Question is ⇒ Epitaxial growth is used in ICs, Options are ⇒ (A) because it produces low parasitic capacitance, (B) because it yields back to back isolating pn Junction, (C) to grow single crystal n doped silicon on a single crystal P-type substrate, (D) to grow Selectivity single crystal P doped silicon of one resistivity on a P type substrate of a different resistivity, (E) , Leave your comments or Download question paper.

Question is ⇒ Epitaxial growth is used in ICs, Options are ⇒ (A) because it produces low parasitic capacitance, (B) because it yields back to back isolating pn Junction, (C) to grow single crystal n doped silicon on a single crystal P-type substrate, (D) to grow Selectivity single crystal P doped silicon of one resistivity on a P type substrate of a different resistivity, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Epitaxial growth is used in IC_s
A.	because it produces low parasitic capacitance [Wrong Answer]
B.	because it yields back to back isolating pn Junction [Wrong Answer]
C.	to grow single crystal n doped silicon on a single crystal P-type substrate [Wrong Answer]
D.	to grow Selectivity single crystal P doped silicon of one resistivity on a P type substrate of a different resistivity [Correct Answer]
View Answer 1 -1 Explanation:- Answer : D Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ A Hartley oscillator is used for
very low frequencies
radio frequencies
micro wave frequencies
audio frequency

⇒ A feedback network to be used with an amplifier to provide oscillation is tested and found to give an output of 0.124 V with a 0.5 V input. What will be the effect on output if the amplifier's gain is twice that required by the Barkhausen criterion?
Linear oscillations
Non-linear oscillations
Damped oscillations
No oscillations

⇒ The polar plot of a transfer function passes through (-1, 0) point. The gain margin is
zero
- 1 dB
1 dB
infinity

⇒ Saturation region of a JFET is also known as
source region
analog region
pinch off region
ohmic region

⇒ Kirchoff's laws are applicable to
steady state conditions only
transient conditions only
both steady state and transient condition
both steady state and transient condition but with some constraints

⇒ The ratio of active power to apparent power is known as __________ factor.
power
load
form
demand

⇒ Which of the following is not a characteristic of a flip flop?
It is a bistable device
It has two outputs
It has two outputs are complement of each other
It has one input terminal

⇒ The realization of the term Ks yields
a resistance of value K ohms
a capacitances of value K farads
an inductance of value k farads
either (b) or (c)

⇒ To separate channels in FDM receiver we have to use
integration
AND gate
band pass filter
differentiation

⇒ The expression Y (A, B, C) = ∑m (1, 3, 5, 6) is to realized using a multiplexer. Then
use 8 : 1 multiplexer and ground input lines 1, 3, 5, 6
use 8 : 1 multiplexer and ground input lines 0, 2, 4, 7
use 8 : 1 multiplexer and ground input lines 0, 1, 2, 3
use 8 : 1 multiplexer and ground input lines 4, 5, 6, 7

⇒ In JK flip flop toggle state exists if
J = 0, K = 1
J = 1, K = 0
J = 0, K = 0
J = 1, K = 1

⇒ The effective value of the waveform in the given figur
5
2.5
2.5
5.0

⇒ Consider an angle modulated si
10W
18W
20W
28W

⇒ Zero bias works only with
D MOSFETs
E MOSFETs
both D and E MOSFETs
neither D nor E MOSFETs

⇒ The number of flip flops required to construct a register to store number 102₁₀ in binary form is
2
4
8
10

⇒

Match the following:

	List I (BHE, A0)		List II (Word is read/write)
A.	0, 0	1.	1 byte from/to odd address
B.	0, 1	2.	1 byte from/to even address
C.	1, 0	3.	16 bit word
D.	1, 1	4.	None

A-1, B-2, C-3, D-4
A-3, B-1, C-2, D-4
A-2, B-3, C-4, D-1
A-4, B-1, C-2, D-3

⇒ Full adder circuit can be implemented by
Multiplexers
Half adders
AND or OR gates
Decoders

⇒

Assertion (A): CMOS devices have very low power consumption

Reason (R): CMOS devices have high noise margin.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is true, R is false
A is false, R is true

⇒ Digital circuits mostly use
Diodes
Bipolar transistors
Diodes and bipolar transistors
Bipolar transistors and FETs

⇒ An 8 bit DAC has a full scale output of 2 mA and full scale error of ± 0.5%. If input is 10000000 the range of outputs is
994 to 1014 μA
990 to 1020 μA
800 to 1200 μA
none of the above

⇒ The conductivity of a semiconductor crystal due to any current carrier is not proportional to
mobility of the carrier
effective density of states in the conduction band
electronic charge
surface states in the semiconductor

⇒ The dielectrics having only one kind of atoms are known as elemental dielectrics.
TRUE
FALSE

⇒ Binary 1111 when subtracted from binary 11111 is
101110
10110
10000
100010

⇒ A moving coil instrument has a resistance of 0.5 Ω and a full scale deflection of 0.1 A. To convert it into an ammeter of 0-10 A the shunt resistance should be
0.004 Ω
0.005 Ω
0.05 Ω
0.1 Ω

⇒ Which of the following lines is non-radiating?
Open two wire
Coaxial
Both
None of the above

⇒ The current wave of figure, is passed through a 3 H inductor during the period 0 to 2 sec
is 3 V
is 6 V
increases from 0 at t = 0 to 6 V at t = 2 seconds
increases from 0 at t = 0 to 6 V at t = 2 seconds and then decreases

⇒ What is the correct sequence of the following step in the fabrication of a monolithic, Bipolar junction transistor?

Emitter diffusion
Base diffusion
Buried layer formation
E pi-layer formation

Select the correct answer using the codes given below:
3, 4, 1, 2
4, 3, 1, 2
3, 4, 2, 1
4, 3, 2, 1

⇒ The type of noise that interfere very much with high frequency transmission is
white
transit time
flicker
shot

⇒ In filter system of sideband suppression the advantage of using mechanical filter is
smaller size
good bandpass
good attenuation characteristics
all of the above

⇒ The following sequence represents autocorrelation of a real valued signal. The energy of real valued sequence is given by __________ x(n) = {1, _, 3, _, 5, _, 7, _, 9, 10, _, 8, _, 6, _, 4, _, 2
2[1² + 2² + 3² + 4² + 5² + 6² + 7² + 8² + 9²] + 10²
10
10²
2[1² + 2² + 3² + 4² + 5² + 6² + 7² + 8² + 9² + 10²]