Question is ⇒ ECL has high switching speed because the transistors are, Options are ⇒ (A) switching between cutoff and saturation regions, (B) switching between cutoff and active regions, (C) switching between active and saturation regions, (D) none of the above, (E) , Leave your comments or Download question paper.

Question is ⇒ ECL has high switching speed because the transistors are, Options are ⇒ (A) switching between cutoff and saturation regions, (B) switching between cutoff and active regions, (C) switching between active and saturation regions, (D) none of the above, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	ECL has high switching speed because the transistors are
A.	switching between cutoff and saturation regions [Wrong Answer]
B.	switching between cutoff and active regions [Correct Answer]
C.	switching between active and saturation regions [Wrong Answer]
D.	none of the above [Wrong Answer]
View Answer 2 -1 Explanation:- Answer : B Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ A coaxial RF cable has a characteristic impedance of 50 Ω and C equal to 40 pF/m. The inductance is
1 μ H/m
10 μ H/m
0.1 μ H/m
0.01 μ H/m

⇒ In a N-P-N transistor of the emitter junction is reverse biased and collector junction is also reversed biased, the transistor will operate in
active region
saturation region
cut-off region
inverted region

⇒ Tropospheric scatter propagation is not subject to any fading.
TRUE
FALSE

⇒ With 2's complement representation, the range of values that can be represented on the data bus of an 8 bit microprocessor is given by
-128 to 127
-128 to +128
-127 to 128
-256 to 256

⇒ A UJT exhibits negative resistance characteristics when
Current is less than valley current
Current is less than peak current
Current is more than peak current but less than valley current
None of the above

⇒ A dc chopper V = 500 V feeds an electric fraction dc series motor. The chopping frequency is 400 Hz. The series inductance required to limit the maximum current swing to 10 A is
20 mH
about 31 mH
about 51 mH
about 92 mH

⇒ In each of circuits below, indicate which diode is conduct
Figure A
Figure B
Figure C
All the three

⇒ Which of the following is an indirect method of generating FM?
Reactance BJT modulator
Armstrong modulation
Varactor diode modulation
Reactive FM modulator

⇒ The response of a function is decided by
the location of its zeros
the location of its poles
both (a) and (b)
none of the above

⇒ A mode-10 counter can divide the clock frequency by a factor of
10
100
1000
10000

⇒ For the K map of the given figure the simplified Boolean expressio
ACD + ABD + BCD
ACD + BCD
ACD + ABD
none of the above

⇒ Transverse magnetic (TM) waves have
magnetic field component H in the direction of propagation
electric field component E in the direction of propagation
magnetic field component H in the direction of propagation and no component of electric field E in this direction
electric field component E in the direction of propagation and no component of magnetic field H in this direction

⇒ In AM receiver the oscillator frequency is
always equal to signal frequency
always equal to 455 kHz
always higher than signal frequency
always lower than signal frequency

⇒ For the minterm designation Y = ∑ m (1, 3, 5, 7) the complete expression is
Y = A BC + A B C
Y = A B C + A B C + ABC + A BC
Y = A B C + A B C + ABC + A BC
Y = A B C + ABC + A BC + A BC

⇒ A series RL circuit is excited by a voltage v(t) = V_msin (ωt + Φ). The transient current will be zero if
Φ = 0
ω = 0
Φ = tan^-1 (ωL/R)
ω - tan^-1 (ωL/R) = p/2

⇒ In an hydrogen atom, an electron moves in the field of a proton. The stability of orbit requires equilibrium between coulomb's force and centrifugal force.
TRUE
FALSE

⇒ Power gain of antenna equals directive gain in VHF and UHF range if and only if efficiency of the antenna is
0.25
0.5
0.75
1

⇒ In a transmission line terminated with a load equal to the characteristic impedance, the reflection coefficient is
0
1
-1
Infinity

⇒ A second order active bandpass filter can be obtained by cascading LP second order filter having higher cut off frequency f_OH with a second order HP filter having lower cut off frequency f_OL provided
f_OL < f_OH
f_OL > f_OH
f_OH = f_OL
f_OH < 0.5 f_OL

⇒ In figure, V_EB = 0.6 V, β = 99. Then V_C and I_C
9.3 V and 1.98 mA respectively
4.6 V and 1.98 mA respectively
9.3 V and 0.02 mA respectively
4.6 V and 0.02 mA respectively

⇒ For a 400 kHz transmission line having L = 0.5 mH/km, C = 0.08 mF and negligible R and G, the value of propagation constant P will be
15.9 radians/km
31.8 radians/km
63.6 radians/km
105.4 radians/km

⇒ The analog signal given below is sampled by 600 samples per se
600 Hz
120 Hz
300 Hz
360 Hz

⇒

Assertion (A): Orbital magnetic moment of an electron in an atom is of the order of 1 Bohr magneton.

Reason (R): 1 Bohr magneton = 9.27 x 10^-24 A/m².

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not correct explanation of A
A is true but R is false
A is false but R is true

⇒ The drift velocity of electrons is
very small as compared to speed of light
equal to speed of light
almost equal to speed of light
half the speed of light

⇒ When a ferromagnetic substance is magnetised there are small changes in dimensions. This phenomenon is called
hysteresis
magnetostriction
diamagnetism
dipolar relaxation

⇒ The phase angle of lead circuit is
between 0 and -90°
between 0 and +90°
90°
more than 90°

⇒

Match the following:

	List I (Bits operator in C)		List II (Meaning)
A.	˜	1.	Bitwise XOR
B.	&	2.	Bitwise AND
C.	\|	3.	Bitwise OR
D.	U	4.	One's complement

A-1, B-2, C-3, D-4
A-4, B-3, C-2, D-1
A-2, B-3, C-1, D-4
A-4, B-2, C-3, D-1

⇒ Consider the following statements about data structures in Pascal

Arrays and files are types of data structures.
List structure is not a data structure in Pascal.
Each element of a binary tree is called a node of the tree.

Which of the above are statements correct?
All
1, and 2 only
1 and 3 only
2 and 3 only

⇒ The most serious problems in ac bridge measurement is
eddy currents
leakage current
residual magnetism
stray fields

⇒ Effective address is calculated by adding or subtracting displacement value to
immediate address
Relative address
absolute address
base address