Users Also Read

MCQ's Search Engine

Electrical Engineering

Mechanical Engineering

Civil Engineering

Automobile Engineering

Chemical Engineering

Computer Engineering

Electronics Engineering

Medical Science Engg

Q1. | For a sine wave with peak value E_{max}
the average value is |

A. | 0.636 E_{max} [Correct Answer] |

B. | 0.707 E_{max} [Wrong Answer] |

C. | 0.434 E_{max} [Wrong Answer] |

D. | 1.414 E_{max} [Wrong Answer] |

View Answer
Explanation:-
Answer : ADiscuss it below :RAKESH CHANDRA Said on 2016-07-27 09:36:48o.637 Emax !! OOPS Login [Click here] is required to post your answer/resultHelp other students, write article, leave your comments |

**Also Read Similar Questions Below :**

⇒ In a series resonant circuit, the impedance of the circuit is

Minimum

Maximum

Zero

None of the above

⇒ The power factor of incandescent bulb is

0.8 lagging

0.8 leading

Unity

Zero

⇒ The power is measured in terms of decibles in case of

Electronic equipment

Transformers

Current transformers

Auto-transformers

⇒ A sine wave of voltage varies from zero to maximum of 200 V. How much is the voltage at the instant of 30° of the cycle ?

50V

82.8V

100V

173.2 V

⇒ For the full wave rectified sine wave the r.m.s. value is

0.707 I

_{max}

0.636 I

_{max}

0.318 I

_{max}

Zero

⇒ Two waves of the same frequency have opposite phase when the phase angle between them is

360°

180°

90°

0°

⇒ The shunt element of prototype high pass filter is

Resistive

Inductive

Capacitive

Combination of L and C

⇒ Capacitive reactance is more when

Capacitances is less and frequency of supply is less

Capacitance is less and frequency of supply is more

Capacitance is more and frequency of supply is less

Capacitance is more and frequency of supply is more

⇒ The double energy transient occur in the

Purely inductive circuit

R-L circuit

R-C circuit

R-L-C circuit

⇒ At____ frequencies the parallel R-L circuit behaves as purely resistive.

Low

Very low

High

Very high

⇒ In an A.C. circuit I sin Φ is called

Active component

Wattless component

Any of the above

None of these

⇒ The series element of a band stop filter is

Capacitive

Inductive

Parallel combination of L and C

Series combination of L and C

⇒ Capacitors for power factor correction are rated in

kW

kVA

kV

kVAR

⇒ Which of the following is not a non-linear element ?

Transistor

Heater coil

Diode

Electric arc with unlike electrodes

⇒ The power factor at resonance in RLC parallel circuit is

Zero

0.08 Lagging

0.8 Leading

Unity

⇒ Poor power factor results in all of the following EXCEPT.

Overloading of transformers

Overloading of altemators

Reduction in power losses

Reduction in load handling capacity of electrical system

⇒ The ratio of active power to apparent power is known as ____ factor.

Demand

Load

Power

Form

⇒ The r.m.s. value of pure cosine function is

0.5 of peak value

0.707 of peak value

Same as peak value

Zero

⇒ In a parallel R-C circuit, the current always ____the applied voltage.

Lags

Leads

Remains in phase with

None of the above

⇒ Higher the Q of a series circuit

Broader its resonance curve

Narrower its pass band

Greater its band width

Sharper its resonace

⇒ Power factor of the following circuit will be unity

Inductance

Capacitance

Resistance

Both (A) and (B)

⇒ The power factor of a series R-L-C circuit at its half-power points is

Unity

Lagging

Leading

Lagging or leading

⇒ In an A.C. circuit, a low value of kVAR compared with kW indicates

Low efficiency

High power factor

Unity power factor

Maximum Load current

⇒ For a sine wave with peak value I

_{max}the r.m.s. value is

0.5 I

_{max}

0.707 I

_{max}

0.9 I

_{max}

1.414 I

_{max}

⇒ All the rules and laws of D.C. circuit also supply to A.C. circuit containing

Capacitance only

Inductance only

Resistance only

All above

⇒ For the same peak value which of the following wave will have the highest r.m.s. value ?

Square wave

Half wave rectified sine wave

Triangular wave

Sine wave

⇒ The transient currents are associated with the

Changes in the stored energy in the inductors and capacitors

Impedance of the current

Applied voltage to the circuit

Resistance of the circuit

⇒ Selectivities of different resonance circuits are compared in terms of their

Impedances

Reactances

Frequencies

Band widths

⇒ A parallel resonant circuit can be used

As a high impedance

To reject a small band of frequencies

Both (A) and (B)

To amplify certain frequencies

⇒ The best place to install a capacitor is

Very near to inductive load

Across the terminals of the inductive load

Far away from the inductive load

Any where