 32s + K have roots with zero real parts?
A.	10 [Wrong Answer]
B.	20 [Wrong Answer]
C.	40 [Wrong Answer]
D.	80 [Correct Answer]
View Answer 3 -4 Explanation:- Answer : D Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒

Assertion (A): Moving iron instrument can be used on ac or dc.

Reason (R): In a moving iron instrument deflecting torque is proportional to square of current.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not correct explanation of A
A is true R is false
A is false R is true

⇒ Consider a 565 PLL with R_T = 10 kΩ and C_T = 0.01 μF. What is the output frequency of the VCO?
10 kHz
5 kHz
2.5 kHz
1.25 kHz

⇒ In a specimen of silicon steel, a field strength of 200 A/m causes a flux density of 0.5 T. In a specimen of cast iron, the same H would cause B to be
0.5 T
less than 0.5 T
more than 0.5 T
0.5 T or more or less

⇒ In a 100% amplitude modulated signal, the power in the upper sideband when carrier power is to be 100 W and modulation system SSBSC, is
100 W
66 W
50 W
25 W

⇒ Binary 101010 is equivalent to decimal number
24
42
44
64

⇒ In a pulsed RADAR typical value of pulse duration and pulse frequency respectively are
1 μs and 50 Hz
1 μs and 500 Hz
4 μs and 50 Hz
4 μs and 500 Hz

⇒ The main difference between the broadside arrays and end fire arrays is that
individual elements are fed with same current in broadside arrays and of different magnitude in end fire arrays
in broadside arrays the elements are equidistant whereas in end fire array the distance between elements increases progressively
the total number of elements in broadside array is always one and a half times that of elements in end fire arrays
in broadside array the individual elements are fed in, out of phase by 180° whereas in end fire array individual elements are fed with currents of equal magnitude but their phases vary progressively along the line in such a way as to make the entire arrangement substantially unidirectional

⇒ Let JCOKE = 3 and LPEPSI = 5. Consider the statement 8
1
15
10

⇒ The input to negative clamper has a peak value of V_p. Then in the output the positive and negative peaks are nearly
0 and -2 V respectively
V_p and -V_p respectively
2 V_p and 0 respectively
none of the above

⇒

Match the following:

	List I		List II
A.	Ring modulator	1.	Clock recovery
B.	VCO	2.	Demodulation of FM
C.	Foster Seeley discriminator	3.	Frequency conversion
D.	Mixer	4.	Summing of two points
		5.	Generation of FM
		6.	Generation of DSB-SC

A-1, B-3, C-2, D-4
A-6, B-5, C-2, D-3
A-6, B-1, C-3, D-2
A-5, B-6, C-1, D-3

⇒

Match the following:

	List I (Form)		List II (Network)
A.	Cauer I	1.	L in series arm and C in shunt arm of ladder
B.	Cauer II	2.	C in series arm and L in shunt arm of ladder
C.	Foster I	3.	Series combination of L and C in parallel
D.	Foster II	4.	Parallel combination of L and C in series

A-1, B-2, C-3, D-4
A-1, B-2, C-4, D-3
A-2, B-1, C-4, D-3
A-2, B-1, C-3, D-4

⇒ In which of the following logical group instructions of 8085 is the addressing mode 'immediate'?
ANA r
ANA M
ANI data
XRA r

⇒ The region between a pin of parallel perfectly conducting planes of infinite extent is y and z directions is partially filled with a dielectric as shown be
-2
2
0
1

⇒ The upper and lower side frequencies for 3 kHz audio modulation with a 27 MHz carrier frequency will be
30 and 24 MHz
27.3 and 26.7 MHz
27.3 and 26.97 MHz
27.3 and 26.97 MHz

⇒ The signal define by the equations u(t - a) = 0 for t < a and u(t - a) = 1 for t ≥ a is
a unit step function
a shifted unit step function orginating at t = a
a pulse function
none of the above

⇒ At room temperature, the current in intrinsic semiconductor is due to
holes
electrons
ions
holes and electrons

⇒ The minimum value of h_fe of a transistor used in RC phase shift oscillator is
54.4
45.4
44.5
29

⇒ What will be the maximum conversion time in 6 bit dual slope A/D converter uses a reference of -6v and a 1 MHz clock. It uses a fixed count of 40 (101000).
108 sec
63 μ sec
40 sec
80 μ sec

⇒ Program counter in a digital computer
counts the number of programs run in the machine
counts the number of times a subroutine
counts the number of time the loops are executed
points the memory address of the current or the next instruction

⇒ Strip lines are used at
microwave frequency
low frequency
High frequency
at any frequency

⇒ In a single phase full wave regulator feeding R-L load, short gate pulse are not suitable.
TRUE
FALSE

⇒ The resistance of human body is about
5000 Ω
2000 Ω
1000 Ω
200 Ω

⇒ To bypass a 100 ohm emitter resistor at
10 μF
100 μF
1000 μF
1 μF

⇒ The impedance 3.2 - j 12 in polar form is given as
6.4 ∠ - 75°
8.4 ∠ - 75°
10.4 ∠ - 75°
12.4 ∠ - 75°

⇒ A 6 bit R-2R ladder D/A converter has a reference voltage of 6.5 V. It meets standard linearity then resolution in percent and volts.
3% 7 V
6.4 V, 2%
0.1%, 1.57 V
1.57%, 0.1 V

⇒ Binary storage of decimal number 44 in 8 bits is
101100
10101100
10101101
101101

⇒ In figure v₁ = 8 V and v₂ = 8 V. Which diode will cond
D₁ only
D₂ only
Both D₁ and D₂
Neither D₁ nor D₂

⇒ For a system to work, as oscillator the total phase shift of the loop gain must be equal to
90°
45°
270°
360°

⇒ When electronic emission occurs due to bombardment of high velocity electrons on a metal surface, it is called secondary emission.
TRUE
FALSE

⇒ A 200 turn coil has a self inductance of 10 mH. If the number of turns is doubled, all other quantities remaining the same, the self inductance will be
2.5 mH
5 mH
20 mH
40 mH