Question is ⇒ For the system in the given figure G varies slightly, the ratio of open loop sensitivity to closed loop sensitivit, Options are ⇒ (A) 1 : (1 + GH), (B) 1 : (1 + GH)-1, (C) 1 : (1 - GH), (D) 1 : (1 - GH)-1, (E) , Leave your comments or Download question paper.

Question is ⇒ For the system in the given figure G varies slightly, the ratio of open loop sensitivity to closed loop sensitivit, Options are ⇒ (A) 1 : (1 + GH), (B) 1 : (1 + GH)-1, (C) 1 : (1 - GH), (D) 1 : (1 - GH)-1, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	For the system in the given figure G varies slightly, the ratio of open loop sensitivity to closed loop sensitivit
A.	1 : (1 + GH) [Wrong Answer]
B.	1 : (1 + GH)^-1 [Correct Answer]
C.	1 : (1 - GH) [Wrong Answer]
D.	1 : (1 - GH)^-1 [Wrong Answer]
View Answer 1 -2 Explanation:- Answer : B Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ EPROM can be
UVPROM
EEPROM
both UVPROM and EEPROM
none of the above

⇒ In audio cassettes the width of each recording track is
5 mm
2.5 mm
1.5 mm
1 mm

⇒ In a series RLC circuit, the current at resonance is I₀ the total energy stored in the circuit at resonance is
LI₀²
2 LI₀²
2 LI₀²
0.5 LI²

⇒

Assertion (A): Thevenin's theorem helps us to find current in a branch of a network for different values of impedances of that branch.

Reason (R): Thevenin's equivalent circuit replaces a network by a voltage source in series with impedance.

Both A and R are true and R is correct explanation of A
Both A and R are true and R is not the correct explanation of A
A is true but R is false
A is false but R is true

⇒ In a single-stage RC coupled common emitter amplifier, the phase shift at the lower 3 dB frequency is
zero
135°
180°
225°

⇒ Which of the following parameters is negligible in transmission lines?
R
L
C
G

⇒ Which of the following is a digital modulation technique?
PCM
PSK
DM
All

⇒ When a peripheral device is not ready for data transfer it will send to the microprocessor a
low READY bit
high READY bit
low or high READY bit depending on whether input or output is activated
none of the above

⇒ Volume control found on the front panel of television receivers
a ganged resistor
a variable resistor of logarithmic type
a variable resistor of linear type
a trimmer potentiometer

⇒ The initial contents of the 4 bit serial in parallel out right shift, shift register shown in figure is 0110. After three clock pulses are applied, the contents of the shift register wil
0
101
1010
1111

⇒ In C-language f- = 9 is equivalent to
f = -9
f = f - 9
f = 9 - 1
-f = 9

⇒ For the given truth table, the correct Boolean expressio
XYZ + X YZ + X Y Z
X Y Z + XYZ + X YZ
X Y Z + XYZ + XY Z
XYZ + XYZ + XY Z

⇒ System bus is the communication channel between microprocessor and peripherals.
TRUE
FALSE

⇒ To find current in a resistance connected in a network, Thevenin's theorem is used V_TH = 20 V and R_TH = 5 Ω. The current through the resistance
is 4 A
is 4 A or less
is less than 4 A
may be 4 A or less or more than 4 A

⇒ If X(z) = (1 - az^-1)^-1 and |a| < |z|, the initial value x₀ = 0
TRUE
FALSE

⇒ The current through R₁ is(If β = 99, V_BE = 0.7
0.1 mA
0.35 mA
0.2 mA
none

⇒ To draw ac equivalent circuit for a CE amplifier we should
Reduce all dc sources to zero
Short all capacitors
Reduce all dc sources to zero and short all capacitors
Reduce all dc sources to zero and open all capacitors

⇒ A 2 bit BCD D/A converter is a weighted resistor type with E_R = 1V, R = 1 MΩ and R_f = 10KΩ then Resolution in percent and volt is __________ .
1%, 1 mv
10%, 10 mv
10%, 1 mv
1%, 10 mv

⇒ A conductor is said to be perfect if it has __________ conductivity
finite
infinite
unity
zero

⇒ A network has only independent current sources and resistance. If values of all resistors are doubled, the values of node voltages
will become half
will remain unchanged
will become double
cannot be determined unless circuit configuration and values of resistors are known

⇒ The following components are used to measure power output of a 2 kW TWT amplifier:

TWTA
Low pass/high pass filter
20 dB attenuator
40 dB directional complex with matched load
Power load

What is the correct sequence of connection of these components?
2 - 4 - 1 - 3 - 5
1 - 3 - 4 - 2 - 5
1 - 2 - 4 - 3 - 5
2 - 4 - 1 - 5 - 3

⇒ A class A chopper has an input voltage of 200 V. T_on = 1.5 ms and T_off = 4.5 ms. The duty cycle, average output voltage and ripple factor respectively are
0.5, 100 V and 1
0.25, 50 V and 3
0.25, 50 V and 1
0.5, 100 V and 3

⇒ In a klystron amplifier the transit time of electron passing the gap in the cavity should be
less than one cycle
less than half cycle
less than quarter cycle
more than quarter cycle

⇒ An engineer designs an amplifier to have a voltage gain of 60, but when constructed it only had a gain of 50. Which of the following will increases from this type of operation?
Stability
Bandwidth
Distortion
Input resistance

⇒ In ferromagnetic materials, the orientation between neighbouring permanent dipoles is parallel.
TRUE
FALSE

⇒ The oscillator shown in figure
Clapp oscillator
R-C Phase shift oscillator
Hartley oscillator
Colpitt's oscillator

⇒ Current derating may be necessary when thyristors are operating in
series
parallel
series or parallel
none of the above

⇒ Which of the following amplifier circuit using junction transistor has the best gain?
Common base
Common emitter
Common collector
All have the same gain

⇒ Kelvin's double bridge is used to measure low resistances because
it has high sensitivity
there is no thermoelectric emf
resistance variation due to temperature
effect of contact and lead resistances is eliminated

⇒ Find 'X' in the circuit bel
p(0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 15)
0
Σ(14)
1