Question is ⇒ For an ideal transformer, Options are ⇒ (A) only Y parameter exist, (B) only Z parameter, (C) Z, Y both exist, (D) neither Z parameter nor Y parameter exist, (E) , Leave your comments or Download question paper.

Question is ⇒ For an ideal transformer, Options are ⇒ (A) only Y parameter exist, (B) only Z parameter, (C) Z, Y both exist, (D) neither Z parameter nor Y parameter exist, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	For an ideal transformer
A.	only Y parameter exist [Wrong Answer]
B.	only Z parameter [Correct Answer]
C.	Z, Y both exist [Wrong Answer]
D.	neither Z parameter nor Y parameter exist [Wrong Answer]
View Answer 4 -16 Explanation:- Answer : B Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The material which has zero temperature coefficient of resistance is
manganin
porcelain
carbon
aluminium

⇒ Which of the following is not a valid arithmetic statement in C?
x = x + 1
x = y ^* z
x ^* y = z
z = y / x

⇒ The units for apparent power are watts.
TRUE
FALSE

⇒

Assertion (A): Microprocessor 8085 can address 65536 memory locations.

Reason (R): Microprocessor 8085 has 16 address lines.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct R is wrong
A is wrong R is correct

⇒ In a 3 phase semiconverter, the freewheeling diode comes into operation only if firing angle
is zero
is 60°
is more than 60°
is more than 90°

⇒ MTI stands for
Moving Target Indicator
Microprocessor Tracking Index
Multiplexed Telemetry Index
Maximum Transmission Index

⇒ A rhombic antenna is a
resonant antenna
non-resonant antenna
coupled antenna
none of the above

⇒ A series RLC circuit has a resonant frequency of 1000 Hz. The maximum voltage across C is likely to occur at a frequency of about
1000 Hz
2000 Hz
1025 Hz
975 Hz

⇒ Conductivity is measured in terms of
mho/metre
ohm/metre
mho/metre²
ohm/metre²

⇒ In a digital counter the number of flip-flops is
always 2
always even
always odd
equal to the number of bits required in the final binary count

⇒ A CE amplifier has a high input signal. In the wave shape of emitter current
positive and negative half cycles will be symmetrical
positive half cycle will be elongated and negative half cycle will be compressed
positive half cycle will be compressed and negative half cycle will be elongated
the half cycles may be either elongated or compressed

⇒ An ac tachometer has a drag cup construction so that
rotor inertia is low
rotor body is conducting
rotor is easy to fabricate
both (a) and (b)

⇒ In root locus analysis the breakaway and break in points
lie on the real axis
either lie on the real axis or occur in complex conjugate pairs
always occur in complex conjugate pairs
none of the above

⇒ In the circuit shown in the given figure, power dissipated in the 5 Ω resisto
zero
80 W
125 W
405 W

⇒ In 3 phase power measurement by two wattmeter method, the reading of one wattmeter is zero. The power factor of load is
1
0.5
0
0.8

⇒ In DTL the junction transistor serves as
inverter
buffer amplifier
both (a) and (b)
none of the above

⇒ A series RLC circuit has a resonance frequency of 1 kHz and a quality factor Q = 100. If each of R, L and C is doubled from its original value, the new Q of the circuit is
25
50
100
200

⇒

Assertion (A): A slight change in pole-zero configuration can cause only minor changes in root locus configuration.

Reason (R): Asymptotes show the behaviour of root loci for |s| >> 1

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct but R is wrong
R is correct but A is wrong

⇒ An ideal op-amp has
infinite input and output resistance
low input and output resistance
low input and high output resistance
infinite input resistance and zero output resistance

⇒ In an ac network the sum of currents entering a node is 10 ∠45°. The sum of currents leaving the node is
19.32 ∠45°
15 ∠45°
20 ∠45°
zero

⇒ Which of the following is not necessarily the advantage of SSB over double sideband, full carrier AM?
The signal is more noise resistant
More channel space is available
Transmitter circuits must be more stable, given better reception
Considerably less power is required for the same signal strength

⇒

Assertion (A): C has 32 keywords like auto, if, do, float etc.

Reason (R): Key words can not be used as variable names in C.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct R is wrong
A is wrong R is correct

⇒

Match the following:

	List I		List II
A.	Ring modulator	1.	Clock recovery
B.	VCO	2.	Demodulation of FM
C.	Foster Seeley discriminator	3.	Frequency conversion
D.	Mixer	4.	Summing of two points
		5.	Generation of FM
		6.	Generation of DSB-SC

A-1, B-3, C-2, D-4
A-6, B-5, C-2, D-3
A-6, B-1, C-3, D-2
A-5, B-6, C-1, D-3

⇒ It is desired that transmission line and load should match for a range of frequencies. The best method is
to use a balun
to use a single stub of adjustable position
to use a double stub
to use a broad band amplifier

⇒ In a second order system, peak overshoot is independent of
damping factor
natural frequency
both damping factor and natural frequency
neither damping factor nor natural frequency

⇒ In a triode the potential of grid (with respect to cathode) is usually
zero
negative
positive
zero or positive

⇒ In microstrip line has dielectric material most commonly used is
silicon
rubber
plastic
bakelite

⇒ A 4 bit shift register is initialized to value 1000 for (Q₃, Q₂, Q₁, Q₀). The D input is derived from Q₀, Q₂ and Q₃ through two XOR gates as shown in figure. The pattern 1000 will appea
3rd pulse
7th pulse
6th pulse
4th pulse

⇒ In the absence of noise, if C is channel capacity in bits/s, δf is channel bandwidth in Hz and N is number of coding levels. Then
C = log₂ N
C = (δf) log₂ N
C = 2 (δf) log₂ N
C = 0.5 (δf) log₂ N

⇒ Consider a control system shown in given figure. For slight variation in G, the ratio of open loop sensitivity to closed loop sensitivity will be give
1 : (1 + GH)
1 : (1 + GH)^{- 1}
1 : (1 - GH)
1 : (1 - GH)^{- 1}