Users Also Read

MCQ's Search Engine

Electrical Engineering

Mechanical Engineering

Civil Engineering

Automobile Engineering

Chemical Engineering

Computer Engineering

Electronics Engineering

Medical Science Engg

Q1. | For 200 V r.m.s. value triangular wave, the peak voltage will be |

A. | 200 V [Wrong Answer] |

B. | 222 V [Wrong Answer] |

C. | 282 V [Wrong Answer] |

D. | 346 V [Correct Answer] |

View Answer
Explanation:-
Answer : DDiscuss it below :Jaydeep Said on 2017-05-09 18:50:57
!! OOPS Login [Click here] is required to post your answer/resultHelp other students, write article, leave your comments |

**Also Read Similar Questions Below :**

⇒ The shunt element in a band pass filter is

Capacitive

Inductive

Parallel combination of L and C

Series combination of L and C

⇒ The power taken by a 3-Φ load is given by the expression

√3 V

_{L}I

_{L}sinΦ

√3 V

_{L}I

_{L}cosΦ

3 V

_{L}I

_{L}sinΦ

3 V

_{L}I

_{L}cosΦ

⇒ When an alternating current passes through an ohmic resistance the electrical power converted into heat is

Apparent power

True power

Reactive power

None of the above

⇒ The shunt element of prototype high pass filter is

Resistive

Inductive

Capacitive

Combination of L and C

⇒ For the same peak value, which of the following wave has the least mean value ?

Half wave rectified sine wave

Triangular wave

Sine wave

Square wave

⇒ A network is said to be non-linear if it does not satisfy

Homogeneity condition

Superposition condition

Both (A) and (B)

Associative condition

⇒ The product of apparent power and cosine of the phase angle between circuit voltage and current is

True power

Reactive power

Volt-amperes

Instantaneous power

⇒ In a pure resistive circuit

Current lags behind the voltage by 90°

Current leads the voltage by 90°

Current can lead or lag the voltage by 90°

Current is in phase with the voltage

⇒ A sine wave of voltage varies from zero to maximum of 200 V. How much is the voltage at the instant of 30° of the cycle ?

50V

82.8V

100V

173.2 V

⇒ In a circuit containing R, L and C, power loss can take place

C only

L only

R only

All of the above

⇒ In a parallel R-C circuit, the current always ____the applied voltage.

Lags

Leads

Remains in phase with

None of the above

⇒ In A.C. circuit the power curve is a sine wave having

Double the frequency of voltage

Same frequency as that of voltage

Half the frequency of the voltage

None of these

⇒ The r.m.s. value of a half-wave rectified current is 100 A. Its value for full-wave rectification would be____ amperes.

141.4

200

200/π

40/π

⇒ The power factor of incandescent bulb is

0.8 lagging

0.8 leading

Unity

Zero

⇒ A resonance curve for a series circuit is a plot of frequency versus

Current

Voltage

Impedance

Reactance

⇒ The safest value of current the human body can carry for more than 3 second is

4 mA

9 mA

15 mA

25 mA

⇒ The r.m.s. value and mean value is the same in the case of

Triangular wave

Sine wave

Square wave

Half wave rectified sine wave

⇒ The time constant of a series R-C circuit is given by

R/C

RC

^{2}

RC

R

^{2}C

⇒ Skin effect occurs when a conductor carries current at____ frequencies.

Very low

Low

Medium

High

⇒ For a sine wave with peak value E

_{max}the average value is

0.636 E

_{max}

0.707 E

_{max}

0.434 E

_{max}

1.414 E

_{max}

⇒ The best place to install a capacitor is

Very near to inductive load

Across the terminals of the inductive load

Far away from the inductive load

Any where

⇒ For the full wave rectified sine wave the r.m.s. value is

0.707 I

_{max}

0.636 I

_{max}

0.318 I

_{max}

Zero

⇒ In a purely inductive circuit

Actual power is zero

Reactive power is zero

Apparent power is zero

None of these

⇒ For 200 V r.m.s. value triangular wave, the peak voltage will be

200 V

222 V

282 V

346 V

⇒ The voltage of domestic supply is 220 V. This figure represents-

Mean value

r.m.s. value

Peak value

Average value

⇒ The negative maximum of a cosine wave occurs at

30

45

90

180

⇒ The ratio of the bandwidth to the resonance frequency is called the____ of the circuit.

Impedance

Susceptance

Quality factor

Selectivity

⇒ The power consumed in a circuit element will be least when the phase difference between the current and voltage

180°

90°

60°

0°

⇒ In the R - L - C containing R = 4.5ω L = 0.06 H,C = 0.6 µF the power factor will be

Zero

Lagging

Leading

Unity

⇒ The power factor at resonance in RLC parallel circuit is

Zero

0.08 Lagging

0.8 Leading

Unity