Question is ⇒ Calculate the O/P voltage of a non-inverting constant gain multiplier with R1 = 100 kΩ, Rf= 600 kΩ, V1 = 2 volt, then O/P voltage Vo of non inverting op-amp is given by, Options are ⇒ (A) 16 V, (B) 14 V, (C) 20 V, (D) 15 V, (E) , Leave your comments or Download question paper.

Question is ⇒ Calculate the O/P voltage of a non-inverting constant gain multiplier with R1 = 100 kΩ, Rf= 600 kΩ, V1 = 2 volt, then O/P voltage Vo of non inverting op-amp is given by, Options are ⇒ (A) 16 V, (B) 14 V, (C) 20 V, (D) 15 V, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Calculate the O/P voltage of a non-inverting constant gain multiplier with R₁ = 100 kΩ, R_f= 600 kΩ, V₁ = 2 volt, then O/P voltage V_o of non inverting op-amp is given by
A.	16 V [Wrong Answer]
B.	14 V [Correct Answer]
C.	20 V [Wrong Answer]
D.	15 V [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : B Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ For input and later stages, BI-FET op-amp use
JFETs and MOSFETs respectively
MOSFETs and JFETs respectively
JFETs and BJTs respectively
BJTs and JFETs respectively

⇒ Which of the following is not treated as hexadecimal constant by assembler in 8085?
64 H
5 AFH
AFH
OCFH

⇒

Match the following:

	List I		List II
A.	AM-DSB FC	1.	2
B.	WBFM	2.	1
C.	PCM	3.	3m
D.	AM-DSB	4.	2^2N

A-1, B-2, C-3, D-4
A-2, B-1, C-4, D-3
A-2, B-3, C-4, D-1
A-4, B-3, C-2, D-1

⇒

Match the following:

	List I		List II
A.	bit	1.	10
B.	nat	2.	e
C.	decit	3.	2

A-1, B-2, C-3
A-1, B-3, C-2
A-3, B-2, C-1
A-2, B-3, C-1

⇒ If Laplace transform of f(t) is F(s), then £ f(t - a) u (t - a)= 0
e^as F(s)
e^-as F(s)
- e^as F(s)
- e ^-as F(s)

⇒

Assertion (A): Laplace transform of impulse function is equal to area under the impulse.

Reason (R): An impulse function whose area is unity is called unit impulse function.

Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is correct but R is wrong
R is correct but A is wrong

⇒ A longwave AM broadcast transmitter needs
very small carrier power
very large carrier power
small carrier power
large carrier power

⇒ The emitter bias largely depends on
gain
signal input
I_E
none of the above

⇒ Four memory chips of 16 x 4 size have their address buses connected together. This system will be of size
64 x 4
16 x 16
32 x 8
256 x 1

⇒ A source generates three symbols with probabilities 0.25, 0.25, 0.50 at a rate of 3000 symbols per second. Assuming independent generation of symbols, the most efficient source encoder would have average bit rate is as
6000 bits/sec
4500 bits/sec
3000 bits/sec
1500 bits/sec

⇒ A 'n' bit sequence generator employing SR flip-flop has maximum length of the sequence as :
2ⁿ
n
2ⁿ - 1
2ⁿ^-1

⇒ Let JCOKE = 3 and LPEPSI = 5. Consider the statement 8
1
15
10

⇒ In a receiver, which of the following device has IF input but RF output?
Demodulator
Loudspeaker
Audio amplifier
Frequency changer

⇒ Energy = voltage x charge.
TRUE
FALSE

⇒ Read cycle is always followed by (during instructions execution)
read cycle
write cycle
delete signal
none of these

⇒

Assertion (A): The hybrid p model of a transistor can be reduced to h parameter model and vice versa.

Reason (R): Hybrid p and h parameter models are interrelated as both of them describe the same device.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not a correct explanation of A
A is true but R is false
A is false but R is true

⇒ Which of the following microphones has an inbuilt amplifier?
Condenser
Moving coil
Ribbon
Carbon

⇒ Companding is used
to overcome quantising noise in PCM
in PWM receivers to reduce impulse noise
to protect small signals in PCM from quantising noise
none of the above

⇒ A 400 W carrier is amplitude modulated with m = 0.75. The total power in AM is
400 W
512 W
588 W
650 W

⇒ Which of the following input is not possible in case of a SR flip-flop?
S = 0, R = 0
S = 0, R = 1
S = 1, R = 0
S = 1, R = 1

⇒ The signal input to a given amplifier is made up of 100 mΩ signal power and 1 mΩ noise power. The amplifier contributes an additional 100 mΩ of noise and has a power gain of 20 dB. The output signal-to-noise ratio is
100
50
10
5

⇒ A modem is connected to PC at
serial port
parallel port
SCSI port
input port

⇒ A perfect conductor is a perfect absorber of electromagnetic waves.
TRUE
FALSE

⇒ A computer monitor uses 180 W in normal operation and 20 W in sleep mode. The computer is on all the 24 hours but is in sleep mode for 18 hours a days. The energy units saved in 30 days are
0.54 units
86.4 units
2.88 units
4.8 units

⇒ A transmission line of characteristic impedance z₀ = 50 Ω. Phase Velocity = 2 x 10⁸ m/sec, and length l = 1 m is terminated by a load z₁ = (30 - j 40) ohms. The input impedance of the line for a frequency of 100 MHz will be
(30 + j x 40) Ω
(30 - j 40) Ω
(50 + j x 40) Ω
(50 - j 40) Ω

⇒ As the temperature of an intrinsic semiconductor material is increased
protons get excited
neutrons acquire charge
energy of the atom is increased
additional holes are created in the conduction band

⇒ The output voltage waveform of a CE amplifier is fed to a dc coupled CRO. The trace on the screen will be
dc output voltage
ac output voltage
sum of dc and ac output voltage
either (a) or (b)

⇒ The typical squelch circuit
cuts off IF amplifier when AGC is minimum
cuts off IF amplifier when AGC is maximum
cuts off audio amplifier when carrier is absent
eliminates RF interference when signal is weak

⇒ The effect of adding poles and zeros can be determined quickly by
Nichols chart
Nyquist plot
Bode plot
Root locus

⇒ V(t) across R₂ for t > 0 is given
2 - 2e^-2t
2 - e^-2t
2 - e^-t
1 - e^-t