Question is ⇒ Decimal number 46 in excess 3 code =, Options are ⇒ (A) 1000 1001, (B) 0111 1001, (C) 0111 1111, (D) 1000 1111, (E) , Leave your comments or Download question paper.

Question is ⇒ Decimal number 46 in excess 3 code =, Options are ⇒ (A) 1000 1001, (B) 0111 1001, (C) 0111 1111, (D) 1000 1111, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Decimal number 46 in excess 3 code =
A.	1000 1001 [Wrong Answer]
B.	0111 1001 [Correct Answer]
C.	0111 1111 [Wrong Answer]
D.	1000 1111 [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : B Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Which TM mode in rectangular waveguide has lowest cutoff frequency?
TM₁₁
TM₀₁
TM₁₀
TM₂₁

⇒ A pulse transformer uses
ferrite core
air core
iron core
copper core

⇒ Both OR and AND gates can have only two inputs.
TRUE
FALSE

⇒ In low pass filter of figure R₀ = 1 Ω and cut off frequency is 1 rad/sec. The values of L and C
1 H and 2 F
1 H and 1 F
2 H and 1 F
1 H and 2 F

⇒ The eigen values of a skew symmetric matrix are
always zero
always pure imaginary
either zero or pure imaginary
always real

⇒ The number of valence electrons in silicon atom is
4
2
1
zero

⇒

Assertion (A): Impedance matching can be done by using stubs.

Reason (R): A double stub is used for impedance matching when frequency of signal varies.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct but R is wrong
A is wrong but R is correct

⇒

Assertion (A): Feedback control systems offer more accurate control than open loop systems.

Reason (R): The feedback path establishes a link for comparison of input and output and subsequent error correction.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct but R is wrong
R is correct but A is wrong

⇒

Assertion (A): The behaviour of FET is similar to that of a pentode.

Reason (R): FETs and vacuum triode are voltage controlled devices.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not a correct explanation of A
A is true but R is false
A is false but R is true

⇒ The graph of a network has 6 branches with 3 tree branches. The minimum number of equations required for solution of network is
2
3
4
5

⇒ As temperature increases
the forbidden energy gap in silicon and germanium increase
the forbidden energy gap in silicon and germanium decrease
the forbidden energy gap in silicon decreases while that in germanium decreases
the forbidden energy gap in silicon increases while that in germanium decreases

⇒ For the given truth table, the correct Boolean expressio
XYZ + X YZ + X Y Z
X Y Z + XYZ + X YZ
X Y Z + XYZ + XY Z
XYZ + XYZ + XY Z

⇒

Match the following:

	List I		List II
A.	h_ie	1.	49
B.	h_re	2.	25 x 10^-6siemens
C.	h_fe	3.	2.4 x 10^-4
D.	h_oe	4.	1000 ohms

A-1, B-2, C-3, D-4
A-4, B-3, C-2, D-1
A-3, B-4, C-1, D-2
A-4, B-3, C-1, D-2

⇒ The reflection coefficient on a 500 m long transmission line has a phase angle of - 150°. If the operating wavelength is 150 m, what will be the number of voltage maxima on the line?
0
3
6
7

⇒ Boolean expression for the output of XNOR (Equivalent) logic gate with inputs A and B is
AB + AB
AB + AB
(A + B). (A + B)
(A + B). (A + B)

⇒ When negative feedback is used the fractional changes in closed loop gain are desensitized by the factor (1 + A_vβ)
TRUE
FALSE

⇒ Which of the following directives in 8085 causes one byte to be reserved in the memory?
D S
D B
D W
E Q U

⇒ In AM receiver the oscillator frequency is
always equal to signal frequency
always equal to 455 kHz
always higher than signal frequency
always lower than signal frequency

⇒

Assertion (A): Hay's bridge in particularly suitable for measuring inductance having a comparatively low resistance.

Reason (R): In Hay's bridge the value of frequency supply must be known.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not correct explanation of A
A is true R is false
A is false R is true

⇒ The organisatioion of Intel memory chip 127256 is
32 K x 8
16 K x 8
32 K x 4
16 K x 4

⇒ If interrupt service request have been received from all of the following interrupts, then which one will be serviced last?
RST 5.5
RST 6.5
RST 7.5
None of these

⇒

Match the following:

	List I		List II
A.	Mu Metal	1.	very high magnetic permeability
B.	Samrium/cobalt	2.	very high magnetic remanence
C.	Sapphire	3.	very high thermal conductivity
D.	Ferrites	4.	very stable magnetic permeability

A-1, B-2, C-3, D-4
A-3, B-4, C-1, D-2
A-2, B-3, C-4, D-1
A-4, B-1, C-2, D-3

⇒ Consider the following statements:

If any root of characteristic equation has a positive real part the impulse response is unbounded and system is unstable.
If all the roots of a characteristic equation have negative real parts, the impulse response decays to zero.
If one or more non-repeated roots of characteristic equation are on jω axis impulse response is bounded but the system is unstable.

Which of the above equations are correct?
1, 2 and 3
1 and 2 only
1 and 3 only
2 and 3 only

⇒ The characteristic impedance of a twin wire feeder used for TV signals is about
1000 ohm
500 ohm
300 ohm
100 ohm

⇒ Stray capacitance is important at low frequencies.
TRUE
FALSE

⇒ Z_L = 200 Ω and it is desired that Z_i = 50 Ω The quarter wave transformer should have a characteristic impedance of
100 Ω
40 Ω
10000 Ω
4 Ω

⇒ The 2 out of 5 code has
two 0s and three 0s in each code group
one 1s and four 0s in each code group
four 1s and one 0s in each code group
three 1s and two 0s in each code group

⇒ Find equivalent capacitance if each capacitance is
5/12 F
12/5 F
6/5 F
5/6 F

⇒ Fourier transform pair are
autocorrelation and power spectral density
autocorrelation and convoloution
convolution and power spectral density
autocorrelation and energy

⇒ ECL can be used to high frequencies in the order of
500 kHz
1 MHz
100 MHz
500 MHz