Users Also Read

MCQ's Search Engine

Electrical Engineering

Mechanical Engineering

Civil Engineering

Automobile Engineering

Chemical Engineering

Computer Engineering

Electronics Engineering

Medical Science Engg

Q1. | Degree of static indeterminacy of a rigid-jointed plane frame having 15 members, 3 reaction components and 14 joints is |

A. | 2 [Wrong Answer] |

B. | 3 [Wrong Answer] |

C. | 6 [Correct Answer] |

D. | 8 [Wrong Answer] |

View Answer
Explanation:-
Answer : CDiscuss it below :SHAMS UR REHMAN Said on 2019-11-30 00:19:57Option C is the right answer. as S.I for rigid jointed frame structure is S.i= 3m+r-3j =3*15+3-3*14=48-42=6 !! OOPS Login [Click here] is required to post your answer/resultHelp other students, write article, leave your comments |

**Also Read Similar Questions Below :**

⇒ The basic stress in masonry units having height to width ratio of 1.5 may be increased by a factor of

1.2

1.4

1.6

2.0

⇒ In the case of panel wall subjected to horizontal loads at right angles to the plane of the wall, with the mortar not leaner than Ml type, tensile stress in bending in the vertical direction may be allowed to the extent of

0.4 kg/cm2

0.7 kg/cm2

1.0 kg/cm2

1.2 kg/cm2

⇒ The horizontal thrust due to rise in temperature in a semicircular two-hinged arch of radius R is proportional to

R

R

^{2}

1/R

1/R

^{2}

⇒ For a two-hinged arch, if one of the supports settles down vertically, then the horizontal thrust

is increased

is decreased

remains unchanged

becomes zero

⇒ In the displacement method of structural analysis, the basic unknowns are

displacements

force

displacements and forces

none of the above

⇒ The number of independent equations to be satisfied for static equilibrium of a plane structure is

1

2

3

6

⇒ The mode of failure of a very short masonry member having h/t ratio of less than 4 is by

shear

vertical tensile splitting

buckling

any of the above

⇒ The thickness of each leaf of a cavity wall shall not be less than

5 cm

7.5 cm

10 cm

15 cm

⇒ Unequal settlements in the supports of a statically indeterminate structure develop

Member forces

Reactions from supports

No reactions

Strains in some members only

⇒ The method of virtual work in the analysis of structures results is

Compatible deformations

Equilibrium of forces

Stress strain relations

None of these

⇒ The number of independent equations to be satisfied for static equilibrium in a space structure is

2

3

4

6

⇒ A free standing brick wall 20 cm thick is subjected to a wind pressure of 75kg/m2. The maximum height of wall from stability consideration is

0.64 m

0.96 m

1.28 m

1.5 m

⇒ In column analogy method, the area of an analogous column for a fixed beam of span L and flexural rigidity El is taken as

L/EI

L/2EI

L/3EI

L/4EI

⇒ When a load crosses a through type Pratt truss in the direction left to right, the nature of force in any diagonal member in the left half of the span would

change from compression to tension

change from tension to compression

always be compression

always be tension

⇒ Which of the following is not the displacement method ?

Equilibrium method

Column analogy method

Moment distribution method

Kani's method

⇒ The fixed support in real beam becomes in the conjugate beam is

Fixed support

Hinged support

Roller support

Free support

⇒ The force method in structural analysis always ensures

Equilibrium

Kinematically admissible t'orces

Equilibrium of forces

None of the above

⇒ For a symmetrical two hinged parabolic arch, if one of the supports settles horizontally, then the horizontal thrust

is increased

is decreased

remains unchanged

becomes zero

⇒ Number of unknown internal forces in each member of a rigid jointed plane frame is

1

2

3

6

⇒ A load 'W is moving from left to right support on a simply supported beam of span T. The maximum bending moment at 0.4 1 from the left support is

0.16 Wl

0.20 Wl

0.24 Wl

0.25 Wl

⇒ The degree of static indeterminacy up to which column analogy method can be used is

2

3

4

unrestricted

⇒ The maximum bending moment due to a train of wheel loads on a simply supported girder

always occurs at center of span

always occurs under a wheel load

never occurs under a wheel load

none of the above

⇒ The number of independent displacement components at each joint of a rigid-jointed space frame is

1

2

3

6

⇒ When a uniformly distributed load, longer than the span of the girder, moves from left to right, then the maximum bending moment at mid section of span occurs when the uniformly distributed load occupies

less than the left half span

whole of left half span

more than the left half span

whole span

⇒ For a single point load W moving on a symmetrical three hinged parabolic arch of span L, the maximum sagging moment occurs at a distance x from ends. The value of x is

0.211 L

0.25 L

0.234 L

0.5 L

⇒ The moment distribution method in structural analysis can be treated as

Force method

Displacement method

Flexibility method

None of these

⇒ Water retentivity for brick masonry should not be less than

50%

60%

70%

80%

⇒ To generate the j th column of the flexibility matrix

a unit force is applied at coordinate j and the displacements are calculated at all coordinates

a unit displacement is applied at co-ordinate j and the forces are calculated at all coordinates

a unit force is applied at coordinate j and the forces are calculated at all coordinates

a unit displacement is applied at co-ordinate j and the displacements are calculated at all co-ordinates

⇒ The moment area theorems in the structural analysis fall in the category of

Force method

Displacement method

Stiffness method

Iterative method

⇒ For masonry work with solid bricks, consistency of mortar should be

5 to 8 cm

9 to 13 cm

14 to 18 cm

19 to 23 cm