Question is ⇒ During compression stroke the air is compressed according to, Options are ⇒ (A) Isothermal process, (B) Hyperbolic process, (C) Adiabatic process, (D) Constant pressure process, (E) , Leave your comments or Download question paper.

Question is ⇒ During compression stroke the air is compressed according to, Options are ⇒ (A) Isothermal process, (B) Hyperbolic process, (C) Adiabatic process, (D) Constant pressure process, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	During compression stroke the air is compressed according to
A.	Isothermal process [Wrong Answer]
B.	Hyperbolic process [Wrong Answer]
C.	Adiabatic process [Correct Answer]
D.	Constant pressure process [Wrong Answer]
View Answer 12 -7 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ It is cheaper if we use gaskets of
Rubber asbestos type
Copper asbestos type
Steel asbestos type

⇒ The brake shoes are curved to conform to the inner diameter of the
Tyre
Wheel
Pedal
Brake drum

⇒ The weight or pressure required to deflect a spring in mm is called the spring
Weight
Deflection
Rate
Rebound

⇒ Aluminium alloy pistons are preferred because
They are good absorbers of shock
They are having less weight
They have good water resistance
They are very strong in tension

⇒ In a differential with a gear ratio of 4 : 1 the drive pinion would revolve four times to cause the ring gear to rotate
1 time
2 times
4 times
6 times

⇒ The working fluid normally used in hydraulic brake systems is
High speed diesel oil along with alcohol
SAE 20 oil with anti-corrosion additives
A mixture of vegetable oil and SAE 10 oil
A solution of castor oil in alcohol along with neutralizer

⇒ IHP minus FHP equals
BHP
SAF HP
m.e.p

⇒ Parts of the shock absorber include
Valves
Coupler
Valve springs
Pistons

⇒ The radiator tubes are manufactured by using
Cast iron tubes
Aluminum tubes
Brass tubes
Steel tubes

⇒ In a vacuum suspended unit, when the brakes are on, the piston or diaphragm has on both sides of it
Atmospheric pressure
Vacuum
Hydraulic pressure

⇒ Transmission noise in neutral could result from
Worn gears
Loose propeller shaft
Misadjusted gear linkage

⇒ The temperature of the piston will be more at
The piston walls
The crown of the piston
The skirt of the piston
The piston pin

⇒ The second movement of the gear shift lever produces
The correct gears to mesh
The movement of the drive gear
Release of clutch

⇒ On a straight road, the ring gear
Rotates at the same speed as wheels
Rotates faster than wheels
Rotates slower than wheels
Does not rotate

⇒ In a vehicle with torque tube drive, the rear suspension spring
Takes up driving thrust and torque reaction
Supports load and takes up end thrust
Takes up braking thrust and torque reaction
Takes up end thrust and torque reaction

⇒ The hydrodynamic torque converter
Gives a continuous variation of torque with increase of output speed
Enables to get the max. h.p continuously
Gives a speed variation without torque variation
Maintains a high efficiency throughout the operating speed range

⇒ The purpose of the fluid coupling is to act as a
Synchronizing device
Automatic gear changer
Flexible power-transmitting coupling

⇒ In the diesel engine, the compression ratio is as high as
10:1
15:1
5:1

⇒ The device for smoothing out the power impulses from the engine is called the
Flywheel
Camshaft
Crankshaft
Clutch

⇒ Vibration damper ..........
controls the torsional vibrations
drives the pulley
dampens the engine speed
reduces the speed of the flywheel

⇒ The compression ratio in a diesel engine is as high as
25:1
20:1
10:1
5:1

⇒ Immediately after ignition, combustion chamber temperatures may reach a value of
15000C
55000C
25000C
75000C

⇒ One of the major causes of FHP in an engine is
High speed
High volumetric efficiency
Piston-ring friction

⇒ If compression ratio is increased
Thermal efficiency will be increased
Volumetric efficiency will be increased
Air standard efficiency will be decreased
Air standard efficiency will be increased

⇒ The type of air cycle used in diesel engine is called
Otto cycle
Carnot cycle
Diesel cycle
Rankine cycle

⇒ The distance between adjacent meshing teeth of mating gears is called
Clearance
Back lash
Flank

⇒ The centre part of a typical universal joint is called the
Trunnion
Joint
Bearing
Spider

⇒ The temperature of the compressed air should be .............. of the fuel
Below the flash point
Above the flash point
Above the fire point
Between the fire and flash point

⇒ Differential mechanism at the axle is provided mainly to
Enable the vehicle go round corners
Equalize the division of torque between the two wheels c. To provide a reduction ratio
To turn the drive through a right angle

⇒ The coil spring clutch may use from
Two to six springs
Three to nine springs
Four to eight springs
Ten to twelve springs