Question is ⇒ Characteristic wave impedance is, Options are ⇒ (A) ε/μ, (B) (ε/μ)1/2, (C) Ex/Hy, (D) Hy/Ex, (E) , Leave your comments or Download question paper.

Question is ⇒ Characteristic wave impedance is, Options are ⇒ (A) ε/μ, (B) (ε/μ)1/2, (C) Ex/Hy, (D) Hy/Ex, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Characteristic wave impedance is
A.	ε/μ [Wrong Answer]
B.	(ε/μ)^1/2 [Correct Answer]
C.	E_x/H_y [Wrong Answer]
D.	H_y/E_x [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : B Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Loading of a line means
increasing inductance of line
increasing distributed inductance of line
decreasing distributed inductance of line
decreasing inductance of line

⇒

Assertion (A): Tie set schedule is used in nodal analysis.

Reason (R): Loop currents are fictitious quantities.

Both A and R are true and R is correct explanation of A
Both A and R are true and R is not the correct explanation of A
A is true but R is false
A is false but R is true

⇒ Most electromagnetic transmission in rectangular wave-guide uses
TE₁₀ mode
TE₀₁ mode
TE₂₀ mode
TE_₁₁ mode

⇒ A single phase half wave controlled rectifier circuit has a free wheeling diode. The load is a combination of R and L. The firing angle is a. The period of conduction of SCR and free wheeling diode respectively are
a < ωt < p and p < ωt < (2p + a)
a < ωt < p and p < ωt < 2p
a < ωt < (p + a) and (p + a) < ωt < 2p
a < ωt < p and p < ωt < (2p - a)

⇒ Ideally an attenuator pad should not change
voltage level
impedance level
power level
voltage, power or impedance level

⇒ Value of Z_L for maximum power transfe
R
R + jωL
R - jωL
None of these

⇒ Which of the following instruction modes does not exist in microprocessor 8085?
Inherent
Immediate
Absolute
Indirect

⇒ In pulse code modulation when the maximum frequency in the signal is f_max the bandwidth required will be
≤ p.f_max
≥ p.f_max
≤ (p.f_max)²
≥ (p.f_max)²

⇒ The maximum permissible distance between two samples of a 2 kHz signal is
1000 μ sec
500 μ sec
250 μ sec
2000 sec

⇒ The inputs to a 3 bit binary adder are 111₂ and 110₂. The output will be
101
1101
1111
1110

⇒ Octal number 12 is equal to decimal number
8
9
10
11

⇒ In all insulators the bonding is covalent.
TRUE
FALSE

⇒ Which memory has read operation, byte erase, byte write and chip erase?
RAM
UVEPROM
EEPROM
both (b) and (c)

⇒ For 0 < M < 1, the centres of M circle lie to the right of origin.
TRUE
FALSE

⇒ In an ac circuit, the maximum and minimum values of power factor can be
2 and 0
1 and 0
0 and -1
1 and -1

⇒

Assertion (A): When the forward gain of a system is increased, the transient response becomes oscillatory.

Reason (R): Increasing the forward gain reduces steady state error.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct but R is wrong
R is correct but A is wrong

⇒ In figure, I_D = 4 mA. Then V_{S20 V
16 V
6 V
0.6 V}

⇒ The characteristic impedance of a twin wire feeder used for TV signals is about
1000 ohm
500 ohm
300 ohm
100 ohm

⇒ If operator 'a' = 1 ∠120° then (1 + a²) =
3
3 ∠30°
3 ∠ - 30°
3 ∠60°

⇒ A gate function which occurs at t = t₀ and lasts for duration T can be written as
u (t - t₀ - T)
u(t - t₀) = u(t - t₀ - T)
u(t - t₀) - u(t - t₀ - T)
u(t - t₀) - u(t - t₀ + T)

⇒ In case of frequency modulation, modulating voltage remains constant if the modulating frequency is lowered, then
amplitude of distant sidebands decreases
amplitude of distant sidebands increases
amplitude of distant sidebands remains constant
amplitude of distant sidebands first increases, then decreases

⇒ In an AM transmitter after the modulation stage, class C amplifier
can be used
cannot be used
may be used, but it has no use
can't be determine to use

⇒ RC oscillator can be used upto
1 kHz
10 kHz
50 kHz
100 kHz

⇒

Assertion (A): The resistivity of intrinsic semiconductor decreases with increase in temperature.

Reason (R): The forbidden gap decreases with increase in temperature.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not a correct explanation of A
A is true but R is false
A is false but R is true

⇒ Harmonic distortion analyser
measures amplitude of each harmonic
measures rms value of fundamental frequency component
measures rms value of all harmonics except fundamental frequency
displays rms value of each harmonic on screen of CRO

⇒ (1001-10) is equal to
7
(8)₈
(7)₄
(8)₄

⇒ Which of the following pairs of semiconductors and current carriers is correctly matched?
Intrinsic : number of electrons = number of holes
P type : number of electrons > number of holes
N type : number of electrons < number of holes
Bulk : neither electrons nor holes

⇒ An electromagnetic wave incidents on a perfect insulator at an angle. If the wave is not entirely parallel polarized, then
the reflected wave will be entirely polarized parallel to the plane of incidence
there will be no reflection
the reflected wave will be entirely polarized perpendicular to the plane of incidence
any of the above

⇒ The resolution of a DAC depends on which of the following?
The number of bits
Monotonicity
Reference voltage
The values of resistance

⇒ The value of the integral of the function g(x, y) = 4x³ + 10y⁴ along the straight line segment from the point (0, 0) to the point (1, 2) in the x-y plane is
33
35
40
56