Question is ⇒ Buna-S is also called, Options are ⇒ (A) polyurathane, (B) SBR, (C) teflon, (D) bakelite, (E) , Leave your comments or Download question paper.

Question is ⇒ Buna-S is also called, Options are ⇒ (A) polyurathane, (B) SBR, (C) teflon, (D) bakelite, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Buna-S is also called
A.	polyurathane [Wrong Answer]
B.	SBR [Correct Answer]
C.	teflon [Wrong Answer]
D.	bakelite [Wrong Answer]
View Answer 1 -1 Explanation:- Answer : B Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Polyvinyl chloride (PVC) is
a thermosetting material.
a condensation polymerisation product.
made by employing emulsion polymerisation.
none of these.

⇒ __________ resins are produced by the condensation polymerisation of formaldehyde with urea or melamine.
Epoxy
Amino
Alkyd
Phenolic

⇒ __________ is a thermosetting plastic.
PVC
Polythene
Bakelite
polystyrene

⇒ Vulcanisation of rubber does not increase its
softness
oxidation resistance
weight & strength
elasticity & water solubility

⇒ Styrene butadiene rubber (SBR) is never used for making
coated fabrics
front wheel tyres of aeroplanes (i.e., heavy duty tyres)
gaskets
soles of shoes

⇒ Low pressure Zeigler process of polythene manufacture
employs a pressure of 30 kgf/cm².
achieves an yield of 95-98% based on ethylene.
produces very low density polythene.
does not use any catalyst for polymerisation.

⇒ Polymerisation process in which two or more monomers of chemically different nature take part is called
copolymerisation
addition polymerisation
chain polymerisation
none of these

⇒ Polymerisation product of C₂F₄ (carbon tetraflouride) is called P.T.F.E. (poly chloro tetra flouro ethylene). It is also called
polyurethane
silicone rubber
teflon
epoxy resin

⇒ Cross linked polymers formed from bi-and trifuctional groups in which cross-linkage in three dimensions via few chemical bonding across linear chains occur imparts to the polymer __________ properties.
thermoplastic
thermosetting
elastometric
brittleness

⇒ Branched chair polymers as compared to linear polymers have
higher melting point.
higher tensile strength.
lower density.
none of these.

⇒ Acrylonitrile is mainly used in the __________ industry.
polymer
printing
dyeing
photographic

⇒ Poly tetra flouro ethylene (PTFE) is known as
dacron
teflon
bakelite
celluloid

⇒ Temperature and gage pressure maintained during the manufacture of cold SBR (styrene butadiene rubber) are
5°C and 1 kgf/cm².
- 20°C and 1 kgf/cm².
0°C and 1 kgf/cm².
0°C and 3 kgf/cm².

⇒ Addition polymerisation is not involved in the manufacture of
low density polythene.
poly vinyl chloride.
polystyrene.
polyhexamethylene adipamide.

⇒ Phthalic anhydride is used
in making PVC
as plasticisers
in insecticides manufacture
for making nylon-6

⇒ Plastic tubes & pipes are generally made by __________ moulding.
injection
transfer
extrusion
compression

⇒ Terylene is a/an
addition polymer
poly amide
homopolymer
none of these

⇒ The monomer of natural rubber is
DMT
isoprene
2 methyl-1-propene
both (b) and (c)

⇒ In case of dry spinning of polymers, the polymer solution in a volatile solvent is forced through the spinnerates into a warm air chamber, where the solvent evaporates leaving behind the polymer in the filament form. Dry spinning is used for __________ fibres.
polythene
PVC
rayon
polyvinyl acetate

⇒ Nylon-66 compared to nylon-6 has
lower melting point.
more abrasion resistant properties.
higher hardness.
all (a), (b) and (c).

⇒ Which of the following is the lowest cost plastic commercially available ?
Polythene
Teflon
Bakelite
PVC

⇒ Vulcanisation of rubber
decreases its tensile strength.
increases its ozone & oxygen reactivity.
increases its oil & solvent resistance.
converts its plasticity into elasticity.

⇒ Rain coats are made of
neoprene
PVC
polyurathane
SBR

⇒ All thermoplastic, thermosetting & elastic materials can be processed in a extrusion machine, however it can not be used for the production of plastic
filaments
pipes
buckets
tubings

⇒ Main constituent of natural rubber is
polystyrene
polyisoprene
polybutadiene
poly chloroprene

⇒ The main use of butadiene is
as a plasticiser for unsaturated polyester.
in the manufacture of synthetic rubber.
as an anti-skimming agent in paint.
none of these.

⇒ Lavatory cisterns are normally made of
expanded polystyrene
saturated polyester
perspex
PVC

⇒ __________ moulding is used for shaping of thermosetting plastics exclusively.
Compression
Injection
Transfer
Extrusion

⇒ Polycondensation reaction of polymerisation
does not produce linear polymers.
produces only thermoplastic material.
produces epoxy polymers.
does not need any catalyst.

⇒ Catalyst used in the production of high density polythene by low pressure Ziegler process is
aluminium triethyl activated with TiCl₄
platinum
molybdenum
Nickel