Question is ⇒ For the high-pass circuit to act as a differentiator, the time constant must be, Options are ⇒ (A) small, (B) very small in comparison to the time period of the input signal, (C) very high in comparison to the time period of the input signal (that is low pass circuit), (D) moderate value, (E) , Leave your comments or Download question paper.

Question is ⇒ For the high-pass circuit to act as a differentiator, the time constant must be, Options are ⇒ (A) small, (B) very small in comparison to the time period of the input signal, (C) very high in comparison to the time period of the input signal (that is low pass circuit), (D) moderate value, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	For the high-pass circuit to act as a differentiator, the time constant must be
A.	small [Wrong Answer]
B.	very small in comparison to the time period of the input signal [Correct Answer]
C.	very high in comparison to the time period of the input signal (that is low pass circuit) [Wrong Answer]
D.	moderate value [Wrong Answer]
View Answer 1 -3 Explanation:- Answer : B Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Consider the following

Generation of SSB signals
Design of minimum phase type filters
Representation of band pass signals

Which of the above applications is Hilbert transform used?
1 only
1, 2 and 3
1, 2 only
1 and 3

⇒

Assertion (A): In 8085 SP and PC are 8 bit each.

Reason (R): 8085 is an 8 bit microprocessor.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct R is wrong
A is wrong R is correct

⇒ In a CE amplifier circuit, the output voltage
is very small
is always constant
depends on β
none of the above

⇒ An engineer designs an amplifier to have a voltage gain of 60, but when constructed it only had a gain of 50. What percentage of feedback will cause oscillations?
0.001
0.005
0.01
0.02

⇒ The modulation index is, if f_m = 500 Hz, Δf = 2.25 kHz
2.25
4.5
9
18

⇒ In the given figure, A = B = 1 and C = D = 0. Then
1
0
either 1 or 0
indeterminate

⇒ Figure repres
Integrator
Differentiator
High Pass Filter
Band Pass Filter

⇒ For the system in the given fi
y_k = u_k + 0.5 y_{k - 2}
y_k = u_k + 0.5 u_{k - 2}
y_k = u_k - 0.5 y_{k - 2}
y_k = u_k - 0.5 u_{k - 2}

⇒ In a N-P-N transistor, when emitter junction is forward biased and collector junction is reverse biased the transistor will operate in
active region
saturation region
cut-off region
inverted region

⇒ The pre-emphasis in FM aids in providing extra noise immunity by
emphasizing only the higher frequency components
emphasizing the entire frequency band
emphasizing only the lower frequency band
cutting down the low frequency noise

⇒ The current wave in figure is passed through 3 H inductor. The voltage across inductance during the period 2 < t < 3 second
12 V
- 12 V
6 V
- 6 V

⇒ A Shockley diode can be used
in place of SCR
as a trigger switch for SCR
in place of UJT
both in place of SCR and as a trigger switch for SCR

⇒ δ(t) is a
energy signal
power signal
neither energy nor power
none

⇒ Which dc servomotor requires strongest permanent magnet?
Slotted armature
Surface wound armature
Surface wound with stationary rotor
Either (a) or (b)

⇒ The resistance of a metallic wire would
increase as f increase
decrease as f increase
remains the same at all frequencies
increase with f up to a certain frequency and then decrease

⇒

Assertion (A): Capacitance of a solid conducting spherical body of radius 'a' is given by 4 pε₀a in free space.

Reason (R): Δ x H = jωεE + J.

Both A and R are individually true and R is the correct explanation of A
Both A and R are individually true but R is not the correct explanation of A
A is true but R is false
A is false but R is true

⇒ The following table gives some time functions and the Laplace transf
2 and 4
1 and 4
3 and 4
1 and 2

⇒ In a biased JFET (Figure) the shape of the channel is as shown bec
it is the property of material used
the drain end is more reverse biased than source end
drain end is more forward biased than source end
impurity profile changes with distance

⇒ Which one of the following is loaded in the main memory by the bootstrap loader?
System data
User program
BIOS
Part of DOS

⇒ An amplifier has open loop gain of 100, input impedance 1 kΩ and output impedance 100 Ω. If negative feedback with β = 0.99 is used, the new input and output impedances are
10 Ω and 1 Ω
10 Ω and 10 kΩ
100 kΩ and 1 Ω
100 kΩ and 10 Ω

⇒ A magnetron has a cylindrical cathode surrounded by an anode structure having cavities opening into interaction space by means of slots
TRUE
FALSE

⇒ A BJT amplifier has a power gain of 0.5 from source to base. The power gain in dB is
-0.3 dB
-3 dB
-6 dB
-10 dB

⇒ The class of insulation of impregnated paper is
A
B
C
F

⇒ Which one is a linear system?
y[n] = x[n] x x[n - 1]
y[n] = x[n] + x[n - 10]
y[n] = x²[n]
(a) and (c)

⇒ The width of a radio beam from a 1 m diameter parabolic antenna at 10 GHz is about
100°
50°
5°
1°

⇒

Assertion (A): In digital communication data is coded prior to being transferred.

Reason (R): A number of codes for digital data processing are available.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct but R is wrong
A is wrong but R is correct

⇒ Vectored interrupt is an interrupt that takes the program to a vector location. TRAP vectors to 0024 FI, RST 7.5 to 003 CH, RST 6.5 to 0034 H and
RST 5.5
RST 6.5
24 H to 48 H
RST 5.5 to 002 CH

⇒ Consider the following expressions which indicate the step or impulse response of an initially relaxed system

[5 - 4 e^-2t] u(t)
[e^-2t + 5] u(t)
d(t) + 8 e^-2t u(t)
d(t) + 4 e^-2t u(t)

Those which correspond to the step and impulse response of the same system include
1 and 3
1 and 4
2 and 4
2 and 3

⇒ The temperature coefficient of resistance for a thermistor is
low and negative
low and positive
high and negative
high and positive

⇒ In figure, I_C &as
I₁
I_B
0.5 I₁
0.5 I_B