Question is ⇒ Fields are said to be circularly polarised if their magnitudes are, Options are ⇒ (A) equal and they are in phase, (B) equal but they differ in phase by ± 90°, (C) unequal and differ in phase by ± 90°, (D) unequal but are in phase, (E) , Leave your comments or Download question paper.

Question is ⇒ Fields are said to be circularly polarised if their magnitudes are, Options are ⇒ (A) equal and they are in phase, (B) equal but they differ in phase by ± 90°, (C) unequal and differ in phase by ± 90°, (D) unequal but are in phase, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Fields are said to be circularly polarised if their magnitudes are
A.	equal and they are in phase [Wrong Answer]
B.	equal but they differ in phase by ± 90° [Correct Answer]
C.	unequal and differ in phase by ± 90° [Wrong Answer]
D.	unequal but are in phase [Wrong Answer]
View Answer 2 -1 Explanation:- Answer : B Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ In the saturation region of CE output characteristics of n-p-n transistor, V_CE is about
0.5 V
15 V
- 0.5 V
- 15 V

⇒ For the circuit shown in the figure, what is the frequency of the outpu
Twice the input clock frequency
Half the input clock frequency
Same as input clock frequency
Inverse of the propagation delay of the FF

⇒ Which of the following statement regarding waveguides is incorrect?
At waveguide can be coupled to a coaxial cable
At frequencies below the cut off value the wave progresses across the waveguide after total reflections
Waveguides are usually air filled hollow conducting metallic tubes for transmitting UHF and microwaves
Waveguides can handle large power at UHF and microwaves

⇒ Which of the following is a valid integer variable in Fortran 77?
KM
K M - 1
DELHI
318

⇒ In a hot wire instrument, the deflection is proportional to
peak value of ac current
average value of ac current
rms value of ac current
either (a) or (b)

⇒ The number of valence electrons in a silicon atom is
4
2
1
0

⇒ The value of VSWR is taken as ∞ when the line is
short-circuited
open-circuited
terminated with full load
terminated with load equal to the characteristic impedance of the load

⇒ Which of the following is a circularly polarized antenna?
Horn
Dipole
Helical
Pyramidal

⇒ The phase difference (jω - p₁) means
phasor drawn from p₁ to jω
phasor drawn from origin to p₁
phasor directed from origin to jω point
phasor directed from jω to p₁

⇒ Schmitt trigger can be used as a
comparator
square-wave generator
flip-flop
all of these

⇒ Both X and Y plates of a CRO are excited by ac signals. The display is an ellipse which makes one rotation in 5 seconds. This means that
the frequency of one input is 5 times that of other
the difference between the frequencies of the two signals is one fifth of hertz
the difference between the frequencies of the two signals is 5 Hz
either (a) or (c)

⇒ The basic storage element in a digital system is
flip flop
counter
multiplexer
encoder

⇒ In figure the dc emitter current of each transistor is a
4 mA
2 mA
3 mA
1 mA

⇒

Assertion (A): The main use of Miller integrator is to generate ramp

Reason (R): An inverting amplifier can handle more than one input at the same time.

Both A and R are correct and R is correct explanation for A
Both A and R are correct but R is not correct explanation for A
A is correct R is wrong
A is wrong R is correct

⇒ In an impedance smith chart, a clockwise movement along a constant resistance circle gives rise to
decrease in the value of reactance
an increase in the value of reactance
no change in the reactance value
no change in the impedance value

⇒ A separately excited dc motor is run from a dc source through a chopper. At 600 rpm and rated torque, the duty cycle of chopper is 0.8. At 600 rpm and half the rated torque, the duty cycle is likely to be
0.9
0.8
0.75
0.6

⇒ Which of the following is used to generate PDM?
Free running multi-vibrator
Monostable multi-vibrator
JK flip-flop
Schmitt trigger

⇒ The inductance of a coil can be increased by
choosing core material having high relative permeability
decreasing diameter of the former
decreasing the number of turns
increasing core length

⇒ In the case of the circuit shown in the figure V_io = 10 mV dc maximum, the maximum possible output offset voltage V_oo caused by the input offset voltage V_io with respect to groun
60 mV dc
110 mV dc
130 mV dc
150 mV dc

⇒ Which one most appropriate dynamic system?
y(n) + y(n - 1) + y(n + 1)
y(n) + y(n - 1)
y(n) = x(n)
y(n) + y(n - 1) + y(n + 3) = 0

⇒ In figure, Z_a = 100∠50°, Z_b = 300∠-90° and Z_c = 200∠0°. For balanced condition, Z_d will
600∠ - 40°
600∠140°
600∠ - 140°
150∠140°

⇒ The adjustment of position of shading bands, in an energy meter, is done to provide
friction compensation
creep compensation
braking torque
none of the above

⇒ Personal computer cannot be used for which one of the following?
Game playing
Weather forecasting
Office Automation
Home computing

⇒ The changes in ambient temperature affect the open loop gain of amplifier.
TRUE
FALSE

⇒ Consider the following program in Ba
60, 20, 20, 30, 10
10, 30, 20, 20, 60
60, 20, 30, 10, 20
60, 30, 10, 20, 20

⇒ The torque in induction wattmeters due to
capacitive current
electrostatic effect
hall effect
eddy currents

⇒ Which of the following statement is false?
The zener diode is uses as a constant voltage source
The SCR is a silicon rectifier with a gate electrode to control when current flows from cathode to anode
The gate electrode in the FET corresponds to the collector in a bipolar transistor
None of the above

⇒ In using KCL it is necessary that current leaving a node is written as negative.
TRUE
FALSE

⇒ Which of the following is/are not a property/properties power spectral density function Sx(ω)?
Sx(ω) is real function of ω
Sx(ω) is a even function of ω
Sx(ω) is non-positive function of ωSx(ω) ≤ 0 for all ω
All of the above

⇒ For BJT transistor. The maximum power dissipation is specified as 350 mW if ambient temperature is 25°C. If ambient temperature is 60°C the maximum power dissipation should be limited to about
100 mW
250 mW
450 mW
600 mW