Question is ⇒ For a NAND SR latch of input is the normal resting state of inputs is, Options are ⇒ (A) S = R = 1, (B) S = 0, R = 1, (C) S = 1, R = 0, (D) S = R = 0, (E) , Leave your comments or Download question paper.

Question is ⇒ For a NAND SR latch of input is the normal resting state of inputs is, Options are ⇒ (A) S = R = 1, (B) S = 0, R = 1, (C) S = 1, R = 0, (D) S = R = 0, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	For a NAND SR latch of input is the normal resting state of inputs is
A.	S = R = 1 [Correct Answer]
B.	S = 0, R = 1 [Wrong Answer]
C.	S = 1, R = 0 [Wrong Answer]
D.	S = R = 0 [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ SSI is used in flip flops.
TRUE
FALSE

⇒ Gain stability in an oscillator can bs achieved by
providing negative feedback
providing positive feedback
using low Q circuits
controlling the gain

⇒ A current of 3.18 A is flowing through resistance of 35.68 Ω. The voltage drop across resistance to the appropriate number of significant figures is
113.4624 V
113.462 V
113.46 V
113 V

⇒ In 8085 microprocessor based system running at 3 MHz clock frequency what should be the minimum pulse width of the INTR signal, so that it is recognized successfully?
0.33 μs
0.666 μs
5.8 μs
none of these

⇒ In Pulse Code Modulation system
large bandwidth is required
quantising noise can be overcome by companding
quantising noise can be reduced by decreasing the number of standard levels
suffers from the disadvantage of its incompatibly with TDM

⇒ A TV receiver has 20 kV EHT supply and total beam current (for 3 electron guns) of 1500 μA. The power handled by IHVT is
3 W
30 W
300 W
0.3 W

⇒ Two phasors having rms values V₁ and V₂ which are added to give a phasor having rms value V₃. V₃ is maximum if phase angle between V₁ and V₂ is
90°
180°
270°
360°

⇒ The total number of fundamental products of three variables is
3
5
8
16

⇒ The typical squelch circuit
cuts off an IF amplifier when the AGC is maximum
cuts off an IF amplifier when the AGC is minimum
cuts off an audio amplifier when the carrier is absent
eliminates the RF interference when the signal is weak

⇒ A transponder is a satellite equipment which
receives a signal from Earth station and amplifies
changes the frequency of the received signal
retransmits the received signal
does all of the above-mentioned functions

⇒ In a circuit containing a complex impedance, maximum power transfer takes place when load is
pure resistance
equal to the complex impedance
conjugate complex of the circuit impedance
none of the above

⇒ The normal operation of JFET is
constant voltage region
constant current region
both constant voltage and constant current regions
either constant voltage or constant current region

⇒ The number of bits in a nibble is
8
4
2
16

⇒ In order to achieve accuracy, the slide wire of a potentiometer should be
as long as possible
as short as possible
neither too long nor too short
very thin

⇒ A horizontal output stage is cutoff for retrace and 40% of trace. If time for each horizontal line is 64 μs and retrace time is 12 μs, the transistor is conducting for about
64 μs
6.4 μs
31 μs
3.1 μs

⇒ Which of the following is not an omnidirectional antenna?
Log periodic
Half-wave dipole
Discone
Marconi

⇒ An S/N ratio of 3 expressed in db is
4.8 dB
2.4 dB
0.48 dB
0.24 dB

⇒ Some ADCs are

Parallel
Updown
Single slope
Dual slope
Successive approximation
Stair step

Out of above which ones do not use DAC?
1 only
1, 3, 4
1, 2, 3
1, 5, 6

⇒ The modulation index of an AM wave is measured using a CRO. The waveform is as shown in figure, the modulation index is nea
0.43
0.3
0.23
0.17

⇒ In pulse code modulation when the maximum frequency in the signal is f_max the bandwidth required will be
≤ p.f_max
≥ p.f_max
≤ (p.f_max)²
≥ (p.f_max)²

⇒

Assertion (A): Synchronous counter has higher speed of operation than ripple counter

Reason (R): Synchronous counter uses high speed flip flops.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is true, R is false
A is false, R is true

⇒ Bridge circuits using RTD in temperature measurement usually employ 3 lead system so as to obtain
higher sensitivity
better impedance matching
compensation for signal wire resistance
reduction in power consumption

⇒ In a zener diode
forward voltage rating is high
negative resistance characteristics exists
sharp breakdown occurs at low reverse voltage
none of the above

⇒ A long specimen of P type semiconductor material
is + vely charged
is electrically neutral
has an electric field directed along its length
acts as a dipole

⇒ A tweeter should be fed from the input through a
low pass filter
high pass filter
band pass filter
band stop filter

⇒ Zip floppy has a capacity of
50 MB
500 MB
25 MB
100 MB or 250 MB

⇒ Consider the differential amplifier shown in figure. (Assume β is very hi
5 V
10 V
15 V
30 V

⇒ The scale of moving iron instrument is linear.
TRUE
FALSE

⇒ The PAM Signal can be detected by
Band pass filter
Band stop filter
High pass filter
Low pass filter

⇒ Which of the following computer memories is fastest?
Cache
Primary
Mass storage
Off line back up