Question is ⇒ For low impedance SAW filter the most suitable material for substrate of SAW filter is, Options are ⇒ (A) PZT ceramics, (B) ZnO, (C) Lithium titanate, (D) Lithium neobate, (E) , Leave your comments or Download question paper.

Question is ⇒ For low impedance SAW filter the most suitable material for substrate of SAW filter is, Options are ⇒ (A) PZT ceramics, (B) ZnO, (C) Lithium titanate, (D) Lithium neobate, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	For low impedance SAW filter the most suitable material for substrate of SAW filter is
A.	PZT ceramics [Correct Answer]
B.	ZnO [Wrong Answer]
C.	Lithium titanate [Wrong Answer]
D.	Lithium neobate [Wrong Answer]
View Answer 2 -1 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ A system has poles at 0.01 Hz, 1 Hz and 80 Hz, zeros at 5 Hz, 100 Hz and 200 Hz. The approximate phase of the system response at 20 Hz is
-90°
0°
90°
-180°

⇒ Which of the following is not an internal DOS command?
VER
COPY
MEM
DATE

⇒

Assertion (A): ECL gate has very high speed of operation.

Reason (R): Transistors in ECL do not go into saturation region.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is true, R is false
A is false, R is true

⇒ In a transistor operating in forward active mode
depletion layer between emitter and base is thin and that between base and collector is also thin
both depletion regions are thick
depletion layer between emitter and base is thin and that between base and collector is thick
depletion layer between emitter and base is thick and that between base and collector is thin

⇒ The Nyquist plo
will start from (ω = ∞) in the first quadrant and will terminate (ω = 0) in the second quadrant
will start from (ω = ∞) in the fourth quadrant and will terminate (ω = 0) in the second quadrant
will start form (ω = ∞) in the second quadrant and will terminate (ω = 0) in the fourth quadrant
will start from (ω = ∞) in the first quadrant and will terminate (ω = 0) in the fourth quadrant

⇒ In broadside array
the principle direction radiation is perpendicular to the array axis and also to the plane containing the array elements
the principle direction radiation is parallel to the array axis and also to the plane containing the array elements
the principle direction radiation is parallel to the array axis and perpendicular to the plane containing the array elements
the principle direction radiation is perpendicular to the array axis and parallel to the plane containing the array elements

⇒ Which of the following is a valid real constant in FORTRAN 77?
1.2 E 231
3 E - 2
-3.2 E 2.3
1.2 E 23

⇒ An impulse function consist of
pure dc
pure a.c
entire frequency range with constant phase
infinite bandwidth with linear phase vaariations

⇒ The threshold voltage of an n-channel enhancement mode MOSFET is 0.5 when the device is biased at a gate voltage of 3V. Pinch off would occur at a drain voltage of
1.5 V
2.5 V
3.5 V
4.5 V

⇒ Find R_L for maximum power tran
3 Ω
1.125 Ω
4.17 Ω
none

⇒ A generator with an internal resistance of 600 Ω drives an amplifier whose input resistance is 400 Ω. The generator's open circuit voltages is 1 mV; the amplifier develops 100mV across an 8kΩ load. The voltage multiplication is
25
50
125
250

⇒

Assertion (A): Silicon is less sensitive to changes in temperature than germanium.

Reason (R): It is more difficult to produce minority carriers in silicon than in germanium.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not a correct explanation of A
A is true but R is false
A is false but R is true

⇒ Which one of the following blocks is not common in both AM and FM receivers?
RF amplifier
Mixer
IF amplifier
Slope detector

⇒ A vacant electronic state moves in the same direction as would a positive charge carrier.
TRUE
FALSE

⇒ The minterm designation for ABCD is
m₈
m₁₀
m₁₄
m₁₅

⇒ Spontaneous magnetisation is characteristic of ferromagnetic materials.
TRUE
FALSE

⇒ Bode magnitude plot is drawn between
magnitude of network function and ω
dB magnitude and log ω
dB magnitude and ω
log_e (magnitude) and log ω

⇒ The v-i characteristic shown in the given figure is
thermistor
photoconductor
varistor
none of the above

⇒ The damping ratio of a pair of complex poles when expressed in terms of angle θ measured from jω axis equal to
sin θ
cos θ
tan θ
cot θ

⇒ A ripple counter has 4 bits and uses flip flops with propagation delay time of 25 ns. The maximum possible time for change of state will be
25 ns
50 ns
75 ns
100 ns

⇒ A moving coil meter has 10 Ω resistance and requires 40 mA for full scale deflection. The shunt resistance required to convert it into 0-2 A ammeter is
0.1021 Ω
0.2041 Ω
0.256 Ω
0.4210 Ω

⇒ The correct sequence of parts in klystron amplifier are
anode, catcher cavity, cathode, buncher cavity
cathode, buncher cavity, catcher cavity, cavity
anode, buncher cavity, catcher cavity, cathode
cathode, catcher cavity, anode, buncher cavity

⇒ A specimen of a material has a resistivity of 1.78 x 10⁸ ohm-m. The material is
semiconductor
conductor
semiconductor or conductor
insulator

⇒ India's first domestic geostationary satellite 1NSAT-IA was launched on 10th April 1982 from
USSR
USA
UK
UP

⇒ The symbol ! in Java means
logical NOT
logical OR
AND
logical XOR

⇒ PID controlled system has
P and I actions in forward path and D action in feedback path
P and I actions in feedback path and actions in forward path
All the three (i.e., P, I and D) actions in forward path
All the three (i.e., P, I and D) actions in feedback path

⇒ A full adder is to be implemented using half adders and OR gates. A 4 bit parallel adder without any initial carry requires
8 half adders and 4 OR gates
8 half adders and 3 OR gates
7 half adders and 3 OR gates
7 half adders and 4 OR gates

⇒ The maximum range of a transmitter depends on
its frequency
its power
both its frequency and power
none of the above

⇒ For the K map of the given figure the simplified Boolean expressio
ACD + ABD + BCD
ACD + BCD
ACD + ABD
none of the above

⇒ An 8085 executes the following instructionsPC = 2715 H HL = 30A0 H
PC = 30A0H HL = 2715H
PC = 6104 H HL = 6140 H
PC = 6140H HL = 2715H