Question is ⇒ At room temperature a semiconductor material is, Options are ⇒ (A) perfect insulator, (B) conductor, (C) slightly conducting, (D) any of the above, (E) , Leave your comments or Download question paper.

Question is ⇒ At room temperature a semiconductor material is, Options are ⇒ (A) perfect insulator, (B) conductor, (C) slightly conducting, (D) any of the above, (E) , Leave your comments or Download question paper. Previous question Next question


Q1.	At room temperature a semiconductor material is
A.	perfect insulator [Wrong Answer]
B.	conductor [Wrong Answer]
C.	slightly conducting [Correct Answer]
D.	any of the above [Wrong Answer]
View Answer 10 -2 Explanation:- Answer : C Discuss it below : !! OOPS Login [Click here] is required to post your answer/result Help other students, write article, leave your comments

Previous question Next question

Also Read Similar Questions Below :

⇒ Which inverter circuit uses coupled inductors?
Modified McMurray full bridge inverter
McMurray Bedford half bridge inverter
Modified McMurray Bedford half bridge inverter
Both (b) and (c)

⇒ When P_c is the unmodulated carrier power and P_t is the total power in the modulated wave, then the maximum power in AM wave is
P_t = 1.5 P_c
P_t = 2.5 P_c
P_t = 2
P_t = 22 P_c

⇒ On which bands, do the optical fibers operate?

Ultra violet band
Ultra high frequency band
Visible light band
Infrared band

Select the correct answer from the codes given below:
1 only
1 and 2 only
1, 2 and only
1, 3 and 4

⇒ Which of the statement is correct?
h and g matrices are inverse of each other
z and y matrices are inverse of each other
for reciprocal networks AD - BC = 1
ABCD parameters are used in transistor circuit

⇒ In the case of the circuit shown in the figure, the collector current I_C will be, if β = 100, V_BE = 0.7 V, I_CO = 0.1 βA at 20&d
2.26 mA
1.85 mA
0.357 mA
0.185 mA

⇒ In 2's complement addition, the carry generated in the last stage is
added to LSB
neglected
added to bit next to MSB
added to the bit next to LSB

⇒ For a wave v = V _1m sin (ωt + θ₁ ) - V_3m sin (3ωt + θ₃), the rms value is (0.5 V²_1m + 0.5 V²_3m)^0.5
TRUE
FALSE

⇒ In order to obtain triangular pulses at the output of the circuit in the figure, the input should
grounded
a square wave
Triangular wave
Trigger

⇒ Which of the following does not characterize a ferromagnetic material?
Coercivity
Permeability
Permittivity
Reluctance

⇒ Which of the following is not a keyword in C?
int
float
return
capital

⇒ In CC configuration, the output signals has approximately
the same amplitude and phase
opposite amplitude and phase
same amplitude but opposite phase
none of the above

⇒ In a 3 phase semiconverter, the output voltage becomes discontinuous for
firing angle > 30°
firing angle > 60°
firing angle > 90°
firing angle > 120°

⇒

Match the following:

	List I		List II
A.	Copper	1.	produces discrete energy level just above valence band
B.	Rubber	2.	produces discrete energy level just below conduction band
C.	Antimony	3.	large forbidden gap
D.	Boron	4.	valence and conduction bands overlap

A-1, B-2, C-4, D-3
A-4, B-1, C-2, D-3
A-4, B-3, C-1, D-2
A-2, B-1, C-3, D-4

⇒ The statement IMPLICIT INTEGER (A - F) in FORTRAN identifies
all variable names which begin with A, B, C, D, E or F as being of integer type
all character names which begin with A, B, C, D, E, or F as being of integer type
all variable names which begin with A and have 6 characters
none of the above

⇒ For circuit in figure, which combination of V_TH and R_TH represents the circuit as seen from ab<
1 V, 10 Ω
1 V, 1000 Ω
1 mV, 1000 Ω
1 mV, 10 Ω

⇒ The distance between maxima and minima of a standing wave is
λ/4
λ/2
λ
2λ

⇒ The domain mode in rectangular waveguide is
TE₀₁
TE₀₂
TE₁₀
TM₁₁

⇒ A series circuit has R = 5 Ω and C = 10 μF. At t = 0 it is switched on to a 10 V dc battery. The maximum current in the circuit is
0.0833333333333333
0.0416666666666667
10⁶A
10 μA

⇒ The measure of mismatch between the load and the transmission line is known as
directivity
Gain
standing wave ratio
reflection coefficient

⇒ A modem is connected to PC at
serial port
parallel port
SCSI port
input port

⇒ Consider the following statements:
In the 2's complement representation, negative numbers are stored in sign magnitude form.
Taking 2's complement is equivalent to sign change.
In a 4 bit complement representation of a binary number A.
In the 2's complement representation the most significant bit (MSB) is zero for a positive number.
Of these, the only true statements are
(I) and (III)
(I) and (IV)
(II) and (III)
(II) and (IV)

⇒ The effective height of an antenna is slightly greater than physical height because
wave velocity in conductor is less than its velocity in free space
wave velocity in conductor is more than its velocity in free space
resistance of conductor is less than that of free space
none of the above

⇒ In p type semiconductor holes are majority carriers.
TRUE
FALSE

⇒
Assertion (A): The modified ramp function of the given figure can be represented s sum of two ramp functions of the given fig
Both A and R are correct and R is correct explanation of A
Both A and R are correct but R is not correct explanation of A
A is true, R is false
A is false, R is true

⇒ Leak type bias is used in a plate-modulated class C amplifier to
prevent tuned circuit damping
prevent over modulation
increase the bandwidth
prevent excessive grid current

⇒ A signal x(n) = sin(ω₀n + φ) is the input to a linear time invariant system having a frequency response H(e^jω) If the O/P of the system is Ax(n -n₀), then the general form of H(e^jω) will be
- n₀ω₀ + β for any arbitrary real β
- n₀ω₀ + 2pk for any arbitrary integer k
n₀ω₀ + 2pk for any arbitrary integer k
- n₀ω₀ + φ

⇒ The component in the given figur
attenuator
T type low pass filter
T type high pass filter
phase shifter

⇒ In which one of the following types of analog to digital convertors the conversion time is practically independent of the amplitude of the analog signal?
The dual slope integrating type
Successive approximation type
Counter ramp type
Tracking type

⇒ The gain of an half wavelength antenna is
2.15 dB
10 dB
1.78 dB
100 dB

⇒ Each instruction in assembly language program has the following fields:
Lable field
Mnemonic field
Operand field
Comment field
The correct sequence of these fields is?
1, 2, 3, 4
1, 2, 4, 3
2, 1, 3, 4
2, 1, 4, 3

Users Also Read
Previous Papers

Aptitude

Reasoning

Gen.Knowledge

Speak English

English / Verbal

Online / Mock Test

Vedic Math