Question is ⇒ For an ideal 3000 Hz channel, Nyquist rate is, Options are ⇒ (A) 3000 bps, (B) 6000 bps, (C) 9000 bps, (D) 12000 bps, (E) , Leave your comments or Download question paper.

Question is ⇒ For an ideal 3000 Hz channel, Nyquist rate is, Options are ⇒ (A) 3000 bps, (B) 6000 bps, (C) 9000 bps, (D) 12000 bps, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	For an ideal 3000 Hz channel, Nyquist rate is
A.	3000 bps [Wrong Answer]
B.	6000 bps [Correct Answer]
C.	9000 bps [Wrong Answer]
D.	12000 bps [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : B Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The units of μ₀ and μ_r are
H/m for both
H/m for μ_r and no units for μ₀
H/m for μ₀ and no units for μ_r
Wb/m for μ₀ and no units for μ_r

⇒ The Voltage e₀ in the figu
2 V
4 V
4/3 V
8 V

⇒ In 8085 microprocessor, what is the length of temporary register?
6 bits
8 bits
12 bits
16 bits

⇒ Consider a random noise voltage which has a uniform density function as shown in the figure and is known to be wh
2 bits/reading
5 bits/reading
10 bits/reading
none of these

⇒ When measuring phase angle between two waves using a CRO, the time base generator is connected to
X plate
Y plate
both X and Y plate
neither X nor Y plates

⇒ In a colour TV receiver, AGC adjusts the gain of
RF stage only
IF stage only
RF stage and one or two IF stages
none of the above

⇒ The circuit in figur
positive clamper
negative clamper
positive peak clipper
negative peak clipper

⇒ In a J-K flip flop the input J = K = 1 pulse is about
set
reset
no change
toggle

⇒

Assertion (A): In circular waveguide the attenuation of TE₀₁ mode decreases as the operating frequency increases.

Reason (R): The wall currents in a circular waveguide in TE_Q1 mode are completely circumferential.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct but R is wrong
A is wrong but R is correct

⇒

Assertion (A): FET has characteristics very similar to that of pentode.

Reason (R): Both FET and pentode are voltage controlled devices.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not a correct explanation of A
A is true but R is false
A is false but R is true

⇒ The drain characteristics of JFET in operating region, are
inclined upwards
almost flat
inclined downwards
inclined upwards or downwards

⇒ The modulation of effective base width by collector voltage is known as Early effect, hence reverse collector voltage
increases both a and β
decrease both a and β
increase a but decrease β
decrease a but increase β

⇒ In the spectrum of a FM wave
the carrier frequency cannot disappear
the carrier frequency disappears when the modulation index is large
the amplitude of any sideband depends on the modulation index
the total number of sidebands depends on the modulation index

⇒ When phase-lag compensation is used in a system, then gain cross over frequency, bandwidth and undamped frequency are respectively
Increased, Increased, Increased
Increased, Increased, Decreased
Increased, Decreased, Decreased
Decreased, Decreased, Decreased

⇒ The function of interface circuit is
to match output conditions of driver with input conditions of load device
to match output conditions of load device with input conditions of driver
both (a) and (b)
neither (a) nor (b)

⇒ The phase angle of a lag circuit is
between 0 and -90°
between 0 and +90°
90°
more than 90°

⇒ Hay's bridge is suitable for inductances having low L/R ratio.
TRUE
FALSE

⇒ In a thermocouple temperature transducer, the output voltage is usually measured by
high resistance ammeter
high resistance voltmeter
high resistance milli-voltmeter
none of the above

⇒ In 8085 microprocessor system, what will be the total delay provided by the following loop.3.154 msec
3.514 msec
2.644 msec
3.166 msec

⇒ A parallel resonant circuit can be used
as a high impedance
to reject a small band of frequencies
both (a) and (b)
to amplify certain frequencies

⇒ Cells are connected in series to increase
current-rating
both voltage and current rating
the life of cell
voltage rating

⇒ A sinusoidal signal with peak to peak amplitude of 1.536 volt is quantized into 128 levels using a mid-rise uniform quantizer. The quantization noise power is
0.768 V
48 x 10^-6 V
12 x 10^-6 V
3.072 Volt

⇒ An antenna having an effective temperature of 27°K is fed into a microwave amplifier that has an effective noise temperature of 30 K. Calculate the available noise power per unit bandwidth
30 K
57 K
27 K
3K, K is Boltzmann constant

⇒ A current increasing at the rate of 1A/s is passed through a 1 H inductor. At t = 0, i = 0. The flux linkages after 1 sec are
0.5 Wb-turn
1 Wb-turn
2 Wb-turn
4 Wb-turn

⇒ Which of these has poor overload capacity?
PMMC instrument
Hot wire instrument
Dynamometer instrument
Both (a) and (c)

⇒ In an underdamped RLC series circuit, the natural frequency is ω_n. The frequency of damped oscillations is
ω_n
less than ω_n
more than ω_n
2 ω_n

⇒ The current in a circuit with 10 Ω resistance is i = 3 + 4 sin (100 t + 45°) + 4 sin (300 t + 60°) A. The rms current and power dissipated are
41 A and 410 W
35 A and 350 W
5 A and 250 W
11 A and 1210 W

⇒

Assertion (A): Silicon is less sensitive to changes in temperature than germanium.

Reason (R): Cut in voltage in silicon is less than that in germanium.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not correct explanation of A
A is true but R is false
A is false but R is true

⇒ In a positive edge triggered JK flip flop
High J and High K produce inactive state
Low J and High K produce inactive state
Low J and Low K produce inactive state
High J and Low K produce inactive state

⇒ On the basis of the type of chemical bonds, solids may be classified into
ionic crystals
ionic and valence crystals
ionic crystal, valence crystals and metals
ionic crystals, valence crystals, metal and vander wall crystals