Question is ⇒ Electrical conductivity of metals expressed in ohm-1 m-1 is of the order of, Options are ⇒ (A) 1010, (B) 105, (C) 10-4, (D) 10-6, (E) , Leave your comments or Download question paper.

Question is ⇒ Electrical conductivity of metals expressed in ohm-1 m-1 is of the order of, Options are ⇒ (A) 1010, (B) 105, (C) 10-4, (D) 10-6, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Electrical conductivity of metals expressed in ohm^-1 m^-1 is of the order of
A.	10¹⁰ [Wrong Answer]
B.	10⁵ [Correct Answer]
C.	10^-4 [Wrong Answer]
D.	10^-6 [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : B Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The disadvantage of direct coupled amplifiers is
drift
large size of transistor
low voltage gain
both (b) and (c)

⇒ In an R-C circuit, the impedance is 40 Ω at a frequency of 100 Hz. At 200 Hz the impedance should be
40 Ω
80 Ω
20 Ω
more than 20 Ω but less than 40 Ω

⇒ The ac bridge in figure is balanced. Z₁ = 100∠30°, Z₂ = 150∠0°, Z₃ = 250∠ - 40° Then Z_{4375∠70° Ω
375∠ - 70° Ω
150∠0° Ω
150∠20° Ω}

⇒ The radiation resistance of a λ/16 wire dipole in free space will be nearly
1 Ω
3 Ω
13 Ω
30 Ω

⇒ Consider the following statements as regards IF in radio receivers

If IF is too high, poor selectivity and poor adjacent channel rejection could result
If IF is high, tracking difficulties increase
A very low IF makes selectivity too sharp
As IF is decreased, image frequency rejection becomes better

Which of the above are correct?
1, 2, 3, 4
1, 2, 3
2, 3, 4
1, 3, 4

⇒ For a n-channel JFET with r₀ = 10 kW, (V_Gs= 0 V, V_P = - 6 V)the drain resistance r_d at V_GS= - 3 V is given by
40 kΩ
2.5 kΩ
4.44 kW
120 kW

⇒ In envelope detection of an AM waveform
One side band and full-ampiitude carrier are needed
Both side bands and full-amplitude carrier are needed
Only two side bands are needed
Upper side band and part of carrier are needed

⇒ The most commonly used bias in BJT amplifier circuits is
voltage divider bias
emitter bias
collector bias
collector feedback bias

⇒ In a radio receiver, if the intermediate frequency is too low
Image-frequency rejection will improve
Selectivity will be too sharp
The frequency selectivity of the local oscillator will have to be lowered
All of the above

⇒ Two numbers in excess-3 code are added and the result is less than 8. To get equivalent binary
0011 is subtracted
0011 is added
0110 is subtracted
0110 is added

⇒ In SSB generation, the most commonly used filter is
low pass
RC
LC
mechanical

⇒ A rectifier circuit has load resistance R. It uses a capacitance filter having capacitance C. For low ripple in the output
RC should be 1
RC should be low
RC should be high
RC should be neither low nor high

⇒ When the modulating frequency is doubled, the modulation index is halved and the modulating voltage remains constant. The modulation system is
FM
AM
phase modulation
none of the above

⇒ A transmission line has a characteristic impedance of 50 Ω and a resistance of 0.1 Ω/m, if the line is distortion less, the attenuation constant (in Np/m) is
500
5
0.014
0.002

⇒ The number of programmable 8 bit registers of 6800 are
2
3
4
5

⇒ A mod-2 counter followed by a mod 5 is same as
mod-7 counter
A decade counter
mod-3 counter
none

⇒ The h parameter equivalent circuit of BJT has one voltage source and one current source.
TRUE
FALSE

⇒ In a transistor β_dc is likely to vary between 100 and 400. The proper value of β_dc to be used to located Q point is
100
400
250
200

⇒ The gauge factor of a semiconductor strain gauge is about
2
10
100
1000

⇒ For an amplifier the power gain in decibels will be equal to voltage gain in decibels only when
R₀ = 0
R₀ = R_i = 90
R₀ = R_i
R_i = 0

⇒ For free space propagation
γ = a + jβ
γ = jβ
γ = a
a = β = 0

⇒ In a ferromagnetic material, the internal field seen by a dipole is
equal to applied field
equal to applied field minus a contribution from neighbouring dipoles
equal to applied field plus a contribution from neighbouring dipoles
equal to or less than applied field

⇒ Bitter powder patterns prove the existence of domains.
TRUE
FALSE

⇒

Match the following:

	List I (Instrument)		List II (Measured quantity)
A.	Hot wire	1.	only voltage
B.	PMMC	2.	phase
C.	Electrostatic	3.	true RMS value
D.	Lock in Amplifier	4.	dc value

A-3, B-2, C-1, D-4
A-1, B-4, C-2, D-3
A-3, B-4, C-1, D-2
A-2, B-3, C-4, D-1

⇒ The gain of collinear arrays is maximum when the spacing between the elements is
0.1 λ to 0.3 λ
0.3 λ to 0.9 λ
0.5 λ to 0.7 λ
0.7 λ to 0.9 λ

⇒ Point out the false statem
Building, for the time, a body-stabilized geosynchronous communication satellite with its own apogee propulsion and control systems
Attitude control and station management operations for a geostationary satellite
Building launching rocket Ariane for putting APPLE in orbit
Domestic communications on an experimental basis

⇒ In a tungsten filament lamp
the current at the instant of switching is less than operating current
the current at the instant of switching is more than operating current
the current at the instant of switching is equal to operating current
the current at the instant of switching may be less than or equal to operating current

⇒ BCD equivalent of - 8₁₀ is
110
10110
11000
1000

⇒ In figure, the effective capacitance between A and
2 μF
4 μF
8 μF
10 μF

⇒ SSB-SC stands for
Single Side Band-Suppressed Carrier
Single Side Band-Synchronous Carrier
Synchronous Side Band-Suppressed Carrier
Synchronous Side Band-Self Carrier