Question is ⇒ For measuring temperatures below 800°C with high accuracy, the best instrument is, Options are ⇒ (A) optical pyrometer, (B) thermistor based thermometer, (C) GaAs junction diode thermometer, (D) platinum resistance thermometer, (E) , Leave your comments or Download question paper.

Question is ⇒ For measuring temperatures below 800°C with high accuracy, the best instrument is, Options are ⇒ (A) optical pyrometer, (B) thermistor based thermometer, (C) GaAs junction diode thermometer, (D) platinum resistance thermometer, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	For measuring temperatures below 800°C with high accuracy, the best instrument is
A.	optical pyrometer [Wrong Answer]
B.	thermistor based thermometer [Wrong Answer]
C.	GaAs junction diode thermometer [Wrong Answer]
D.	platinum resistance thermometer [Correct Answer]
View Answer 2 -1 Explanation:- Answer : D Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ When a 1 V increase in gate voltage changes the drain current 10 mA in an FET, its g_m equals
10 μμ
100 μμ
1000 μμ
10000 μμ

⇒ FM broadcast is done using
medium waves
short waves
VHF and UHF waves
microwaves

⇒ The Table given below is the mark obtained by 2 students in 8 different subjec
y + 0.57x = 9.7558
y - 0.57x = 9.758
033y + x = 6.335
0.33y - x = 6.335

⇒ Which of the following pulse communication system is inherently immune to noise?
PPM
PCM
PWM
PAM

⇒

Assertion (A): In design of circuit using BJT, a derating factor is used.

Reason (R): As the ambient temperature increases, heat dissipation becomes slower.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not a correct explanation of A
A is true but R is false
A is false but R is true

⇒ In the wave mechanical theory, the maximum of the charge distribution in the ground state occurs for a distance from the nucleus equal to
first Bohr radius
second Bohr radius
third Bohr radius
either first or second Bohr radius

⇒ As compared to tuned radio frequency receivers which of the following is the advantage of using superheterodyne receivers?
High gain and better sensitivity
Better selectivity at high frequencies
Stability
Noise suppression

⇒ In a positive-edge-triggered JK flip-flop, a low J and a low K produce __________ state. A high __________ on the rising edge of the clock.
inactive, reset
active, reset
active, toggle
inactive, toggle

⇒ Consider the following in C

An arithmetic operation between integer and an integer gives integer as the result.
An arithmetic operation between a real and a real constant gives real constant as the result.
An arithmetic operation between an integer constant and a real constant is not valid.

Which of the above are correct?
All
1 and 2 only
2 and 3 only
1 and 3 only

⇒ The arrangement in the given figure is a hybid T. If 100 mW fed at port 1, the power reflected back at port
0
25 mW
50 mW
100 mW

⇒ Two 2 port circuits are connected cascaded. To determine the response, it is more convenient to use
O.C. impedance parameters
S.C. admittance parameters
ABCD parameters
h parameters

⇒ Shannon's Law relates
antenna gain to frequency
noise power to bandwidth
information-carrying capacity to S/N ratio
transmission losses to noise

⇒ The pre-emphasis in FM aids in providing extra noise immunity by
emphasizing only the higher frequency components
emphasizing the entire frequency band
emphasizing only the lower frequency band
cutting down the low frequency noise

⇒ When temperature is above ferromagnetic Curie temperature, a ferromagnetic material
becomes a paramagnetic material
becomes a very strong ferromagnetic material
becomes diamagnetic material
none of the above

⇒ The most common method for biasing a JFET is
reverse bias
self bias
voltage divider bias
none of the above

⇒ The amplifier used in bootstrap voltage sweep should have a gain of
1
+∞
-1
-∞

⇒ For an RC impedance function
all poles lie on jω axis
all poles are simple ,
all poles are simple and lie on negative real axis
none of the above

⇒

Assertion (A): A GTO can be turned on and turned off by gate pulses

Reason (R): A GTO can be turned off by negative gate pulse.

Both A and R are correct and R is correct explanation of A
Both A and R correct but R is not correct explanation of A
A is correct but R is wrong
A is wrong but R is correct

⇒ The hexadecimal number 5 F is equal to binary number
1010011
1011001
1010101
1011111

⇒ In a dynamometer instrument, the moving coil is pressure coil.
TRUE
FALSE

⇒ In an RC series circuit R = 100 Ω and X_C = 10 Ω. In this circuit
the current and voltage are in phase
the current leads the voltage by about 6°
the current leads the voltage by about 84°
the current lags the voltage by about 6°

⇒ The resistance of voltmeter affects the accuracy of measurement in loss of charge method.
TRUE
FALSE

⇒ The maximum phase difference between the applied voltage and current in a RLC series current with finite values of R, L, C, and f can be
less than 90°
less than 45°
180°
30°

⇒

Assertion (A): The colour signal consists of only luminance signal

Reason (R): In India PAL colour signal system is used.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct but R is wrong
A is wrong but R is correct

⇒ F.T. of continuous non-periodic signal is
aperiodic
periodic
a and b
none

⇒ A clock signal driving a 6-bit ring counter has a frequency of 1 MHz. How long is each timing bit high?
1 ms
2 ms
3 ms
6 ms

⇒ A balun provides an impedance transformation of
0.667361111111111
0.334027777777778
0.167361111111111
0.0840277777777778

⇒ In the saturation region of CE output characteristics of n-p-n transistor, V_CE is about
0.5 V
15 V
- 0.5 V
- 15 V

⇒ If low pressure of 10^-6 mm of Hg is required to be measured, we should use
compound pressure gauge
thermocouple vacuum gauge
Pirani gauge
ionization type vacuum gauge

⇒ An A/D converter uses for reference purposes
DC voltage
a saw tooth generator
set of keys
a flip-flop