Question is ⇒ For a quadratic factor in transfer function the phase angle is not a function of damping factor., Options are ⇒ (A) TRUE, (B) FALSE, (C) , (D) , (E) , Leave your comments or Download question paper.

Question is ⇒ For a quadratic factor in transfer function the phase angle is not a function of damping factor., Options are ⇒ (A) TRUE, (B) FALSE, (C) , (D) , (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	For a quadratic factor in transfer function the phase angle is not a function of damping factor.
A.	TRUE [Wrong Answer]
B.	FALSE [Correct Answer]
View Answer 1 -1 Explanation:- Answer : B Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ To draw dc equivalent circuit for a CE amplifier circuit we should
Reduce all ac sources to zero
Open all capacitors
Reduce all ac sources to zero and open all capacitors
Reduce all ac sources to zero and short all capacitors

⇒ In a P-N-P junction transistor as compared to base region is more heavily doped so that
leakage current is minimized
recombination will be increased in the base region
the flow across the base regional is only because of electrons
the flow across the base region is mainly because of holes

⇒ One electron volt is equivalent to
1.6 x 10^-10 joule
1.6 x 10^-13 joule
1.6 x 10^-16 joule
1.6 x 10^-19 joule

⇒ If the current in a capacitor leads the voltage by 80°, the loss angle of capacitor is
80°
10°
100°
170°

⇒ The increase in intensity of trace in a CRO causes a change in
beam current
frequency of time base
gain of Y amplifier
accelerating voltage

⇒ Sulphur hexafluoride is used in
transformers
generators
relays
circuit breakers

⇒

Assertion (A): The polynomial s³ + 6s² + 12s + 8 is Hurwitz.

Reason (R): In a Hurwitz polynomial all coefficients are non-negative.

Both A and R are true and R is correct explanation of A
Both A and R are true and R is not the correct explanation of A
A is true but R is false
A is false but R is true

⇒ Which of the following pulse communication system is inherently immune to noise?
PPM
PCM
PWM
PAM

⇒ PROM is
Permanent Read Only Memory
Polarized Read Only Memory
Positive Read Only Memory
Programmable Read Only Memory

⇒ In 8085 microprocessor, what is the memory word size?
6 bits
8 bits
12 bits
16 bits

⇒ Which of the following instruments can be used for dc as well ac upto a few MHz?

Moving iron instrument
Thermocouple instrument
Induction instrument
Moving coil instrument

Select the correct answer as per following codes
2 only
2 and 3 only
1, 2 and 3 only
2 and 4 only

⇒ Which mode is usually preferred for cascading?
CE
CB
CC
Any of the above

⇒ In 8085 microprocessor, what is the length of SP (stack) pointer?
6 bits
8 bits
12 bits
16 bits

⇒ A sphere with charge Q was placed in, but not touching a larger hollow sphere. If there is any charge initially on the outer sphere; to remove it the outer sphere was earthed momentarily, and then the inner sphere was removed. The charge remaining on the outer sphere was then measured. This charge was found to be __________ to the charge on the inner sphere.
equal and of same again
equal and of opposite sign
unequal and of same sign
unequal and of opposite sign

⇒ The standard FORTRAN exponential form of decimal number 0.0000437 is
4.37 E - 5
4.37 E - 4
43.7 E - 5
43.7 E - 4

⇒ In the field controlled motor the entire damping comes from
armature resistance
back emf
motor friction and load
field resistance

⇒

Assertion (A): The condition of minimum distortion in a transmission line is L = RC/G.

Reason (R): Line loading means addition of inductance to satisfy the condition L = RC/G.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct but R is wrong
A is wrong but R is correct

⇒ The number of programmable 16 bit registers of 6800 are
2
3
4
5

⇒ The selectivity of a radio receiver is
its ability to reject adjacent unwanted signals
its ability to amplify weak signals
the frequency at which it gives maximum amplification to signal.
its ability to suppress noise.

⇒ In which frequency range is the noise figure in a transistor minimum
intermediate frequencies
low frequencies
high frequencies
very high frequencies

⇒ As per Shannon-Hartley theorem, a noise less Gaussian channel has
zero capacity
infinite capacity
small capacity
none of the above

⇒ The frequency response of a microphone means
bandwidth of frequencies having output with in ± 1 dB of the output at 1000 Hz
bandwidth of frequencies having output with in ± 3 dB of the output at 1000 Hz
bandwidth of frequencies having output with in ± 1 dB of the output at 500 Hz
bandwidth of frequencies having output with in ± 3 dB of the output at 500 Hz

⇒ A 1 MHz sinusoidal carrier is amplitude modulated by a symmetrical square wave of period 100 μ sec. Which of the following frequencies will not be in the modulated signal?
990 kHz
1010 kHz
1020 kHz
1030 kHz

⇒ Which of these has highly doped p and n region?
PIN diode
Tunnel diode
Schottky diode
Photodiode

⇒

Assertion (A): The transient performance of a control system is generally analysed by using unit step function as reference input.

Reason (R): Impulse is the most common input found in practice.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct but R is wrong
R is correct but A is wrong

⇒ A semiconductor Read-only-Memory basically is
a combinational logic circuit
a set of flip-flop memory elements
a sequential circuit with flip-flops and gates
none of the above

⇒ For satellite communication, standard Earth stations have antenna diameters in the range of __________ metre.
27.5 to 30
10 to 15
30 to 50
5 to 10

⇒ A buffer is a device that isolates other devices. Typically a buffer has
a high input impedance and a low output impedance
a high input impedance as well as output impedance
a low input impedance and a high output impedance
a low input impedance as well as output impedance

⇒ The proper exponential form of - 0.0032 in FORTRAN 77 is
-3.2 E - 3
-0.0032
-0.00032 EI
-0.032 E - 1

⇒ In figure, the switch is closed at t = 0. At t = 0⁺ The value of current supplied by batter
0.0416666666666667
0.0833333333333333
zero
infinity