Question is ⇒ For steel members not exposed to weather, the thickness of steel should not be less than., Options are ⇒ (A) 4.5 mm, (B) 6 mm, (C) 8 mm, (D) 10 mm, (E) , Leave your comments or Download question paper.

Question is ⇒ For steel members not exposed to weather, the thickness of steel should not be less than., Options are ⇒ (A) 4.5 mm, (B) 6 mm, (C) 8 mm, (D) 10 mm, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	For steel members not exposed to weather, the thickness of steel should not be less than.
A.	4.5 mm [Wrong Answer]
B.	6 mm [Correct Answer]
C.	8 mm [Wrong Answer]
D.	10 mm [Wrong Answer]
View Answer 65 -10 Explanation:- Answer : B Discuss it below : Hemant kumar Said on 2017-12-27 23:06:52 Sager ## 4.5 is when secondary member 6mm for main mambe(both are not exposed to weather) Sagar Said on 2017-11-12 23:33:01 option A is correct exposed to weather 6mm with painting and 8 mm without painting not exposed to weather 4.5mm !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The minimum width B of a solid casing for a cased beam, is equal to.
B = b + 25 mm
B = b + 50 mm
B = b + 75 mm
B = b + 100 mm

⇒ The live load for a sloping roof with slope 15°, where access is not provided to roof, is taken as
0.65 kN/m2
0.75 kN/m2
1.35 kN/m2
1.50 kN/m2

⇒ The effective length of a fillet weld should not be less than
two times the weld size
four times the weld size
six times the weld size
weld size

⇒ The bridge having its floor supported at the top structure is called
Through bridge
Semi-through bridge
Deck bridge
Over bridge

⇒ Select the correct statement
Material cost of a rivet is higher than that of a bolt.
Tensile strength of a bolt is lesser than that of a rivet.
Bolts are used as a temporary fastenings whereas rivets are used as permanent fastenings.
Riveting is less noisy than bolting.

⇒ According to IS Specifications, the effective length of a column effectively held in position at both ends and restrained in direction at one end is taken as
0.67 L
0.8 L
L
1.5 L

⇒ According to IS: 800-1962, the coefficient of expansion of steel per degree centigrade per unit length, is taken as.
0.000008
0.000010
0.000012
0.000014

⇒ The range of economical spacing of trusses varies from
L/3 to L/5
L/4to2L/5
L/3 to L/2
2L/5 to 3L/5 where L is span

⇒ When plates are exposed to weather, tacking rivets are provided at a pitch in line not exceeding (where t is the thickness of the outside plate).
8 t
16 t
24 t
32 t

⇒ The maximum permissible span of asbestos cement sheets is
650 mm
810 mm
1250 mm
1680 mm

⇒ Horizontal stiffener in a plate girder is provided to safeguard against
shear buckling of web plate
compression buckling of web plate
yielding
all of the above

⇒ Load factor is
always equal to factor of safety
always less than factor of safety
always greater than factor of safety
sometimes greater than factor of safety

⇒ As per IS 800-1984 the minimum pitch of rivets in a row is recommended as diameter of the rivet times
2.0
2.5
3.0
4.0

⇒ Trussed bridges are usually constructed as
Deck bridges
Through bridges
Semi-through bridges
Any type of bridge

⇒ The load on a lintel is assumed as uniformly distributed if the height of the masonry above it, is upto a height of.
the effective span
1.25 times the effective span
1.50 times the effective span
2.0 times the effective span

⇒ The maximum value of slenderness ratio of compression members carrying loads resulting from dead loads and superimposed load is
100
180
150
200

⇒

In rolled steel beams, shear force is mostly resisted by.

web only
flanges only
web and flanges together
none of these.

⇒ The thickness of the web of a mild steel plate girder is less than d/200. If only one horizontal stiffener is used, it is placed at.
the neutral axis of the section
2/3rd of the depth of the neutral axis from the compression flange
2/5th of the depth of the neutral axis from the compression flange
2/5th of the height of the neutral axis from tension flange

⇒ For the steel member exposed to weather and accessible for repainting, the thickness of steel should not be less than (excepting the webs of Indian Standard rolled steel joists and channels).
4 mm
6 mm
8 mm
10 mm

⇒ The pair of walls constructed on both sides of abutments to retain the earth banks are called
Wing walls
Breast walls
Retaining walls
Curtain walls

⇒ Size of rivet is specified by
Shape
Diameter of head
Shank diameter
Weight

⇒ Design of a riveted joint, is based on the assumption:
Load is uniformly distributed among all the rivets
Shear stress on a rivet is uniformly distributed over its gross area
Bearing stress in the rivet is neglected
All the above.

⇒ Rocker bearings are suitable for span
Less than 8 m
Upto 12 m
12 to 20 m
More than 20 m

⇒ The minimum thickness of a steel plate, which is directly exposed to weather and is not accessible for cleaning and repainting, should be:
4.5 mm
6 mm
8 mm
10 mm

⇒ According to IRC recommendations the bridge approaches should be straight for a minimum length of
25 m
30 m
50 m
15 m

⇒ A web plate is called unstiffened if the ratio of clear depth to thickness is less than.
35
50
60
85

⇒ Timber has more strength
Alone, the grains
Across the grains
Perpendicular to grains
In all directions

⇒ Maximum permissible slenderness ratio of compression members which carry dead and superimposed load, is.
350
250
180
80

⇒ For a cantilever beam of length L continuous at the support and unrestrained against torsion at the support and free at the end, the effective length l is equal to.
l = L
l = 2L
l = 0.5L
l = 3L

⇒ Normally, the angle of roof truss with asbestos sheets should not be less than
26'/2°
30°
35°
40°