Question is ⇒ <b>Statement 1, Options are ⇒ (A) Statement 1 is true but statement 2 is false, (B) Statement 1 is false but statement 2 is true, (C) Both the statements are true, (D) Both the statements are false, (E) , Leave your comments or Download question paper.

Question is ⇒ <b>Statement 1, Options are ⇒ (A) Statement 1 is true but statement 2 is false, (B) Statement 1 is false but statement 2 is true, (C) Both the statements are true, (D) Both the statements are false, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Statement 1
A.	Statement 1 is true but statement 2 is false [Wrong Answer]
B.	Statement 1 is false but statement 2 is true [Wrong Answer]
C.	Both the statements are true [Correct Answer]
D.	Both the statements are false [Wrong Answer]
View Answer 2 -1 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Ferromagnetic materials
shows spontaneous magnetisation below a certain temperature
have resistivity very high as compared to that of iron
can be used even at microwave frequencies
all of the above

⇒ From an n channel JFET for V_DS constant and if V_GS is made more negative, pinch off would occur at
higher value of drain current
saturation value of drain current
zero drain current
gate current equal to drain current

⇒ Transistor are free from which type of noise?
Resistance noise
Partition noise
Flicker noise
Shot noise

⇒ In a BJT amplifier circuit the size of coupling capacitor depends on
lowest frequency
highest frequency
average of lowest and highest frequencies
none of the above

⇒ The phase margin and damping ratio have no relation.
TRUE
FALSE

⇒ If F(t) = δ(t - a), F(s)=
0
1
e^-as
e^as

⇒

Assertion (A): Secondary instruments require calibration at frequent intervals.

Reason (R): Secondary instruments have many errors.

Both A and R are true and R is correct explanation of A
Both A and R are true but R is not correct explanation of A
A is true R is false
A is false R is true

⇒ In 8421 Binary coded Decimal system the decimal number 237 is represented by
1000110111
1000111110
1000110111
10010010011

⇒ A buffer amplifier should have
high output impedance and high input impedance
high output impedance and low input impedance
low output impedance an low input impedance
low output impedance and high input impedance

⇒ Out of the three transforms viz. Z-transform, Laplace transform and Fourier transform
all three are used in continuous time domain
all three are used in both continuous time domain and discrete time domain
Z transform is used in continuous time domain while Laplace and Fourier transforms are used in discrete time domain
Z transform is used is discrete time domain while Laplace and Fourier transforms are used in continuous time domain

⇒ In figure, E = 1 V (rms value). The average power is 250 mW. Then phase angle between E and
90°
60°
45°
30°

⇒ The expression Y (A, B, C) = ∑m (1, 3, 5, 6) is to realized using a multiplexer. Then
use 8 : 1 multiplexer and ground input lines 1, 3, 5, 6
use 8 : 1 multiplexer and ground input lines 0, 2, 4, 7
use 8 : 1 multiplexer and ground input lines 0, 1, 2, 3
use 8 : 1 multiplexer and ground input lines 4, 5, 6, 7

⇒ 8255 A has three 8 bit ports A, B, C for peripheral data transfer. For programming 8255 A, these ports are grouped as
Port A with Port B
Port A with 4 most significant ports of C, port B with 4 least significant ports of C
Port A with Port C
none of the above

⇒ RF amplifiers are used in radio receivers for
better sensitivity
improved signal-to-noise ratio
better coupling of receiver to the antenna
all of the above

⇒ V MOS have the advantage of
faster switching
no thermal run away
both (a) and (b)
none of the above

⇒ In a CE amplifier circuit the dc voltage between emitter and ground
is always zero
cannot be zero
may or may not be zero
is negative

⇒ In the circuit of figure the voltage across C at t = 0^{+0 V
20 V
very large
7.5 V}

⇒ As wavelength decrease the size of high directivity antenna
decreases
increases
is not affected
either (b) or (c)

⇒ In the given figure,
(A + B)C + DE
AB + C(D + E)
(A + B)C + D + E
none of the above

⇒ In a modified series inverter
the maximum output frequency is less than frequency of damped oscillations
the output frequency can be even higher than the frequency of damped oscillations
the output frequency cannot exceed the frequency of damped oscillations
any of the above

⇒ In the circuit of fi
V_a would always lag V_b
V_a would always lead V_b
V_a and V_b can be in phase
phase angle between V_a and V_b would always be 90°

⇒ For the current wave i = 10 + 10 sin θ, the rms value is
0.416666666666667
12.247 A
20 A
14.14 A

⇒ Speeds of sound and radio waves are equal.
TRUE
FALSE

⇒ The term critical frequency denotes
the lowest frequency that is reflected by the ionosphere
the highest frequency that is reflected by the ionosphere at vertical distance
the lowest frequency by which communication is possible between two given points
none of the above

⇒ For type 1 system the velocity lag error is
inversely proportional to bandwidth of system
directly proportional to gain constant
inversely proportional to gain constant
independent of gain constant

⇒ The 2's complement representation of the decimal number -4 is
100
1100
1011
1010

⇒ The Lissajous pattern observed on screen of CRO is a straight line inclined at 45° to x axis. If X-plate input is 2 sin ωt, the Y-plate input is
2 sin ωt
2 sin (ωt + 45°)
2 sin (ωt - 45°)
22 sin ωt + 45°)

⇒ The function to Calculate the maximum value in the specified field of a database is
DM
DMAX
MAX
DBMAX

⇒ Filter method and phasing method are the methods for generating
SSB signal
vestigial side band signal
both SSB and vestigial sideband signals
none of the above

⇒ A duplexer is used to
couple two antennas to a transmitter
isolate the antenna from the local oscillator
prevent interference between two antennas connected to receiver
use an antenna for reception or transmission without interference