Question is ⇒ For a sine wave with peak value Imax the r.m.s. value is, Options are ⇒ (A) 0.5 Imax, (B) 0.707 Imax, (C) 0.9 Imax, (D) 1.414 Imax, (E) , Leave your comments or Download question paper.

Question is ⇒ For a sine wave with peak value Imax the r.m.s. value is, Options are ⇒ (A) 0.5 Imax, (B) 0.707 Imax, (C) 0.9 Imax, (D) 1.414 Imax, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	For a sine wave with peak value I_max the r.m.s. value is
A.	0.5 I_max [Wrong Answer]
B.	0.707 I_max [Correct Answer]
C.	0.9 I_max [Wrong Answer]
D.	1.414 I_max [Wrong Answer]
View Answer 14 -6 Explanation:- Answer : B Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Higher the Q of a series circuit
Broader its resonance curve
Narrower its pass band
Greater its band width
Sharper its resonace

⇒ In a series resonant circuit, the impedance of the circuit is
Maximum
Minimum
Zero
Infinite

⇒ A parallel resonant circuit can be used
As a high impedance
To reject a small band of frequencies
Both (A) and (B)
To amplify certain frequencies

⇒ The time period of a sine wave is 1/50 seconds. Its frequency is
20 Hz
30 Hz
40 Hz
50 Hz

⇒ The series element of a band stop filter is
Capacitive
Inductive
Parallel combination of L and C
Series combination of L and C

⇒ In a circuit containing R, L and C, power loss can take place
C only
L only
R only
All of the above

⇒ At half power points of a resonance curve, the current is____ times the maximum current.
1/2
1/ √2
√2
2

⇒ The r.m.s. value of a sine wave is 100A. Its peak value is
70.7 A
141.4A
150A
282.8 A

⇒ Which of the following is not a non-linear element ?
Transistor
Heater coil
Diode
Electric arc with unlike electrodes

⇒ The shunt element in a band pass filter is
Capacitive
Inductive
Parallel combination of L and C
Series combination of L and C

⇒ While drawing vector diagram for a series circuit the reference vector is
Voltage
Current
Power
Phase angle

⇒ In A.C. circuit laminated iron is invariably used in order to
Reduce eddy current loss
Increase heat radiation
Make assembly cheap and easier
Reduce circuit permeability

⇒ The peak value of a sine wave is 200 V. Its average value is
127.4V
141.4V
282.8V
200 V

⇒ Skin effect occurs when a conductor carries current at____ frequencies.
Very low
Low
Medium
High

⇒ A sine wave of voltage varies from zero to maximum of 200 V. How much is the voltage at the instant of 30° of the cycle ?
50V
82.8V
100V
173.2 V

⇒ In a series resonant circuit, the impedance of the circuit is
Minimum
Maximum
Zero
None of the above

⇒ Power factor of the following circuit will be unity
Inductance
Capacitance
Resistance
Both (A) and (B)

⇒ The power consumed in a circuit element will be least when the phase difference between the current and voltage
180°
90°
60°
0°

⇒ In a purely inductive circuit
Actual power is zero
Reactive power is zero
Apparent power is zero
None of these

⇒ The value of operator j2 is equal to
Zero
+1
-1
√-1

⇒ The best place to install a capacitor is
Very near to inductive load
Across the terminals of the inductive load
Far away from the inductive load
Any where

⇒ In A.C. circuit the power curve is a sine wave having
Double the frequency of voltage
Same frequency as that of voltage
Half the frequency of the voltage
None of these

⇒ Inductance affects the direct current flow
Only at the time of turning off
Only at the time of turning on
At the time of turning on and off
At all the time of operation

⇒ Power factor of the following circuit will be zero
Resistance
Inductance
Capacitance
Both (B) and (C)

⇒ The double energy transient occur in the
Purely inductive circuit
R-L circuit
R-C circuit
R-L-C circuit

⇒ In an A.C. circuit, a low value of kVAR compared with kW indicates
Low efficiency
High power factor
Unity power factor
Maximum Load current

⇒ How much r.m.s. current does a 300 W. 200V bulb take from the 200 V, 50 Hz power line ?
0.5A
1.5 A
2A
3A

⇒ Which of the following circuit component opposes the change in the circuit voltage
Inductance
Capacitance
Conductance
Resistance

⇒ The form factor is the ratio of
Peak value to r.m.s. value
r.m.s. value to average value
Average value to r.m.s. value
None of these

⇒ In an A.C. circuit power is dissipated in
Resistance only
Inductance only
Capacitance only
None of the above