Question is ⇒ During rheostatic braking the braking torque is proportional to, Options are ⇒ (A) speed, (B) (speed)2, (C) (speed)-1, (D) (speed)-2, (E) , Leave your comments or Download question paper.

Question is ⇒ During rheostatic braking the braking torque is proportional to, Options are ⇒ (A) speed, (B) (speed)2, (C) (speed)-1, (D) (speed)-2, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	During rheostatic braking the braking torque is proportional to
A.	speed [Correct Answer]
B.	(speed)² [Wrong Answer]
C.	(speed)^-1 [Wrong Answer]
D.	(speed)^-2 [Wrong Answer]
View Answer 11 -10 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The losses occurring in a D.C. generator are given below. Which loss is likely to have the least proportion ?
Magnetic losses
Armature copper losses
Mechanical losses
Field copper losses

⇒ Which of the following steps is likely to result in reduction of hysteresis loss in a D.C. generator ?
Providing laminations in armature core
Providing laminations in stator
Using non-magnetic material for frame
Using material of low hysteresis coefficient for armature core material

⇒ The purpose of retardation test on D.C. shunt machines is to find out
stray losses
eddy current losses
field copper losses
windage losses

⇒ In hazardous area of gassy mines, material transportation is done by vehicles powered by
A.C. mains
D.C. mains
I.C. engines
batteries

⇒ These days D.C. motors are widely used in
pumping sets
air compressors
electric traction
machine shops

⇒ The series parallel system of speed control of D.C. series motors widely used in traction work gives a speed range of about
1 : 10
1 : 8
1 : 6
1 : 4

⇒ In D.C. shunt motors as load is reduced
the speed will increase abruptly
the speed will increase in proportion to reduction in load
the speed will remain almost constant
the speed will reduce

⇒ The speed of a D.C. shunt motor can be increased by
increasing the resistance in armature circuit
increasing the resistance in field circuit
reducing the resistance in the field circuit
reducing the resistance in the armature circuit

⇒ The losses occurring in a D.C. generator are given below. Which loss is likely to have highest proportion at rated load of the generator ?
hysteresis loss
field copper loss
armature copper loss
eddy current loss

⇒ Which of the following statements is correct, in case of a D.C. series motor ?
It should be directly connected to the load
It may run away if its field becomes open
It is a constant speed motor
It cannot be used where high starting torque is required

⇒ Which of the following can be used for controlling the speed of a D.C. motor ?
Thermistor
Transistor
Thyratron
Thyristor

⇒ In an overloaded motor main danger arises due to
winding getting overheated
busbars getting heated
starter getting damaged
bearings getting overheated

⇒ Which D.C. motor will be preferred for machine tools ?
Series motor
Shunt motor
Cumulative compound motor
Differential compound motor

⇒ In a manual shunt motor starter
over load relay is connected in series and no volt relay in parallel with the load
over load relay is connected in parallel and no volt relay in series with the load
over load relay and no volt relay are both connected in series with the load
over load relay and no volt relay are both connected in parallel with the load

⇒ During rheostat braking of D.C. series motors
motor is run as a generator
motor is reversed in direction
motor is run at reduced speed

⇒ Which of the following can be used to control the speed of a D.C. motor ?
Thermistor
Thyristor
Thyratron
Transistor

⇒ Which loss in a D.C. generator does not vary with load as well as flux density ?
Copper loss
Eddy current loss
Hysteresis loss
Windage loss

⇒ The armature voltage control of D.C. motor provides
constant torque drive
constant voltage drive
constant current drive
none of the above

⇒ A face plate starter is employed for starting
induction motor
universal motor
synchronous motor
d.c. series motor

⇒ If the field of a D.C. shunt motor gets opened while motor is running
the speed of motor will be reduced
the armature current will reduce
the motor will attain dangerously high speed
the motor will continue to run at constant speed

⇒ The total losses in a well designed D.C. generator of 10 kW will be nearly
100 W
500 W
1000 W
1500 W

⇒ In a D.C. generator, the iron losses mainly take place in
yoke
commutator
armature conductors
armature rotor

⇒ Which method of braking is generally used in elevators ?
Plugging
Regenerative braking
Rheostatic braking
None of the above

⇒ A shearing machine has cyclic load consisting of intermittent light and henry loads. Which of the following D.C. motor will be suitable for this purpose?
Series motor
Shunt motor
Cumulative compound motor
Differential compound motor

⇒ When two D.C. series motors are connected in parallel, the resultant speed is
more than the normal speed
loss than the normal speed
normal speed
zero

⇒ During rheostatic braking the braking torque is proportional to
speed
(speed)²
(speed)^-1
(speed)^-2

⇒ Which one of the following is not necessarily the advantage of D.C. motors over A.C. motors ?
Low cost
Wide speed range
Stability
High starting torque

⇒ The variable resistor shunting the field of a D.C. series motor is called a
armature divertor
voltage regulator
field divertor
potential divider

⇒ When the speed of a D.C. motor increases
back e.m.f. increases and current drawn decreases
back e.m.f. as well as current drawn both increase
back e.m.f. as well as current drawn both decrease
back e.m.f. decreases and current drawn increases

⇒ In a D.C. shunt motor, under the conditions of maximum power, the current in the armature will be
almost negligible
rated full-load current
less than full-load current
more than full-load current