Question is ⇒ For an amplifier the input output signals are shown in figure. The class of amplifie, Options are ⇒ (A) A, (B) AB, (C) B, (D) C, (E) , Leave your comments or Download question paper.

Question is ⇒ For an amplifier the input output signals are shown in figure. The class of amplifie, Options are ⇒ (A) A, (B) AB, (C) B, (D) C, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	For an amplifier the input output signals are shown in figure. The class of amplifie
A.	A [Wrong Answer]
B.	AB [Wrong Answer]
C.	B [Wrong Answer]
D.	C [Correct Answer]
View Answer 2 -1 Explanation:- Answer : D Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Consider the following statement associated with bipolar junction transistor and JFET

The former has higher input impedance than the later
The former has higher frequency stability than the later
The later has lower noise figure than the former
The later has higher power rating than the former.

Of these statements
1 and 2 are correct
2 and 3 are correct
3 and 4 are correct
1 and 4 are correct

⇒ In FSK no synchronous carrier is needed at the receiver
TRUE
FALSE
depend on distance
none

⇒ Calculate the critical frequency for the E layer if maximum ionic densities are 3 x 10⁶
15.58 x 10⁶
15.58 kHz
1.58 x 10³
None of the above

⇒ A silicon (PN) junction at a temperature of 20°C has a reverse saturation current of 10 pico Ampere. The reverse saturation current at 40°C for the same bias is approximately.
30 pA
40 pA
50 pA
60 pA

⇒ The carrier mobility in a semiconductor is 0.4 m²/Vs. Its diffusion constant at 300 K will be (in m²/s)
0.4
0.16
0.04
0.01

⇒ The main advantage of CMOS circuit is
high gain
high output impedance
low power consumption
high gain and high output impedance

⇒ The advantage of transistor over vacuum tube is
no heat is required
small size and light in weight
very low power consumption
all of the above

⇒ Which one of the following power amplifier has the maximum efficiency?
Class A
Class B
Class AB
Class C

⇒ In a 3 phase full wave regulator feeding a star connected resistance load the input voltage is 400 V line to line. The firing angle is 160°. The line to line output voltage would be
400 V
about 100 V
about 20 V
zero

⇒ An ideal op-amp has
infinite input and output resistance
low input and output resistance
low input and high output resistance
infinite input resistance and zero output resistance

⇒ In a series ac circuit a voltage of 20 V at 25 Hz causes a current of 0.20 A, while the same voltage at 75 Hz causes a current of 0.12 A. The circuit consists of
R and C in parallel
R and C in series
R and L in series
either (a) or (b)

⇒ The signal input to a given amplifier is made up of 100 mΩ signal power and 1 mΩ noise power. The amplifier contributes an additional 100 mΩ of noise and has a power gain of 20 dB. The input signal-to noise ratio is
2
10
20
100

⇒ An excitation is applied to a system at t = T, and its response is zero for -∞ < t < T, such a system is
non-causal system
Stable system
causal system
unstable system

⇒ MEWS stands for
Missile Early Warning System
Moving Target Early warning System
Missile Early Warning Signal
Moving Target Early Warning Signal

⇒ A transistor has a power rating of 8 W for a case temperature of 25°C. If derating factor is 30 mW/°C, the power rating for 55°C, case temperature is
8 W
7.5 W
7.1 W
6.8 W

⇒

Match the following:

	List I (type of controller)		List II (Operation)
A.	Pneumatic controller	1.	Flexible operation
B.	Hydraulic controller	2.	High torque high speed operation
C.	Electronic controller	3.	Fire and explosion proof operation

A-1, B-3, C-2
A-1, B-2, C-3
A-3, B-1, C-2
A-3, B-2, C-1

⇒ A single phase full wave regulator feeds a resistive load. The firing angle of thyristors is 90°. The input power factor is
1
0.707 lagging
0.5 lagging
0.2 lagging

⇒ A microprocessor uses 3 MHz oscillator. The duration of one T state is
1 μs
0.666 μs
0.333 μs
3 μs

⇒ A silicon PN junction diode under reverse bias has depletion region of width 10 μm. The relative permittivity of silicon, ε_r = 11.7 and the permittivity of free space ε₀ = 8.85 x 10^-12 F/m. The depletion capacitance of the diode per square meter is
100 μF
10 μF
1 μF
20 μF

⇒ Logic pulser
generates short duration pulses
generates long duration pulses
generates sinusoidal voltage
generates ideal pulses

⇒ If in a broadcasting studio, a 1000 kHz carrier is modulated by an audio signal of frequency range 100-5000 kHz, the width of channel is __________ kHz.
5
4.9
995
10

⇒ What is the period of the sinusoidal signal x(n) = 5 cos [0.2 pn]?
10
5
1
0

⇒

Assertion (A): The equation D = ∈₀∈_rE is applicable only to isotropic materials.

Reason (R): In polycrystalline materials, the directional effects are absent.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not correct explanation of A
A is true but R is false
A is false but R is true

⇒ In a conductor which of the following relations hold good?
∇ x D = r
∇ . D = r
∇ x D = 0
∇ . D = 0

⇒

Assertion (A): Hay's bridge in particularly suitable for measuring inductance having a comparatively low resistance.

Reason (R): In Hay's bridge the value of frequency supply must be known.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not correct explanation of A
A is true R is false
A is false R is true

⇒ For a = - 1, find the value of V_{2∞
0
V₁
none of the above}

⇒ One of the advantages of base modulation over collector modulation of a transistor class C amplifier is
improved efficiency
better linearity
high power output per transistor
the lower modulating power requirement

⇒ In a JK flip flop toggle means
set Q = 1 and Q = 0
set Q = 0 and Q = 1
change the output to the opposite state
no change in output

⇒ Find equivalent capacitance if each capacitance is
56 F
6/5 F
6/10 F
5/12 F

⇒ A current 10 sin (200t) A flows through a 5 mH inductance. The expression for voltage is
10 sin (200t + 90°)
10 sin (200t - 90°)
10 sin(1000t + 90°)
10 sin (1000t - 90°)