Question is ⇒ Dielectric strength of rubber is around, Options are ⇒ (A) 5 kV/mm, (B) 15 kV/mm, (C) 30 kV/mm, (D) 200 kV/man, (E) , Leave your comments or Download question paper.

Question is ⇒ Dielectric strength of rubber is around, Options are ⇒ (A) 5 kV/mm, (B) 15 kV/mm, (C) 30 kV/mm, (D) 200 kV/man, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Dielectric strength of rubber is around
A.	5 kV/mm [Wrong Answer]
B.	15 kV/mm [Wrong Answer]
C.	30 kV/mm [Correct Answer]
D.	200 kV/man [Wrong Answer]
View Answer 10 -8 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Copper as conductor for cables is used as
annealed
hardened and tempered
hard drawn
alloy with chromium

⇒ Which of the following protects a cable against mechanical injury ?
Bedding
Sheath
Armouring
None of the above

⇒ Empire tape is
varnished cambric
vulcanised rubber
impregnated paper
none of the above

⇒ The minimum dielectric stress in a cable is at
armour
bedding
conductor surface
lead sheath

⇒ The bedding on a cable consists of
hessian cloth
jute
any of the above
none of the above

⇒ Is a cable is to be designed for use on 1000 kV, which insulation would you prefer ?
Polyvinyle chloride
Vulcanised rubber
Impregnated paper
Compressed SF6 gas

⇒ The thickness of metallic shielding on cables is usually
0.04 mm
0.2 to 0.4 mm
3 to 5 mm
40 to 60 mm

⇒ In capacitance grading of cables we use a ____ dielectric.
composite
porous
homogeneous
hygroscopic

⇒ The insulating material for a cable should have
low cost
high dielectric strength
high mechanical strength
all of the above

⇒ Which of the following insulation is used in cables ?
Varnished cambric
Rubber
Paper
Any of the above

⇒ A cable carrying alternating current has
hysteresis losses only
hysteresis and leakage losses only
hysteresis, leakage and copper losses only
hysteresis, leakage, copper and friction losses

⇒ The insulating material for cables should
be acid proof
be non-inflammable
be non-hygroscopic
have all above properties

⇒ A certain cable has an insulation of relative permittivity 4. If the insulation is replaced by one of relative permittivity 2, the capacitance of the cable will become
one half
double
four times
none of the above

⇒ In the cables, sheaths are used to
prevent the moisture from entering the cable
provide enough strength
provide proper insulation
none of the above

⇒ ____ cables are used for 132 kV lines.
High tension
Super tension
Extra high tension
Extra super voltage

⇒ The thickness of the layer of insulation on the conductor, in cables, depends upon
reactive power
power factor
voltage
current carrying capacity

⇒ PVC stands for
polyvinyl chloride
post varnish conductor
pressed and varnished cloth
positive voltage conductor

⇒ In the cables, the location of fault is usually found out by comparing
the resistance of the conductor
the inductance of conductors
the capacitances of insulated conductors
all above parameters

⇒ The insulating material should have
low permittivity
high resistivity
high dielectric strength
all of the above

⇒ In case of three core flexible cable the colour of the neutral is
blue
black
brown
none of the above

⇒ If a cable of homogeneous insulation has a maximum stress of 10 kV/mm, then the dielectric strength of insulation should be
5 kV/mm
10 kV/mm
15 kV/mm
30 kV/mm

⇒ Solid type cables are considered unreliable beyond 66 kV because
insulation may melt due to higher temperature
of corona loss between conductor and sheath material
there is a danger of breakdown of insulation due to the presence of voids

⇒ Cables, generally used beyond 66 kV are
oil filled
S.L. type
belted
armoured

⇒ High tension cables are generally used upto
11 kV
33 kV
66 kV
132 kV

⇒ The advantage of cables over overhead transmission lines is
easy maintenance
low cost
can be used in congested areas
can be used in high voltage circuits

⇒ Conduit pipes are normally used to protect ____ cables.
unsheathed cables
armoured
PVC sheathed cables
all of the above

⇒ In a cable immediately above metallic sheath ____ is provided.
earthing connection
bedding
armouring
none of the above

⇒ Low tension cables are generally used upto
200 V
500 V
700 V
1000 V

⇒ The electrostatic stress in underground cables is
same at the conductor and the sheath
minimum at the conductor and maximum at the sheath
maximum at the conductor and minimum at the sheath
zero at, the conductor as well as on the sheath

⇒ Dielectric strength of rubber is around
5 kV/mm
15 kV/mm
30 kV/mm
200 kV/man