Question is ⇒ Consider the following statements <ol style="list-style-type: decimal; padding-bottom:10px;"><li style="padding-top:10px;"> ECL has least propagation delay</li><li style="padding-top:10px;">TTL has largest fan out</li><li style="padding-top:10px;">CMOS has highest noise margin</li><li style="padding-top:10px;">TTL has lowest power dissipation</li></ol> Which of these are correct?, Options are ⇒ (A) 1 and 3, (B) 2 and 4, (C) 3 and 4, (D) 1 and 2, (E) , Leave your comments or Download question paper.

Question is ⇒ Consider the following statements <ol style="list-style-type: decimal; padding-bottom:10px;"><li style="padding-top:10px;"> ECL has least propagation delay</li><li style="padding-top:10px;">TTL has largest fan out</li><li style="padding-top:10px;">CMOS has highest noise margin</li><li style="padding-top:10px;">TTL has lowest power dissipation</li></ol> Which of these are correct?, Options are ⇒ (A) 1 and 3, (B) 2 and 4, (C) 3 and 4, (D) 1 and 2, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Consider the following statements ECL has least propagation delay TTL has largest fan out CMOS has highest noise margin TTL has lowest power dissipation Which of these are correct?
A.	1 and 3 [Correct Answer]
B.	2 and 4 [Wrong Answer]
C.	3 and 4 [Wrong Answer]
D.	1 and 2 [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ For a depletion type NMOS, V_p = - 4 volts. For V_GS = 0, 1_D = 16 mA in the pinch off region of V_DS. For V_GS = - 2, the value of I_D in the pinch off region of V_DS is given by
64 mA
32 mA
16 mA
4 mA

⇒ In figure, V_CC = + 30 V, R₁ = 200 kΩ and R₂ = 100 kΩ. If V_BE = 0.7 V, the voltage a cross R_{E+20 V
+19.3 V
+10 V
+9.3 V}

⇒ Which of the following is type declaration statement in C?
int bar
s = s + 1
king = horse + 1
prin = prin * prin

⇒

Match the following:

	List I (Functional components)		List II (Device)
A.	Error detector	1.	Three phase FHP Induction motor
B.	Servo motor	2.	Synchro transmitter and control transformer
C.	Amplifier	3.	Tacho generator
D.	Feed back	4.	Armature controlled FHP dc motor
		5.	Amplidyne

A-2, B-4, C-1, D-5
A-4, B-2, C-5, D-3
A-2, B-4, C-5, D-3
A-1, B-2, C-3, D-5

⇒ For measuring a very high resistance we should use
Kelvin's double bridge
Wheatstone bridge
Meggar
Either (a) or (c)

⇒ In degenerate p type semiconductor material, the Fermi level,
is in the valence band
is in conduction band
is at the centre in between valence and conduction bands
is very near conduction band

⇒ When Schrodinger equation is applied to the motion of electron in the field of protons, the physically acceptable solutions for the wave function exist for quantum number which are
2
3
4
5

⇒

Assertion (A): Different symbols are used for different gates

Reason (R): IEEE symbols are the same as traditional symbols for gates.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is true, R is false
A is false, R is true

⇒ The number of valence electrons in pentavalent impurity is
5
4
3
1

⇒ Choose correct option for a stable system :

Roots of the characteristic equation of the system are real and negative
Area within the impulse response is finite

I is true, II is true
I is true, II is false
I is false, II is true
I is false, II is false

⇒ Reflectors and lens antennas are commonly used
in LF communication systems
not beyond 100 kHz
in the range 10 MHz to 100 MHz
above 100 MHz

⇒ In a half wave voltage doubler circuit the input frequency is 50 Hz. The ripple frequency is
25 Hz
50 Hz
100 Hz
150 Hz

⇒ In figure V_BE = 0.7 V. If base current required to saturate the transistor is 0.1 mA, V_{i5 V
5.7 V
10 V
10.7 V}

⇒ A coil is wound having a diameter d. Its inductance is 10 mH. If it is rewound on the same core with a wire having diameter 0.5 d and total weight of the wire is the same as before, the inductance will be
5 mH
10 mH
160 mH
40 mH

⇒ Which is known as flash converter?
Weighted resistor D/A converter
Parallel A/D converter
Stair step A/D converter
Up-down counter type A/D converter

⇒ Gold is often diffused into silicon PN junction devices to
increase the recombination rate
reduce the recombination rate
make silicon a direct gap semiconductor
make silicon semimetal

⇒ In a CRO the Y plates are oriented
horizontally
vertically
at an angle of 20° of horizontal
at an angle of 70° of horizontal

⇒

Assertion (A): The data bus and address bus of 8085 are multiplexed.

Reason (R): Multiplexing reduces the number of pins.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct R is wrong
A is wrong R is correct

⇒ In a CRO, the time base signal is applied to
X plates
Y plates
either X or Y plates
alternately X and Y plates

⇒ In measurements using strain gauge, the dummy strain gauge is used to
compensate for resistance of strain gauge
compensate for change in temperature
compensate for error due to change in voltage of battery
compensate for error in voltmeter

⇒ In PCM, the biggest disadvantage as compared to AM is
larger bandwidth
larger noise
inability to handle analog signals
incompatibility with time division multiplex systems

⇒ The I/P impedance of a short circuited quarter wave long transmission line is
purely reactive
purely resistive
depend on the characteristic impedance of the line
none of the above

⇒

Assertion (A): In design of circuit using BJT, a derating factor is used.

Reason (R): As the ambient temperature increases, heat dissipation becomes slower.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not a correct explanation of A
A is true but R is false
A is false but R is true

⇒ The logic circuit given below converts a binary code y₁ y₂, y₃
Excess - 3 code
Gray code
BCD code
Hamming

⇒ A duplexer is a device used to
feed more than one receiver from a single antenna
connect two transmitters to the same antenna
connect a receiver and a transmitter to the same antenna
none of these

⇒ The maximum effective aperture of λ/2 (half-wave) antenna is
0.013 λ²
0.13 λ²
1.3 λ²
13 λ²

⇒ In an RL series circuit the inductance is 1H and current at an instant is 0.6 A. The energy stored in magnetic field is
0.36 J
0.18 J
0.09 J
0.03 J

⇒ The input to a parity detector is 1001. The output is
0
1
0 or 1
indeterminate

⇒ Dolby system of noise reduction divides the total audio spectrum into
8 frequency bands
4 frequency bands
2 frequency bands
none of the above

⇒ The switch board instruments
should be mounted in vertical position
should be mounted in horizontal position
should be mounted at about 45°
should be mounted at about 80°