Question is ⇒ For an RC driving point impedance function, the poles and zeros, Options are ⇒ (A) should alternate on real axis, (B) should alternate only on negative real axis, (C) should alternate on imaginary axis, (D) none of the above, (E) , Leave your comments or Download question paper.

Question is ⇒ For an RC driving point impedance function, the poles and zeros, Options are ⇒ (A) should alternate on real axis, (B) should alternate only on negative real axis, (C) should alternate on imaginary axis, (D) none of the above, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	For an RC driving point impedance function, the poles and zeros
A.	should alternate on real axis [Correct Answer]
B.	should alternate only on negative real axis [Wrong Answer]
C.	should alternate on imaginary axis [Wrong Answer]
D.	none of the above [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ A 4 bit modulo 16 ripple counter uses JK flip-flops. If the propagation delay of each FF is 50 ns. The max. clock frequency that can be used is equal to
20 MHz
10 MHz
5 MHz
4 MHz

⇒ Which of the following waves do not exist in waveguides?
TE waves
TM waves
TE and TM waves
TEM waves

⇒

Assertion (A): In control system velocity error is not an error in velocity but is an error in position due to a ramp input.

Reason (R): For a type of system velocity error is zero.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct but R is wrong
R is correct but A is wrong

⇒ The moving iron instruments are generally repulsion type.
TRUE
FALSE

⇒ A transistor has two p-n junctions. The batteries should be connected such that
both junctions are forward biased
both junctions are reverse biased
one junction is forward biased and the other is reverse biased
none of the above

⇒ A characteristic property of crystal is its periodicity of structure.
TRUE
FALSE

⇒ A shift register can be used for all of the following EXCEPT
ring counter
A/D conversion
series to parallel conversion
generation of delay

⇒ In a TWT the loss in attenuator is
almost equal to forward gain of tube
much less than forward gain of tube
much higher than forward gain of tube
almost infinite

⇒

Assertion (A): Inverse Laplace transform can be found from P(s) by inversion integral.

Reason (R): The function f(t) is assumed to be zero for t < 0.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct but R is wrong
R is correct but A is wrong

⇒ The skip distance is the maximum distance upto which ionospheric reflection is possible.
TRUE
FALSE

⇒ An engineer designs an amplifier to have a voltage gain of 60, but when constructed it only had a gain of 50. What value of feedback will double the gain?
0.005
0.0066
0.01
0.033

⇒ When an SCR is reverse biased
two junctions are reverse biased and one junction is forward biased.
all the three junctions are reverse biased.
one junction is reverse biased and two junctions are forward biased.
any of the above depending on the magnitude of reverse bias.

⇒ In the circuit of figure the current through 3 Ω resistance at t = &infin
0.166666666666667
2.5 A
3.1 A
0

⇒ In communication systems the frequency range used for voice is
15 Hz to 150 Hz
30 Hz to 1000 Hz
100 Hz to 1500 Hz
300 Hz to 3800 Hz

⇒ An increase of reverse voltage decreases the junction capacitance.
TRUE
FALSE

⇒ An ammeter of 0-25 A range has a guaranteed accuracy of 1% of full scale reading. The current measured is 5 A. The limiting error is
0.02
0.025
0.04
0.05

⇒ Microwaves
get reflected by ionosphere
are absorbed by ionosphere
are neither reflected nor absorbed by ionosphere
are both reflected and absorbed by ionosphere

⇒ For oscillations to starts, the loop gain A β of the oscillator must be initially
less than unity
0.5
1
more than unity

⇒ CW Doppler radar is capable of giving accurate measurements of relative velocities.
TRUE
FALSE

⇒ A lens has a hyperfocal distance of 7.5 m. It is focused at 7.5 m. Then
all objects from 7.5 m to infinity will appear in focus
all objects from 3.75 m to infinity will appear in focus
all objects from 0 to 7.5 m will appear in focus
all objects from 0 to 3.75 m will appear in focus

⇒ Which 8085 instruction causes exchange of contents of stack pointer with the contents of H L register pair?
XTHL
PCHL
LHLD
MVIA

⇒ In sinusoidal PWM for inverters the width of different pulses are not the same.
TRUE
FALSE

⇒

Assertion (A): In 8085, P flag is for parity checking.

Reason (R): If the result of ALU has even parity, P flag is set and if the result has odd parity, P flag is reset.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct R is wrong
A is wrong R is correct

⇒ An LED is
an ohmic device
a display device
a voltage regulated device
all of the above

⇒ Which one of following is a stataic system?
y(n) = x(n) - x(n - 1)
y(n) = x(2n) - x(2n-1)
y(n) = x(n - 1)
y(n) = e^x(n)

⇒ As per Euler's identity e^jωt = cos ωt + j sin ωt
TRUE
FALSE

⇒ A string constant in basic is
a string of capital alphabets A to Z, included in question mark
a string of capital alphabets A to Z and digits 0 to 9 included in question mark
a string of capital alphabets A to Z, digits 0 to 9 and special characters
a string of capital alphabets A to Z, digits 0 to 9 and special characters included in question mark

⇒ A 0.5 μF capacitor is connected across a 10 V battery. After a long time, the circuit current and voltage across capacitor will be
0.5 A and 0 V
0 A and 10 V
20 A and 5 V
0.05 A and 5 V

⇒ The following Variable Entered Map (VEM) represents which of the following funct
f(A, B, C, D) = ∑(1, 2, 3, 4, 7, 8, 9, 14, 15) + Φ(3, 5, 12, 13)
f(A, B, C, D) = ∑(1, 2, 4, 8, 10, 8, 13, 15) + Φ(3, 6, 12, 14)
f(A, B, C, D) = ∑(1, 2, 4, 7, 8, 10, 13, 15) + Φ(6, 12, 13)
f(A, B, C, D) = ∑(1, 2, 4, 7, 8, 9, 12, 13) + Φ(3, 5, 14, 15)

⇒ If the diameter of a wire is doubled, the current carrying capacity of the wire becomes
half
twice
four times
one-fourth