Question is ⇒ For a second order system, damping ratio ζ is such that 0 < ζ <. Then the roots of characteristic equation are, Options are ⇒ (A) real but not equal, (B) real and equal, (C) complex conjugate, (D) imaginary, (E) , Leave your comments or Download question paper.

Question is ⇒ For a second order system, damping ratio ζ is such that 0 < ζ <. Then the roots of characteristic equation are, Options are ⇒ (A) real but not equal, (B) real and equal, (C) complex conjugate, (D) imaginary, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	For a second order system, damping ratio ζ is such that 0 < ζ <. Then the roots of characteristic equation are
A.	real but not equal [Wrong Answer]
B.	real and equal [Wrong Answer]
C.	complex conjugate [Correct Answer]
D.	imaginary [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ In the circuit figure LED will be on when v_{1less than 6 V
more than 6 V
less than 12 V
more than 12 V}

⇒ In the figure, the
emits light when both S₁ and S₂ are closed
emits light when both S₁ and S₂ are open
emits light when only S₁ and S₂ is closed
does not Emit light, irrespective of the switched positions

⇒

Match the following:

	List I		List II
A.	Flash converter ADC	1.	requires conversion time of a few μs
B.	Dual slope ADC	2.	requires DAC
C.	Successive approximation ADC	3.	minimizes the effect of power supply interference
		4.	requires complex hardware
		5.	is a tracking ADC

A-2, B-3, C-4
A-4, B-3, C-2
A-5, B-4, C-3
A-1, B-2, C-5

⇒ It is desired to reduce distortion in an amplifier from 8% to 2% by using 5% negative feedback. The open and closed loop gains respectively are
60 and 15
15 and 60
6 and 1.5
1.5 and 6

⇒ Consider the following expressions in J
42, 40, 42 respectively
42, 42, 42 respectively
40, 42, 42 respectively
40, 40, 42 respectively

⇒ The current I_CBO flows in
base and emitter leads
base and collector leads
collector and emitter leads
collector, emitter and base leads

⇒ Which of these commutation methods uses an external pulse for commutation?
Class A
Class C
Class E
Class F

⇒ If a piece of wood is placed in a magnetic field
the magnetic field will not be affected
the magnetic lines of force will bend towards the piece
the magnetic lines of force will bend away from the piece
the flux may increase or decrease

⇒ The permanent magnet field system of brushless dc servo- motor is generally on
stator
rotor
partly on stator and partly on rotor
either (a) or (b)

⇒ A two winding transformer is feeding a single phase half wave rectifier circuit. The load is purely resistive. The rms value of transformer secondary current is I_s and rms value of load current in I_rms. Then
I_s = I_rms irrespective of the value of firing angle
I_s = 0.5 I_rms irrespective of the value of firing angle
I_s = I_rms if firing angle is less than 30°
I_s = I_rms if firing angle is more than 30°

⇒ A communication channel with AWGN operating at a signal to noise ratio SNR >> 1 and bandwidth B has capacity C₁. If the SNR is doubled keeping B constant, the resulting capacity C₂ is given by
C₂ ≈ 2C₁
C₂ ≈ C₁ + B
C₂ ≈ C₁ + 2B
C₂ ≈ C₁ + 0.3B

⇒ A system is stable if ROC
include the unit circle
exclude the unit circle
lies on Circle
entire plane

⇒ Two impedances 10 - j 10 and 10 + j 10 are connected in parallel. Their combined impedance is
5 + j5
5 - j5
10 + j0
20 - j10

⇒ In a semi converter feeding a resistive load, the firing angle is a. Each thyristor conducts for
p radians
(p - a) radians
(p + a) radians
(p - 0.5 a) radians

⇒ With increase in temperature, the electrical conductivity would
increase in metals as well as in intrinsic semiconductor
increase in metals but decrease in intrinsic semiconductor
decrease in metals but increase in intrinsic semiconductor
decrease in metals as well as in intrinsic semiconductor

⇒ In a display specified as 600 x 400 the number of pixels across the display screen is
600
400
240000
either (a) or (b)

⇒ The hexadecimal number 5 F is equal to binary number
1010011
1011001
1010101
1011111

⇒

Assertion (A): The surge current which an SCR can withstand is much higher than rms on state current.

Reason (R): The duration of surge current is very small.

Both A and R are correct and R is correct explanation of A
Both A and R correct but R is not correct explanation of A
A is correct but R is wrong
A is wrong but R is correct

⇒ A two branch parallel tuned circuit has a coil of resistance 100 Ω and inductance 0.005 H in one branch and 10 nF capacitor in the second branch. At resonance frequency is
100 rad/sec
10000 rad/sec
1000 rad/sec
more than 10000 rad/sec

⇒ The DTFT of x(n) = δ(n) will be
1
0
∞
not defined

⇒ In figure, the value of R shoul
0.2 Ω
0.1 Ω
0.05 Ω
0.1 Ω

⇒ In measuring a resistance by voltmeter-ammeter method, the voltmeter can be connected either across supply or across the resistance. If the resistance is low, the voltmeters should be connected
across the supply
across the resistance
either in two positions
preferably across the supply

⇒ A dc chopper V = 500 V feeds an electric fraction dc series motor. The chopping frequency is 400 Hz. The series inductance required to limit the maximum current swing to 10 A is
20 mH
about 31 mH
about 51 mH
about 92 mH

⇒ For the current wave i = 10 + 10 sin θ, the rms value is
0.416666666666667
12.247 A
20 A
14.14 A

⇒ Generally a VCR has
four stationary video heads
two stationary video heads
four rotating video heads
two rotating video heads

⇒ The MOS symbol shown indicates that

It is depletion type
It is enhancement type
It is channel
It is P-channel
Electrons flow from s to D
Holes flow from D to s

The true statements
1, 3, 6
1, 3, 5
2, 4, 6
2, 3, 5

⇒ An incremental model of a solid state device is one which represents the
ac property of the device at desired operating point
dc property of the device at all operating points
complete ac and dc behaviour at all operating points
ac property of the device at all operating points

⇒ When a current flows through a conductor,
an electric field exists at all points within the conductor
electric field exists only at all points on the surface of the conductor
electric field exists only at ends of the conductor
any of the above depending on magnitude of current

⇒ When performing numerical calculations in floating point arithmetic

Error may occur due to finite representation of numbers.
Error may occur due to rounding.
Error may occur due to finite representation of inherently infinite process.

Which of the above are correct?
All
1 and 2 only
1 and 3 only
2 and 3 only

⇒ The addressing mode depicted in the given figur
direct
register
register indirect
implicit