Question is ⇒ Cables, generally used beyond 66 kV are, Options are ⇒ (A) oil filled, (B) S.L. type, (C) belted, (D) armoured, (E) , Leave your comments or Download question paper.

Question is ⇒ Cables, generally used beyond 66 kV are, Options are ⇒ (A) oil filled, (B) S.L. type, (C) belted, (D) armoured, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Cables, generally used beyond 66 kV are
A.	oil filled [Correct Answer]
B.	S.L. type [Wrong Answer]
C.	belted [Wrong Answer]
D.	armoured [Wrong Answer]
View Answer 9 -8 Explanation:- Answer : A Discuss it below : Haidy Ebrahem Said on 2021-01-20 18:43:45 When a man at distance r from the electrode having a step of approximately 1 m, the associated hazard is called !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Pressure cables are generally not used beyond
11 kV
33 kV
66 kV
132 kV

⇒ The minimum dielectric stress in a cable is at
armour
bedding
conductor surface
lead sheath

⇒ Is a cable is to be designed for use on 1000 kV, which insulation would you prefer ?
Polyvinyle chloride
Vulcanised rubber
Impregnated paper
Compressed SF6 gas

⇒ The surge resistance of cable is
5 ohms
20 ohms
50 ohms
100 ohms

⇒ The intersheaths in the cables are used to
minimize the stress
avoid the requirement of good insulation
provide proper stress distribution
none of the above

⇒ The material for armouring on cable is usually
steel tape
galvanised steel wire
any of the above
none of the above

⇒ In a cable, the maximum stress under operating conditions is at
insulation layer
sheath
armour
conductor surface

⇒ A cable carrying alternating current has
hysteresis losses only
hysteresis and leakage losses only
hysteresis, leakage and copper losses only
hysteresis, leakage, copper and friction losses

⇒ In cables the charging current
lags the voltage by 90°
leads the voltage by 90°
lags the voltage by 180°
leads the voltage by 180°

⇒ The thickness of metallic shielding on cables is usually
0.04 mm
0.2 to 0.4 mm
3 to 5 mm
40 to 60 mm

⇒ Which of the following insulation is used in cables ?
Varnished cambric
Rubber
Paper
Any of the above

⇒ A certain cable has an insulation of relative permittivity 4. If the insulation is replaced by one of relative permittivity 2, the capacitance of the cable will become
one half
double
four times
none of the above

⇒ Dielectric strength of rubber is around
5 kV/mm
15 kV/mm
30 kV/mm
200 kV/man

⇒ ____ cables are used for 132 kV lines.
High tension
Super tension
Extra high tension
Extra super voltage

⇒ Conduit pipes are normally used to protect ____ cables.
unsheathed cables
armoured
PVC sheathed cables
all of the above

⇒ Low tension cables are generally used upto
200 V
500 V
700 V
1000 V

⇒ If a power cable and a communication cable are to run parallel the minimum distance between the two, to avoid interference, should be
2 cm
10 cm
50 cm
400 cm

⇒ The current carrying capacity of cables in D.C. is more than that in A.C. mainly due to
absence of harmonics
non-existence of any stability limit
smaller dielectric loss
absence of ripples

⇒ Solid type cables are considered unreliable beyond 66 kV because
insulation may melt due to higher temperature
of corona loss between conductor and sheath material
there is a danger of breakdown of insulation due to the presence of voids

⇒ The thickness of the layer of insulation on the conductor, in cables, depends upon
reactive power
power factor
voltage
current carrying capacity

⇒ The insulating material for cables should
be acid proof
be non-inflammable
be non-hygroscopic
have all above properties

⇒ PVC stands for
polyvinyl chloride
post varnish conductor
pressed and varnished cloth
positive voltage conductor

⇒ In the cables, the location of fault is usually found out by comparing
the resistance of the conductor
the inductance of conductors
the capacitances of insulated conductors
all above parameters

⇒ The advantage of cables over overhead transmission lines is
easy maintenance
low cost
can be used in congested areas
can be used in high voltage circuits

⇒ The insulating material for a cable should have
low cost
high dielectric strength
high mechanical strength
all of the above

⇒ The electrostatic stress in underground cables is
same at the conductor and the sheath
minimum at the conductor and maximum at the sheath
maximum at the conductor and minimum at the sheath
zero at, the conductor as well as on the sheath

⇒ Copper as conductor for cables is used as
annealed
hardened and tempered
hard drawn
alloy with chromium

⇒ The bedding on a cable consists of
hessian cloth
jute
any of the above
none of the above

⇒ If a cable of homogeneous insulation has a maximum stress of 10 kV/mm, then the dielectric strength of insulation should be
5 kV/mm
10 kV/mm
15 kV/mm
30 kV/mm

⇒ In the cables, sheaths are used to
prevent the moisture from entering the cable
provide enough strength
provide proper insulation
none of the above