Question is ⇒ For H(s) to be positive real, the condition Re[H(jω)] ≥ 0 for 0 ≤ ω ≤ ∞ is, Options are ⇒ (A) a necessary condition, (B) a sufficient condition, (C) a necessary and sufficient condition, (D) is not a necessary condition, (E) , Leave your comments or Download question paper.

Question is ⇒ For H(s) to be positive real, the condition Re[H(jω)] ≥ 0 for 0 ≤ ω ≤ ∞ is, Options are ⇒ (A) a necessary condition, (B) a sufficient condition, (C) a necessary and sufficient condition, (D) is not a necessary condition, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	For H(s) to be positive real, the condition Re[H(jω)] ≥ 0 for 0 ≤ ω ≤ ∞ is
A.	a necessary condition [Correct Answer]
B.	a sufficient condition [Wrong Answer]
C.	a necessary and sufficient condition [Wrong Answer]
D.	is not a necessary condition [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Which of the following real expressions is incorrect in Pascal?
Y - X
(A + B) (C + D)
X / Y - Z
P * Z - 5.0

⇒ Alternating current can induce voltage because it has magnetic field which is
constant
time varying
stronger field than D.C.
closed loop nature.

⇒ The power density spectrum of noise voltage of resistor R can be expressed as
2 kTR
1 kTR
0.5 kTR
0.25 kTR

⇒ For a voltage transfer function H(s), realizable by RLC network, the following statements are made

H(s) cannot have a pole at s = 0
H(s) cannot have a pole at s = ± j4
H(s) cannot have a pole at s = ∞
H(s) cannot have a pole at s = + 2

Of these statements
3 and 4 are correct
2 and 4 are correct
1 and 2 are correct
1 and 3 are correct

⇒ An RL impedance function is to be synthesised in second Foster form. The proper function to be expanded is
Z(s)
sZ(s)
1/Z(s)
Z(s)/s

⇒ If word length is 16 bits the decimal equivalent of largest number which can be stored is
32767
32766
16383
16384

⇒ The purpose of using negative feedback in a op-amps is to
stabilize overall gain
increase output
stabilize overall gain and increase output
increase output and decrease input

⇒ In a clocked latch, clock drives
R NAND gate
S NAND gate
both R and S NAND gates
either R or S NAND gates

⇒ In figure, voltage across R₂ = + 10 V. If V_BE = 0.7 V and V_E = 0.7 V and R_E = 10 kΩ, current through R_{E1 mA
0.93 mA
2 mA
1.86 mA}

⇒ For a Mod-64 synchronous counter the number of flip flops and AND gates needed is
6 and 4 respectively
4 and 6 respectively
7 and 5 respectively
5 and 7 respectively

⇒ 2's complement of binary number 0101 is
1011
1111
1101
1110

⇒

Assertion (A): KCL is dual of KVL.

Reason (R): Node is dual of mesh.

Both A and R are true and R is correct explanation of A
Both A and R are true and R is not the correct explanation of A
A is true but R is false
A is false but R is true

⇒ In a material, the Fermi level is located between the centre of the forbidden band and the conduction band. Then what is that material?
A p-type semiconductor
An n-type semiconductor
An intrinsic semiconductor
An insulator

⇒ Consider the following statements about expressing real constants in exponential form in C

The mantissa and exponent are separated either by e or E.
The mantissa and exponent may have positive or negative sign.
Default sign of mantissa is positive.
Default sign of exponent is negative.

Which of the above statements are wrong?
1 only
1 and 4 only
1, 3 and 4 only
4 only

⇒ The resonance frequency of the circui
5.4 Kn₂
4.5 Kn₂
5 Kn₂
∞

⇒

Assertion (A): A two byte instruction of 8085 has an operation code in first byte and operand / address in the second byte.

Reason (R): If an instruction is too long it is possible to reduce its length by a number of methods.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct R is wrong
A is wrong R is correct

⇒

Assertion (A): BCD code is used in pocket calculators

Reason (R): BCD code is slower than binary.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is true, R is false
A is false, R is true

⇒ In 8085 microprocessor, an active low signal INTA is not needed from up service which of the following interrupt requ
TRAP
INTR
RST 7.5
RST 5.5

⇒ Which of these are allowed in Basic?
Arithmetic operators +, -, *, / etc.
Logical operators AND, OR, NOT
Relational operators =, <, > etc.
All of the above

⇒ Unit step is a
energy signal
power signal
neither energy nor power signal
none

⇒ ALU 1C 74181 can accept two words each having
2 bits
4 bits
8 bits
16 bits

⇒ A hertzian dipole has a radiation pattern with
a null in the direction of the dipole
a null in the plane perpendicular to the dipole
a peak in the direction of the dipole
none of the above

⇒ An RL impedance function can also be realized as
RC impedance function
RC admittance function
LC impedance function
LC admittance function

⇒

Assertion (A): A class C chopper can operate in first and second quadrants

Reason (R): A class B chopper operates only in second quadrant.

Both A and R are correct and R is correct explanation of A
Both A and R correct but R is not correct explanation of A
A is correct but R is wrong
A is wrong but R is correct

⇒ When a diode is forward biased, the diode current is
high
low
zero
low or zero

⇒ For a delayed half wave rectified wave, the average and rms values are lower than those for half wave.
TRUE
FALSE

⇒

Match the following:

	List I (Properties)		List II (Relations)
A.	Linear but NOT time-invariant	1.	y(t) = t²x(t)
B.	Time-invariant but NOT linear	2.	y(t) = t \|x(t)\|
C.	Linear and time invariant	3.	y(t) = \|x(t)\|
		4.	y(t) = x(t - 5)

A-1, B-3, C-4
A-2, B-3, C-4
A-3, B-1, C-2
A-1, B-2, C-3

⇒ Which one of the following power amplifier has the maximum efficiency?
Class A
Class B
Class AB
Class C

⇒ The property is not valid for basic singularity function is
it is even signal
convolution of any arbitary function x(t) and an impulse is the original function itself
the sum of two impulses at same location is the impulse with the strength equal to the summation of individual strengths.
none of these.

⇒ If the functions w, x, y, z are as foll
w = z x = z
w = z, x = y
w = y
w = y = z