Question is ⇒ Detailed plotting is generally done by, Options are ⇒ (A) radiation, (B) traversing, (C) resection, (D) all of the above, (E) , Leave your comments or Download question paper.

Question is ⇒ Detailed plotting is generally done by, Options are ⇒ (A) radiation, (B) traversing, (C) resection, (D) all of the above, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Detailed plotting is generally done by
A.	radiation [Correct Answer]
B.	traversing [Wrong Answer]
C.	resection [Wrong Answer]
D.	all of the above [Wrong Answer]
View Answer 34 -7 Explanation:- Answer : A Discuss it below : Amjad Ali Said on 2020-02-15 16:11:43 Generally the radiation and intersection methods are the detailed plotting methods Mudassar Nazir Said on 2019-10-07 06:40:30 Plotting is done by radiation method and angular measurements are found by techometry Himendra Katakwar Said on 2019-02-28 19:51:56 Plz explained it.. !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Which of the following introduces an error of about 1 in 1000 if 20 m chain is used.
length of chain 20 mm wrong
one end of the chain 0.9 m off the line
one end of chain 0.9 m higher than the other
all the above.

⇒ For preparation of a contour plan for a route survey.
method of squares is used
method of trace contour is used
method of cross profile is used
indirect method of contouring is used.

⇒ If D is the degree of the curve of radius R, the exact length of its specified chord, is.
radius of the curve x sine of half the degree
diameter of the curve x sine of half the degree
diameter of the curve x cosine of half the degree
diameter of the curve x tangent of half the degree.

⇒ Pick up the correct statement from the following :
The horizontal angle between magnetic meridian and true meridian at a place is called magnetic declination or variance of the compass
the imaginary lines which pass through points at which the magnetic declinations are equal at a given time are called isogonic lines
the isogonic lines through places at which the declination is zero are termed agonic lines
all the above.

⇒ A triangle is said to be well conditioned if none of its angles is less than
20°
30°
45°
60°

⇒ Diopter is the power of a lens having a focal length of.
25 cm
50 cm
75 cm
125 cm

⇒ Offsets are measured with an accuracy of 1 in 40. If the point on the paper from both sources of error (due to angular and measurement errors) is not to exceed 0.05 cm on a scale of 1 cm = 20 m, the maximum length of offset should be limited to.
14.14
28.28 m
200 m
none of these.

⇒ The accuracy of measurement in chain surveying, does not depend upon.
length of the offset
scale of the plotting
importance of the features
general layout of the chain lines.

⇒ Magnetic meridian and true meridian are
Always parallel
Parallel at the equator
Parallel near the poles
Never parallel

⇒ Pick up the correct statement from the following :
A level surface is perpendicular at all points to the direction of gravity
A level line lies in level surface
A horizontal surface is normal to the direction of gravity at only one point
All the above.

⇒ The bearing of line AB is 152° 30' and angle ABC measured clockwise is 124° 28'. The bearing of BC is.
27Â° 52'
96Â° 58'
148Â° 08'
186Â° 58'

⇒ Deviation of the actual road gradient from the proposed contou'r gradient up hill side, involves.
embankment on the centre line
excavation on the centre line
earth work on the centre line
none of these.

⇒ The method generally preferred to for contouring an undulating area, is.
chain surveying
plane table surveying
tacheometrical surveying
compass surveying.

⇒ For a well-conditioned triangle, no angle should be less than
20°
30°
45°
60°

⇒ The construction of optical square is based, on the principle of optical.
reflection
refraction
double refraction
double reflection.

⇒ The bearings of the lines AB and BC are 146° 30' and 68° 30'. The included angle ABC is.
102Â°
78Â°
45Â°
none of these.

⇒ In an adjusted level, when the bubble is central, the axis of the bubble tube becomes parallel to.
line of sight
line of collimation
axis of the telescope
None of these.

⇒ The angle of intersection of a contour and a ridge line, is.
30Â°
45Â°
60Â°
90Â°.

⇒ The difference between a level line and a horizontal line is that
level line is a curved line while hori-zontal line is a straight line
level line is normal to plumb line while horizontal line may not be normal to plumb line at the tangent point to level line
horizontal line is normal to plumb line while level line may not be normal to the plumb line
both are same

⇒ If the length of a chain is found to be short on testing, it can be adjusted by
straightening the links
removing one or more small circular rings
closing the joints of the rings if opened out
all of the above

⇒ The horizontal angle between true meridian and magnetic meridian, is known.
bearing
magnetic declination
dip
convergence.

⇒ Benchmark is established by
hypsometry
barometric levelling
spirit levelling
trigonometrical levelling

⇒ The difference between the included angle and 180°.
vision gets obstructed
chaining gets obstructed
both vision and chaining get obstructed
all the above.

⇒ The magnetic bearing of a line is 32° and the magnetic declination is 10° 15' W. The true bearing is.
21Â° 45'
42Â° 15'
42Â° 15' W
21Â° 45' W

⇒ In levelling operation.
if second reading is more than first, it represents a rise
if first reading is more than second, it represents a rise
if first reading is less than second, it represents a fall
both (b) and (c).

⇒ Number of links per metre length of a chain are.
2
5
8
10

⇒ If n is the number of sides then the total sum of exterior angles of a closed traverse should be
n + 2
2n - 4
2n + 4
4n - 2

⇒ Pick up the correct statement from the following :
the diaphragm is placed between eyepiece and the objective but nearer to the former
the diaphragm is placed between the eyepiece and objective but nearer to the later
the outer component of the objective is a double-convex lens of crown glass
all the above.

⇒ In tangential tacheometry, an ordinary level staff is used.
leaning towards the instrument for inclined sights upward
leaning away from the instrument for inclined sights downwards
vertical in all cases
none of these.

⇒ Straight, parallel and widely spaced contours represent.
a steep surface
a flat surface
an inclined plane surface
curved surface.