Users Also Read

MCQ's Search Engine

Electrical Engineering

Mechanical Engineering

Civil Engineering

Automobile Engineering

Chemical Engineering

Computer Engineering

Electronics Engineering

Medical Science Engg

Q1. | Consider a 565 PLL with R_{T} = 10 kΩ and C_{T} = 0.01 μF. What is the output frequency of the VCO? |

A. | 10 kHz [Correct Answer] |

B. | 5 kHz [Wrong Answer] |

C. | 2.5 kHz [Wrong Answer] |

D. | 1.25 kHz [Wrong Answer] |

View Answer
Explanation:-
Answer : ADiscuss it below :!! OOPS Login [Click here] is required to post your answer/resultHelp other students, write article, leave your comments |

**Also Read Similar Questions Below :**

⇒ A voltage v = 5 + 50 sin ω

*t*/ + 5 sin 5 &omega

*t*is applied to a pure capacitor of capacitance 1 ωF. If

*f*/= 314 rad/sec, current is

1 + 0.0157 cos 314

*t*+ 0.00785 cos 1570

*t*

0.0157 cos 314

*t*+ 0.00785 cos 1570 t

0.0157 sin 314

*t*+ 0.00785 sin 1570

*t*

0.0157 sin (314

*t*/ + 45°) + 0.00785 sin (1570

*t*+ 45°)

⇒ If the voltage across the last resistor is V, and all the resistor is unity. Then V

_{s}is give

8 V

4 V

13 V

0

⇒ The two terms used to describe performance of a directional coupler are

coupling and directivity

gain and coupling

gain and directivity

gain and isolation

⇒ The cut off wavelength in circular waveguide

guide diameter

square of guide diameter

cube of guide diameter

square root of guide diameter

⇒ A satellite that simply reflect back the signals from one region of the earth to the other region is known as

orbiting satellite

geostationary satellite

active satellite

passive satellite

⇒ For oscillations to starts, the loop gain A β of the oscillator must be initially

less than unity

0.5

1

more than unity

⇒ In a transistor push pull amplifier

there is no dc present in the output

there are no even harmonics in the output

both (a) and (b)

neither (a) nor (b)

⇒ An input voltage V(

*t*) = 10 2 cos (

*t*+ 10°) + 10 3 cos (2

*t*+ 10°)

*V*is applied to a series combination of resistance R = 1 kΩ inductance L = 1H. The resulting steady-state current

*i*(

*t*) in ampere is

10 cos (

*t*+ 55°) + 10 cos (2

*t*+ 10° tan

^{-1}2)

10 cos (

*t*+ 55°) + 103/2 cos (2

*t*+ 55°)

10 cos (

*t*- 35) + 10 cos (2

*t*+ 10° - tan

^{-1}2)

10 cos (

*t*- 35) + 103/2 cos (2

*t*+ 35°)

⇒ In a flip-flop with a NAND latch, a low

*R*and a low

*S*produces

active condition

inactive condition

race condition

dead condition

⇒ By connecting external resistances to a differential amplifier we can adjust

voltage gain

bandwidth

both voltage gain and bandwidth

none of the above

⇒ The logic operations of the two circuits given below

complementary

identical

entirely different

none of these

⇒ The minimum number of comparators required to build an 8 bit flash ADC is

8

63

255

256

⇒ Consider the following; for a loss-less transmission line we can write,

- Z
_{in}= -*jz*_{0}for a shorted line with*l*= λ/8 - Z
_{in}= ±*j*∞ for a shorted line with*l*= λ/4 - Z
_{in}=*jz*_{0}for an open line with*l*= λ/2 - Z
_{in}= 0 for a matched line of any length

1, 2

2, 3

1, 3

2, 4

⇒ In ionosphere incidence angle is 60°. The maximum usable frequency

*f*is equal to

_{m}2

*f*

_{c}*f*

_{c}0.5

*f*

_{c}3

*f*

_{c}⇒

**Assertion (A):** In a BCD to 7 segment decoder the number of outputs active at one time is always the same.

**Reason (R):** A decoder can be used to interface BCD input to LED display.

Both A and R are correct and R is correct explanation of A

Both A and R are correct but R is not correct explanation of A

A is true, R is false

A is false, R is true

⇒ A transistor has two

*p*-

*n*junctions. The batteries should be connected such that

both junctions are forward biased

both junctions are reverse biased

one junction is forward biased and the other is reverse biased

either (a) or (b)

⇒ The main advantage of TWT over klystron is

higher bandwidth

higher gain

higher frequency

higher output

⇒ The register set and instruction set of 8088 is similar to that of

8085

8086

partly 8085 and partly 8086

none of the above

⇒ When a high voltage reference is required it is advantageous to use two or more zener diodes in series to allow

higher voltage

higher dissipation

lower temperature coefficient

all of the above

⇒ An advantage of memory interlacing is that

a larger memory is obtained

effective speed of memory is increased

cost of memory is reduced

a non-volatile memory is obtained

⇒ In a conductor which of the following relations hold good?

∇ x D = r

∇ . D = r

∇ x D = 0

∇ . D = 0

⇒ As regards ∈

_{0}and ∈

_{r}(absolute and relative permittivity)

both ∈

_{0}and ∈

_{r}can be interpreted in terms of atomic properties of medium

only ∈

_{r}can be interpreted in terms of atomic properties of medium

only ∈

_{0}can be interpreted in terms of atomic properties

∈

_{r}has no physical significance

⇒ Consider the following logical IF statement in FORTRAN 77

IF (SALT - PEPPER) 11, 11, 13

IF (SALT - PEPPER) 11, 13, 13

IF (SALT - PEPPER) 13, 11, 11

⇒ For an RC impedance function

all poles lie on

*j*ω axis

all poles are simple ,

all poles are simple and lie on negative real axis

none of the above

⇒

Match the following:

List I (Amplifier coupling) | List II (Feature) | ||
---|---|---|---|

A. | RC | 1. | High voltage gain and impedance matching |

B. | Inductive | 2. | Ability to amplify dc and low frequency signals |

C. | Transformer | 3. | Minimum non-linear distortion |

D. | Direct | 4. | Low collector supply voltage can be used |

A-4, B-1, C-3, D-2

A-3, B-4, C-1, D-2

A-1, B-2, C-3, D-4

A-4, B-3, C-2, D-1

⇒ The diameter of an atom is

10

^{-6}metre

10

^{-10}metre

10

^{-15}metre

10

^{-21}metre

⇒ The root locus branches

start from open loop poles and terminate at zeros

start from open loop zeros and terminate at poles

may start from pole or zero and terminate at another pole or zero

none of the above

⇒ A resistance of 5 ohms is connected in one branch of a network. The current in this branch is 2.2. A. If the resistance is increased to 7.5 Ω, the remaining circuit being the same, the current in this branch will be

2.2 A

less than 2.2 A

2.2 A or less than 2.2 A

2.2 A or less or more than 2.2 A

⇒ A rectangular pulse train

*s*(

*t*) is shown in figure is convolved with the signal cos

^{2}(4p x 10

^{3}

*t*). The convolved signal will

DC

12 kHZ sinusoidal

8 kHZ sinusoidal

14 kHZ sinusoidal

⇒ The 10 MHz in the specification of CRO means that

the sweep frequency is 10 MHz

the frequency of input signal should not be more than 10 MHz

the vertical amplifier has been designed for 10 MHz

none of the above