Question is ⇒ Binary 1111 when subtracted from binary 11111 is, Options are ⇒ (A) 101110, (B) 10110, (C) 10000, (D) 100010, (E) , Leave your comments or Download question paper.

Question is ⇒ Binary 1111 when subtracted from binary 11111 is, Options are ⇒ (A) 101110, (B) 10110, (C) 10000, (D) 100010, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	Binary 1111 when subtracted from binary 11111 is
A.	101110 [Correct Answer]
B.	10110 [Wrong Answer]
C.	10000 [Wrong Answer]
D.	100010 [Wrong Answer]
View Answer 1 -6 Explanation:- Answer : A Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ The ideal voltmeter V of figure will read __________ v
0
10
5
1

⇒ The dominant mode in a rectangular wave-guide is
TE₀₁
TM₀₁
TE₁₀
TM₁₁

⇒ Which one of the following power amplifier has the maximum efficiency?
Class A
Class B
Class AB
Class C

⇒ Out of latch and flip flop, which has clock input?
Latch only
Flip flop only
Both latch and flip flop
None

⇒ The sum of two sine waves of different frequencies is a sine wave.
TRUE
FALSE

⇒ A coil has a designed for high Q performance at a rated voltage and a specified frequency. If the frequency of operation is doubled, and the coil is operated at the same rated voltage, then the Q factor and the active power P consumed by the coil will be affected as follows.
P is doubled, Q is halved
P is halved, Q is doubled
P remains constant, Q is doubled
P decreases 4 times, Q is doubled

⇒ In the self biasing scheme (R_F across collector to base) of BJT, S₁ tends to unity by __________ R_C is the collector load Resistance.
increasing R_F
decreasing R_F
decreasing R_F and increasing R_C
increasing R_F and decreasing R_C

⇒ As per Matthiessen's rule, the total resistivity r of a conductor can be written as r = r_i + aT, where r_i and a are constants and T is absolute temperature. At very low temperatures
aT = 0
aT > r_i
aT ∼ r_i
aT < r_i

⇒ With reference to C programming language, which of the following statements are correct?

An identifier may start with an underscore.
An identifier may end with an underscore.
If is a valid identifier.
The number of significant characters in and identifier is implementation dependent.

Select the correct answer from the codes given below:
1 and 2 only
2 and 3 only
1, 2, 3 and 4
3 and 4 only

⇒ In AM increased depth of modulation increases __________ and in FM with increased depth of modulation __________ increases.
total transmitted power, bandwidth
bandwidth, bandwidth
bandwidth, total transmitted power
total transmitted power, sideband power

⇒ In 8085 the instruction MOV A, M is an example of
Direct addressing
Immediate addressing
Register addressing
Register indirect addressing

⇒ MEWS stands for
Missile Early Warning System
Moving Target Early warning System
Missile Early Warning Signal
Moving Target Early Warning Signal

⇒ At 20 GHz , the gain of a parabolic dish antenna of 1 meter diameter and 70% efficiency is
15 dB
25 dB
35 dB
45 dB

⇒ The fact that domains exhibits spontaneous magnetisation is
first hypothesis is of Curie
second hypothesis is of Weiss
Curie-Weiss law
Boltzmann's statistics

⇒ In order to enable TRAP interrupt, which of the following instructions are needed?
El only
SIM only
El and SIM both
None

⇒ Voltage standing wave pattern in a loss less transmission line with characteristic impedance 50 Ω and a resistive load is shown in the figu
50 Ω
200 Ω
12.5 Ω
0 Ω

⇒ In FM and AM the ratio of signal to noise ratio at the detector output least depends upon
bandwidth
transmission
carrier frequency
modulating frequency

⇒ The mean life time of carrier may range from 10^-9 seconds to hundreds of μ-seconds.
TRUE
FALSE

⇒ A generator with an internal resistance of 600 Ω drives an amplifier whose input resistance is 400 Ω. The generator's open circuit voltages is 1 mV; the amplifier develops 100mV across an 8kΩ load. The power gain is
125
250
1125
3125

⇒ Indium, aluminium, arsenic are all p type impurities.
TRUE
FALSE

⇒ The analog signal m(t) is given below m(t) = 4 cos 100 pt + 8 sin 200 pt + cos 300 pt, the Nyquist sampling rate will be
1/100
1/200
1/300
1/600

⇒ The main purpose of using transformer coupling in a class A amplifier is to make it more
efficient
less costly
less bulky
distortion free

⇒ The ripple factor of power supply is a measure of
its filter efficiency
diode rating
its voltage regulation
purity of power output

⇒ For a 50 Ω resistor for 3 GHz application, the stray capacitance should be less than
1 μF
1 nF
1 pF
0.1 pF

⇒ In the circuit of figure the current through 5 Ω resistance at t = &infin
0.166666666666667
2.5 A
3.1 A
0

⇒ The total number of leads in MOS controlled thyristor is
2
3
4
2 or 3

⇒ In which of the following device electrons will be the majority carriers?
P-type semiconductor
N-type semiconductor
N-P-N transistor
P-N-P transistor

⇒ The following switching functions are to be implemented using a decoder

f₁ = ∑m (1, 2, 4, 8, 10, 14)
f₂ = ∑m (2, 5, 9, 15)
f₃ = ∑m (2, 4, 5, 6, 7)

The minimum configuration of decoder is
2 to 4 line
3 to 8 line
4 to 16 line
5 to 32 line

⇒ The signal x(t) = A cos (ω₀t + φ) is
energy signal
power signal
energy Power
none

⇒ Voltage series feedback (Also called series-shunt feedback) results in
increase in both I/P and O/P impedances
decrease in both I/P and O/P impedances
increase in I/P impedance and decrease in O/P impedance
decrease in I/P impedance and increase in O/P impedance