Question is ⇒ For maximum unclipped output from a CE amplifier, the Q point should be, Options are ⇒ (A) at the centre of dc load line, (B) at the centre of ac load line, (C) at the centre of collector current, (D) none of the above, (E) , Leave your comments or Download question paper.

Question is ⇒ For maximum unclipped output from a CE amplifier, the Q point should be, Options are ⇒ (A) at the centre of dc load line, (B) at the centre of ac load line, (C) at the centre of collector current, (D) none of the above, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	For maximum unclipped output from a CE amplifier, the Q point should be
A.	at the centre of dc load line [Wrong Answer]
B.	at the centre of ac load line [Correct Answer]
C.	at the centre of collector current [Wrong Answer]
D.	none of the above [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : B Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ A characteristic property of crystal is its periodicity of structure.
TRUE
FALSE

⇒ Which of the following statement is correct?
The input impedance of CE amplifier is usually around 10 Ω
The voltage gain of a transistor amplifier in CE mode is always less than unity
The output impedance of a transistor amplifier is independent of the transistor configuration
The voltage gain of a transistor amplifier is independent of the load resistance

⇒ Calculate the electrostatic force of repulsion between two mica particles at a distance of 10^-13 m from each other. Charge on a particle is 3.2 x 10^-19 C. (relative permittivity for mica is 5)
1.843 x 10^-15 N
9.2 x 10^-2 N
14.41 x 10^-9 N
none of these

⇒ A synchro transmitter receiver unit is a
two phase ac device
3 phase ac device
dc device
1 phase ac device

⇒ In two wattmeter method of 3 phase power measurement, when does one wattmeter read negative
when power factor is less than 0.5 lagging
when power factor is greater than 0.5 lagging
when power factor is less than 0.5
when power factor is unity

⇒ In 8085 microprocessor based system running at 3 MHz clock frequency what should be the minimum pulse width of the INTR signal, so that it is recognized successfully?
0.33 μs
0.666 μs
5.8 μs
none of these

⇒ Impedance inversion may be obtained with
a short circuited stub
a quarter wave line
an open circuited stub
a half wave line

⇒ The first and the last critical frequencies (singularities) of a driving point impedance function of a passive network having two kind of elements, are a pole and a zero respectively. The above property will be satisfied by
RL network only
RC network only
LC network only
RC as well as RL network

⇒ For a distortionless line, the parameters are related as
R/G = L/C
R/L = 1
R/G = C/L
RG = LC

⇒ In phase modulation, the phase deviation is
proportional to the amplitude of the signal and varies with frequency
remains constant while amplitude and frequency of signal varies
proportional to the amplitude of the signal and independent of the frequency
none of the above

⇒ A Ge diode operated at a junction temperature of 27°C. For a forward current of 10 mA, V_D is found to be 0.3 V. If V_D = 0.4 V then forward current will be
400 mA
475 mA
477 mA
480 mA

⇒ In position control system the device used for providing rate feedback voltage is
potentiometer
synchro-transmitter
synchro-transformer
tacho generator

⇒ Which of the following statement is correct?
Decimal 9 is represented as 1011 in Excess-3 code
Decimal 9 is represented as 1001 is BCD code
Decimal 10 is represented as 1100 is Gray code
Decimal 10 is represented as 1001 in binary code

⇒

Match the following:

	List I		List II
A.	On-off	1.	steam kettle with different settings
B.	Proportional	2.	Elevator
C.	Cascade	3.	Robot-positioning
D.	Digital	4.	Domestic Refrigerator

A-4, B-2, C-3, D-1
A-2, B-4, C-1, D-3
A-3, B-1, C-4, D-2
A-4, B-2, C-1, D-3

⇒ What is the characteristic of a good control system?
Sensitive to parameter variation
Insensitive to input command
Neither sensitive to parameter variation nor sensitive to input commands
Insensitive to parameter variation but sensitive to input commands

⇒ In a purely inductive ac circuit, the supply voltage and voltage induced across inductance are equal and opposite at all instants.
TRUE
FALSE

⇒ The density of the dynamic RAM is
more than that of static RAM
less than that of static RAM
equal to that to static RAM
equal to or more than that of static RAM

⇒ In 8421 Binary coded Decimal system the decimal number 237 is represented by
1000110111
1000111110
1000110111
10010010011

⇒ Armstrong F.M. transmitter performs frequency multiplication in stages
to increase the overall S/N
for convenience
to reduce the bandwidth
to find the desired value of carrier frequency with frequency deviation

⇒ In figure, I_D = 4 mA. Then V_{S20 V
16 V
6 V
0.6 V}

⇒ Which of these are universal gates?
Only NOR
Only NAND
Both NOR and NAND
NOR, NAND, OR

⇒ A crystal is frequently used in digital circuits for timing purpose because of its
low cost
high frequency stability
simple circuitry
ability to set frequency at desired value

⇒ The given figure shows a K-map for a Boolean function. The number of essential prime implicant
4
5
6
8

⇒ In a JFET
drain current is very nearly equal to source current
drain current is much less than source current
drain current may be equal to or less than source current
drain current may be even more than source current

⇒ The following circuit resonate
0.5 Hz
5 Hz
1 rad/sec
0.5 rad/sec

⇒ In 8085 which addressing mode is also called inherent addressing?
Direct
Register
Implicit
Immediate

⇒ A(A + B) =
A
A B
AB
AB

⇒ Dielectric constant and conductivity of rocky soil and flat sandy soil are around
10 and 20 mho/cm respectively
20 and 10 mho/cm respectively
2 and 5 mho/cm respectively
0.5 and 2 mho/cm respectively

⇒ Spontaneous polarization occurs in ferroelectric materials.
TRUE
FALSE

⇒ A computer program is used to read N and compute N !. IF N = 6, the result will be
6
12
720
1040