Question is ⇒ For the amplifier in figure, β = 800. The mid-band voltage gain V0/Vi</sub, Options are ⇒ (A) 0, (B) < 1, (C) ≈ 1, (D) 800, (E) , Leave your comments or Download question paper.

Question is ⇒ For the amplifier in figure, β = 800. The mid-band voltage gain V0/Vi</sub, Options are ⇒ (A) 0, (B) < 1, (C) ≈ 1, (D) 800, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	For the amplifier in figure, β = 800. The mid-band voltage gain V₀/V_i
A.	0 [Wrong Answer]
B.	< 1 [Wrong Answer]
C.	≈ 1 [Correct Answer]
D.	800 [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ In the saturation region of CE output characteristics of n-p-n transistor, V_CE is about
0.5 V
15 V
- 0.5 V
- 15 V

⇒ The sum of positive real function is positive real.
TRUE
FALSE

⇒ A rare gas having N atoms/m³ is subjected to an electric field E. The electric dipole moment per unit volume is proportional to N and E.
TRUE
FALSE

⇒

Assertion (A): A self bias circuit is the most commonly used bias circuit for bipolar junction transistors

Reason (R): A self bias circuit limits the increase in collector or emitter current due to change in junction temperature.

Both A and R are correct and R is correct explanation for A
Both A and R are correct but R is not correct explanation for A
A is correct R is wrong
A is wrong R is correct

⇒ If a zero is added to a second order underdamped system
the peak overshoot is increased
the peak overshoot is decreased
the peak overshoot remains unchanged
either (a) or (b)

⇒ A Schottky diode clamp is used along with switching BJT for
reducing the power dissipation
reducing the switching time
increasing the value of β
reducing the base current

⇒ Temperature is analogous to
voltage
flux
charge
none of the above

⇒

Assertion (A): At a temperature of 1000 K, thermionic emission current is about 0.1 A/cm² of surface.

Reason (R): Thermionic emission current is given by I_th = SA₀ T² e^-Ew/kT.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not correct explanation of A
A is true but R is false
A is false but R is true

⇒ The main advantage of CMOS circuit is
high gain
high output impedance
low power consumption
high gain and high output impedance

⇒ In n type MOSFET, the substrate
is p type
is n type
is metallic
may be p or n type

⇒ Which of the following is not a data base function?
DAVERAGE
MAX
DCOUNT
DSTDEV

⇒ A magnetic circuit has an iron length of 20 cm and air gap length 0.1 cm. If μ_r = 200 then
mmf for iron and air gap are equal
mmf for iron is much less than that for air gap
mmf for iron is much more than that for air gap
either (a) or (c)

⇒

Assertion (A): Microprocessor 8085 has an 8 bit register called accumulator which stores intermediate answers during a computer operation.

Reason (R): Accumulator can send or receive data.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct R is wrong
A is wrong R is correct

⇒

Assertion (A): Shunt of an ammeter has a low resistance.

Reason (R): Shunt may be connected in series or in parallel with ammeter.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not correct explanation of A
A is true R is false
A is false R is true

⇒ In figure, the switch is closed at t = 0. At t = 0⁺ The value of current supplied by batter
0.0416666666666667
0.0833333333333333
zero
infinity

⇒ The bandwidth of DSB suppressed carrier modulation system when the modulating frequency varies between 500 Hz and 5 kHz is
555 kHz
505 kHz
500 kHz
9 kHz

⇒ A 1 kHz sinusoidal signal is ideally sampled at 1500 samples/sec and the sampled signal is passed through an ideal low pass filter with cut off frequency 800 Hz. The output signal has the frequency.
0 Hz
0.75 kHz
0.5 kHz
0.25 kHz

⇒ Which of the following statement is correct?
A FET is a current controlled device
A BJT is always reverse biased
The semi-conductor material of the gate in an N-channel JFET is p-type
JFET has higher input impedance than MOSFET

⇒ The power factor at the input terminals of a cyclo- converter is generally
low and leading
low and lagging
high and leading
high and lagging

⇒ A single phase semiconverter is supplying RLE load and has a freewheeling diode across the load. The firing angle is a. The freewheeling diode conducts for
a° in each half cycle
(p - a)° in each cycle
a° in one full cycle
(p + a)° in each half cycle

⇒ Modulation is also called detection.
TRUE
FALSE

⇒ A 3 bit binary adder can add
2 bits
2 bits
3 bits
8 bits

⇒ Line of sight transmission is used in
radio frequencies below 1 MHz
VHF only
audio signals only
VHF and UHF

⇒ Find R_TH across the terminals A a
52.28 Ω
58.28 Ω
52.82 Ω
58.82 Ω

⇒ In C the range of real constants expressed in exponential form is
-2.3 e 37 to + 2.3 e 37
-3.4 e 38 to + 3.4 e 38
-3.4 e 37 to + 3.4 e 37
-2.3 e 38 to + 2.3 e 38

⇒ Consider the following statements as regards noise

If Gaussian noise is applied at input of a rectifier, the output is not gaussian
The noise encountered on a telephone line consists of short, pulse type disturbances whose amplitude distribution is not Gaussian
Shot noise results from random emission of electrons from a cathode
Shot noise results from phenomenon associated with the flow of current across semi conductor junctions

Which of the above are correct?
1, 2, 3, only
1, 2, 4 only
1, 2, 3, 4
2, 3 only

⇒

Assertion (A): If the duty cycle of chopper is low the current would not become discontinuous

Reason (R): If the time constant L/R of the load in chopper is low the current may become discontinuous.

Both A and R are correct and R is correct explanation of A
Both A and R correct but R is not correct explanation of A
A is correct but R is wrong
A is wrong but R is correct

⇒ Some sources of TV programs are

TV camera
Telecine
VTR
External signal

Which of the above are actually present in a TV studio?
1, 2, 3 and 4
1, 2, 3
1 and 3
1 2 and 4

⇒ In a JK flip flop toggle means
set Q = 1 and Q = 0
set Q = 0 and Q = 1
change the output to the opposite state
no change in output

⇒ The two port networks are connected in cascade, the combination is to be represented as a single two-Port network. The parameters of the network are obtained by multiplying the individual matrix
z-parameter
h-parameter
y-parameter
ABCD parameter